Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY › from 2021.08
RM37H0E _59 Vehicle Exterior _093353 LIGHTING (EXT) _0448240 HEADLIGHT ASSEMBLY A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (DISASSEMBLY)
E463000N01
3.583,2.708 5.021,3.906 1.438,1.198 4.323,3.521 4.625,3.521 false 2.354,2.802 2.865,2.802 false 2.781,1.271 3.24,1.271 false 5.021,3.427 5.323,3.427 false 4.167,3.167 4.469,3.167 false 5.406,3.323 5.688,3.677 0.281,0.354 18 false 1 4.656,3.073 4.938,3.427 0.281,0.354 18 false 2 2.583,1.135 2.865,1.49 0.281,0.354 18 false 3 2.948,2.688 3.229,3.042 0.281,0.354 18 false 4 4.677,3.458 4.99,3.656 0.313,0.198 10 false *1 1.51,2.896 1.969,3.094 0.458,0.198 10 false x 3 2.438,1.188 2.594,1.385 0.156,0.198 10 false ● 4.521,3.083 4.677,3.281 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 HEADLIGHT ECU SUB-ASSEMBLY LH 81056A - - -
2 HEADLIGHT GASKET 81134 - - -
3 NO. 1 HEADLIGHT PROTECTOR LH 81176 - - -
4 FRONT NO. 2 BUMPER RETAINER BRACKET 52354 - - -

*1 Headlight ECU LH - -
● Non-reusable part - -

E476435N03
1.531,2.146 4.104,3.552 2.573,1.406 4.208,2.146 7.01,3.563 2.802,1.417 1.833,5.083 2.917,5.083 false 4.396,1.115 3.958,1.115 false 4.344,4.375 5.469,4.375 false 4.073,1.823 4.563,1.823 false 2.333,2.865 2.635,2.865 false 4.948,2.823 5.115,2.823 false 3.833,2.917 3.833,3.229 3.833,3.229 3.594,3.229 false 3.615,2.26 3.896,2.26 3.896,2.26 3.896,2.583 false 6.698,2.469 6.698,2.771 false 4.552,0.438 5.042,0.438 false 6.323,2.521 6.323,2.854 false 6.865,0.615 7.125,0.771 0.26,0.156 10 false x 9 3.323,4.958 3.521,5.24 0.198,0.281 18 false 6 5.969,4.323 6.146,4.5 0.177,0.177 10 false ● 6.198,4.24 6.396,4.521 0.198,0.281 18 false 7 2.052,2.719 2.365,3.031 0.313,0.313 18 false 9 4.906,1.698 5.375,2 0.469,0.302 18 false 8 3.76,1.052 4.031,1.313 0.271,0.26 10 false *1 3.875,3.313 4.333,3.51 0.458,0.198 10 false x 2 5.885,2.615 6.344,2.813 0.458,0.198 10 false x 2 1.604,2.198 1.979,2.438 0.375,0.24 12 false *A 4.281,2.219 4.656,2.458 0.375,0.24 12 false *B 4.667,2.719 4.979,3.031 0.313,0.313 18 false 9 3.281,3.104 3.594,3.417 0.313,0.313 18 false 11 6.594,2.823 6.906,3.135 0.313,0.313 18 false 11 4.271,0.323 4.583,0.635 0.313,0.313 18 false 5 3.333,2.156 3.646,2.469 0.313,0.313 18 false 10 6.208,2.906 6.521,3.219 0.313,0.313 18 false 10 3.531,2.625 3.99,2.823 0.458,0.198 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

5 NO. 1 HEADLIGHT COVER 81144 - - -
6 HEADLIGHT LENS SUB-ASSEMBLY LH 8110B (Click here) - -
7 HEADLIGHT LENS GASKET 81132B (Click here) - -
8 LIGHT CONTROL LED ECU LH 85967D (Click here) - -
9 HEADLIGHT UNIT LH 81171A (Click here) - -
10 HEADLIGHT BRACKET LH 81158 - - -
11 HEADLIGHT LEVELING MOTOR LH 85691 - - -

*A w/ Adaptive High Beam System *B w/o Adaptive High Beam System
*1 HEADLIGHT HOUSING SUB-ASSEMBLY LH - -
● Non-reusable part - -

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 81056A 1.REMOVE HEADLIGHT ECU SUB-ASSEMBLY LH

Hide 81134 2.REMOVE HEADLIGHT GASKET

Hide 81176 3.REMOVE NO. 1 HEADLIGHT PROTECTOR LH

a.
E457905


Hide 52534 4.REMOVE FRONT NO. 2 BUMPER RETAINER BRACKET

a.
E457906


Hide 81144 5.REMOVE NO. 1 HEADLIGHT COVER

a.
E458141C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 8110B 6.REMOVE HEADLIGHT LENS SUB-ASSEMBLY LH

Z101186

NOTICE:
·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop antistatic mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Perform work using clean rubber gloves.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.




SST
09890-47010  (09891-04020, 09891-04010, 09891-04030, 09891-04040)

a.
E457907C01
0.469,0.292 1.146,0.677 0.677,0.385 18 false i, ii 4.302,0.271 4.583,0.625 0.281,0.354 18 false iii 3.146,1.094 3.458,1.292 0.313,0.198 10 false *a
*a TORX Screw - -
V113146

Place Hand Here
V100135

Screw


i.

Remove the 8 screws.


ii.

Using a T20H TORX driver, remove the TORX screw.


iii.

Place your hands at the positions shown in the illustration and detach the claw.



b.
E457909C01
3.604,2.24 4.198,2.49 true 4.406,2.198 4.688,2.406 true 5.958,2.219 6.24,2.427 true 6.396,2.625 6.219,2.646 true 5.208,2.323 5.646,2.51 true 5.49,3.063 5.625,2.698 true 3.979,3.094 4.115,2.729 true 1.979,0.958 2.292,1.156 0.313,0.198 10 false *a 0.594,0.323 0.875,0.677 0.281,0.354 18 false i 3.75,0.292 4.031,0.646 0.281,0.354 18 false ii 1.198,2.219 2.531,2.604 1.333,0.385 18 false iii, iv, v 4.26,2.094 4.573,2.292 0.313,0.198 10 false *1 5.76,2.135 6.073,2.333 0.313,0.198 10 false *1 6.417,2.573 6.729,2.771 0.313,0.198 10 false *2 5.052,2.219 5.365,2.417 0.313,0.198 10 false *3 3.406,2.167 3.719,2.365 0.313,0.198 10 false *3 5.406,3.115 5.615,3.344 0.208,0.229 10 true *4 3.885,3.104 4.094,3.333 0.208,0.229 10 true *4
*1 Cable Tie *2 Headlight Lens Gasket
*3 Headlight Lens LH *4 Headlight Housing Sub-assembly LH
*a 7.6 mm (0.299 in.) - -


i.

Prepare the cable tie of approximately 7.6 mm (0.299 in.) in width.

HINT:

It will be difficult to pull out the headlight lens gasket with a cable tie with a narrow width (2.5 mm (0.0984 in.), etc.).



ii.

Use a heat light to heat the headlight lens gasket near the location where the cable tie is inserted from the backside of the headlight housing sub-assembly LH.

NOTICE:

To prevent the headlight housing sub-assembly LH from deformation or damage, do not heat one part intensively and do not heat with a temperature of 120°C or higher.


HINT:

When the headlight lens gasket is heated, it softens and becomes easier to pull out.



iii.

Insert the cable tie until it sticks into the headlight lens gasket as shown in the illustration.

NOTICE:

Do not damage the groove of the headlight housing sub-assembly LH gasket or the headlight lens.



iv.

Pull out the cable tie and headlight lens gasket together.


v.

Pull out the headlight lens gasket until there is no contact between the headlight lens sub-assembly LH and the headlight housing sub-assembly LH.

HINT:

If the headlight lens gasket disconnects while it is pulled out, insert the cable tie again and pull out the headlight lens gasket.




c.
E462838N01
2.24,0.177 2.521,0.531 0.281,0.354 18 false i

i.

Disconnect the connector.



d.
E455088C03
0.313,0.615 0.594,0.969 0.281,0.354 18 false i
V113147

Remove in this Direction - -


i.

Remove the headlight lens sub-assembly LH as shown in the illustration.



Hide 81132B 7.REMOVE HEADLIGHT LENS GASKET

Z101186

NOTICE:
·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop antistatic mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Perform work using clean rubber gloves.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.




SST
09890-47010  (09891-04020, 09891-04010, 09891-04030, 09891-04040)

a.
E457910


Hide 85967D 8.REMOVE LIGHT CONTROL LED ECU LH

Z101186

Click here(Click here)

Hide 81171A 9.REMOVE HEADLIGHT UNIT LH

Z101186

NOTICE:
·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop antistatic mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Perform work using clean rubber gloves.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.




SST
09890-47010  (09891-04020, 09891-04010, 09891-04030, 09891-04040)

a.
E462973N02
3.208,2.802 3.438,2.979 0.229,0.177 10 true a 5.031,2.875 5.26,3.052 0.229,0.177 10 true b 0.646,0.219 0.927,0.573 0.281,0.354 18 false i

i.

Using a vernier caliper, record the dimensions of a and b shown in the illustration.



b.
E462974C01
0.823,2.229 7.031,4.51 6.208,2.281 1.76,2.823 2.146,2.99 true 4.74,2.76 5.125,2.917 true 0.625,0.24 1.104,0.594 0.479,0.354 18 false i,iii 0.594,2.417 0.875,2.771 0.281,0.354 18 false ii 0.896,2.292 1.271,2.531 0.375,0.24 12 false *A 4.26,2.292 4.635,2.531 0.375,0.24 12 false *B 1.583,2.74 1.896,2.938 0.313,0.198 10 false *1 4.542,2.677 4.854,2.875 0.313,0.198 10 false *1
*A w/ Adaptive High Beam System *B w/o Adaptive High Beam System
*1 Pivot Collar - -
V113146

Place Hand Here
V113147

Turn in this Direction
V113148

Remove in this Direction - -


i.

Loosen the aiming screws for beam axis vertical and horizontal adjustments counterclockwise by 10 turns.


ii.

Place your hand in a protective glove at the position in the illustration, pull in the direction shown in the illustration, and disconnect the pivot collar.


iii.

Hold the headlight unit assembly LH with one hand to prevent it from tipping over and loosen the aiming screws for beam axis vertical and horizontal adjustments counterclockwise until the headlight unit assembly LH is disconnected.



c.
E462975C03
0.531,0.26 6.865,2.396 6.333,2.135 0.656,0.344 1.031,0.583 0.375,0.24 12 false *A 4.396,0.344 4.771,0.583 0.375,0.24 12 false *B 0.094,0.229 0.813,0.625 0.719,0.396 18 false i, ii
*A w/ Adaptive High Beam System *B w/o Adaptive High Beam System


i.

w/ Adaptive High Beam System:

Disconnect the 2 connectors and detach the wire harness clamp and remove the headlight unit LH.


ii.

w/o Adaptive High Beam System:

Disconnect the connector and detach the wire harness clamp and remove the headlight unit LH.



Hide 81158 10.REMOVE HEADLIGHT BRACKET LH

a.

w/ Adaptive High Beam System:

E462841C01
0,0 0,0 false
V100135

Screw
V100136

Connector



b.

w/o Adaptive High Beam System:

E462842C01
0,0 0,0 false
V100135

Screw
V100136

Connector



Hide 85691 11.REMOVE HEADLIGHT LEVELING MOTOR LH

a.

w/ Adaptive High Beam System:

E462839C01
0,0 0,0 false
V113147

Remove in this Direction
V100135

Screw



b.

w/o Adaptive High Beam System:

E462840