Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for TOYOTA Connect) › from 2021.08
RM37H0E _56 Audio / Visual / Telematics _095262 TELEMATICS _0484973 TELEMATICS SYSTEM(for TOYOTA Connect) Y

TELEMATICS  TELEMATICS SYSTEM(for TOYOTA Connect)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the telematics system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CHECK PROBLEM SYMPTOM
2.CHECK PROBLEM SYMPTOM
a.

The telematics system provides a variety of functions. Therefore, it is important to identify whether a malfunction is related to the communication system, including radio wave conditions, or any other systems. Carefully confirm the conditions that caused the malfunction in order to determine if a temporary problem with the radio wave signal conditions caused the malfunction.

Displayed Message and Problem Symptom Cause
A message is temporarily displayed indicating to try again after waiting for a while because the lines are busy. This is caused when there is a problem with the radio wave signal conditions or when the base station is busy. This is not a malfunction (inform the customer that this is not a malfunction and ask them to use the system as is).


Result:
Proceed to
NEXT



NEXT

3.INSPECT AUXILIARY BATTERY
3.INSPECT AUXILIARY BATTERY
a.

Measure the auxiliary battery voltage with the ignition switch off.

Standard voltage:

11 to 14 V (ignition switch off)


HINT:

If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.



Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN communication system DTCs are not output. A
CAN communication system DTCs are output. B



A

5.CHECK FOR DTC*

B

5.CHECK FOR DTC*
Body Electrical > Telematics > Trouble Codes
50001 459
Result:
Result Proceed to
DTCs are output. A
DTCs are not output. B



A

6.CLEAR DTC*

B

12.PROBLEM SYMPTOMS TABLE
6.CLEAR DTC*
Body Electrical > Telematics > Clear DTCs
50002 459
HINT:

The current DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.


Result:
Proceed to
NEXT



NEXT

7.RECHECK FOR DTC*
7.RECHECK FOR DTC*
Body Electrical > Telematics > Trouble Codes
50001 459
Result:
Result Proceed to
DTCs are output. A
DTCs are not output. B


HINT:
·

Even if the malfunction symptom is not confirmed, check for DTCs. This is because the system stores history DTCs.

·

Check the DTCs and inspect the area that the code indicates.




A

8.CHECK CIRCUIT

B

11.CHECK VEHICLE CONTROL HISTORY*
8.CHECK CIRCUIT
a.

Adjust, repair or replace as necessary.

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System (for TOYOTA Connect).

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for TOYOTA Connect)>PRECAUTION



Result:
Proceed to
NEXT



NEXT

9.RECHECK FOR DTC*
9.RECHECK FOR DTC*
HINT:

After clearing DTCs, recheck for DTCs.


Body Electrical > Telematics > Clear DTCs
50002 459
Body Electrical > Telematics > Trouble Codes
50001 459
Result:
Proceed to
NEXT



NEXT

10.PERFORM CONFIRMATION TEST
10.PERFORM CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END

11.CHECK VEHICLE CONTROL HISTORY*
a.

Check for vehicle control history and note any codes that are output.

Body Electrical > Telematics > Utility
Tester Display
Vehicle Control History (RoB)
50005 459 55

Result:
Result Proceed to
No vehicle control history is output A
Any vehicle control history is output B



A

12.PROBLEM SYMPTOMS TABLE

B

12.PROBLEM SYMPTOMS TABLE
a.

Refer to Problem Symptoms Table.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for TOYOTA Connect)>PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table. A
Fault is listed in Problem Symptoms Table. B


HINT:

If the symptom does not recur and no DTCs are output, perform the simulation method.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING




A

13.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM

B

8.CHECK CIRCUIT
13.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM

NEXT

8.CHECK CIRCUIT