Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1DD514  Radiator Rotary Valve Circuit 1 Circuit Short to Ground or Open  P1EFD14  Radiator Rotary Valve Circuit 2 Circuit Short to Ground or Open  P1EFE14  Radiator Rotary Valve Circuit 3 Circuit Short to Ground or Open  P1EFF14  Radiator Rotary Valve Circuit 4 Circuit Short to Ground or Open  


DESCRIPTION

The FC control ECU regulates the FC cooling water temperature control valve so as to maintain the FC stack coolant temperature at a specified level. In order to obtain an appropriate FC stack coolant temperature for the FC stack power generation, the FC control ECU switches the direction of the coolant passage to the bypass side if the FC stack coolant temperature is below a target temperature, or to the radiator if the temperature is above a target.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1DD514 Radiator Rotary Valve Circuit 1 Circuit Short to Ground or Open No +B low voltage when ignition switch is ON, output is off at all the 4 terminals of the FC cooling water temperature control valve step motor, or the WRA1 terminal is judged as abnormal for 1 second or more while the motor is running.
(1 trip detection logic)
·

FC cooling water temperature control valve

·

FC control ECU

·

FC-B relay

·

Wire harness or connector


Master Warning: Comes on FC A
P1EFD14 Radiator Rotary Valve Circuit 2 Circuit Short to Ground or Open No +B low voltage when ignition switch is ON, output is off at all the 4 terminals of the FC cooling water temperature control valve step motor, or the WRA2 terminal is judged as abnormal for 1 second or more while the motor is running.
(1 trip detection logic)
·

FC cooling water temperature control valve

·

FC control ECU

·

FC-B relay

·

Wire harness or connector


Master Warning: Comes on FC A
P1EFE14 Radiator Rotary Valve Circuit 3 Circuit Short to Ground or Open No +B low voltage when ignition switch is ON, output is off at all the 4 terminals of the FC cooling water temperature control valve step motor, or the WRB1 terminal is judged as abnormal for 1 second or more while the motor is running.
(1 trip detection logic)
·

FC cooling water temperature control valve

·

FC control ECU

·

FC-B relay

·

Wire harness or connector


Master Warning: Comes on FC A
P1EFF14 Radiator Rotary Valve Circuit 4 Circuit Short to Ground or Open No +B low voltage when ignition switch is ON, output is off at all the 4 terminals of the FC cooling water temperature control valve step motor, or the WRB2 terminal is judged as abnormal for 1 second or more while the motor is running.
(1 trip detection logic)
·

FC cooling water temperature control valve

·

FC control ECU

·

FC-B relay

·

Wire harness or connector


Master Warning: Comes on FC A

Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List
"FC Work Mode"
Stop Startup Working Finishing
Data List
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection ○ ○ ○ ○ ○ -

Related Data List (EV)
DTC No. Data List
P1DD514 Radiator Rotary Valve Position
P1EFD14
P1EFE14
P1EFF14

Related Active Test (EV)
DTC No. Active Test
P1DD514 Control the Radiator Rotary Valve
P1EFD14
P1EFE14
P1EFF14

WIRING DIAGRAM

A492223E03
0.51,0.521 1.479,0.719 0.969,0.198 10 false FC-B NO. 1 1.781,1 2.698,1.198 0.917,0.198 10 false FC-B 0.552,3.813 1.125,4.219 0.573,0.406 10 false Auxiliary Battery 2.333,0.25 2.51,0.448 0.177,0.198 10 false 5 2.333,0.625 2.51,0.823 0.177,0.198 10 false 1 1.521,0.271 1.698,0.469 0.177,0.198 10 false 3 1.521,0.635 1.698,0.833 0.177,0.198 10 false 2 3.083,3.51 3.469,3.771 0.385,0.26 10 false B1 4.781,3.354 5.167,3.635 0.385,0.281 10 false A48 4.792,2.583 5.167,2.896 0.375,0.313 10 false A48 4.792,1.833 5.146,2.115 0.354,0.281 10 false A48 4.802,1.073 5.229,1.375 0.427,0.302 10 false A48 3.385,3.531 4.302,3.729 0.917,0.198 10 false E1 4.281,3.26 5.198,3.458 0.917,0.198 10 false WRB2 4.292,2.5 5.208,2.698 0.917,0.198 10 false WRB1 4.302,0.969 5.219,1.167 0.917,0.198 10 false WRA1 4.292,1.729 5.208,1.927 0.917,0.198 10 false WRA2 4.885,0.906 5.156,1.104 0.271,0.198 10 false 8 4.865,1.667 5.135,1.865 0.271,0.198 10 false 7 4.885,2.427 5.156,2.625 0.271,0.198 10 false 5 4.875,3.188 5.146,3.385 0.271,0.198 10 false 4 3.052,3.323 3.323,3.521 0.271,0.198 10 false 104 5.458,0.26 5.635,0.458 0.177,0.198 10 false 2 5.458,0.615 5.635,0.813 0.177,0.198 10 false 5 5.448,0.99 5.625,1.188 0.177,0.198 10 false 3 5.635,0.271 6.583,0.479 0.948,0.208 10 false +B1 5.635,0.615 6.583,0.823 0.948,0.208 10 false +B2 5.635,0.979 6.552,1.177 0.917,0.198 10 false WRA1 5.635,1.74 6.552,1.938 0.917,0.198 10 false WRA2 5.635,2.5 6.552,2.698 0.917,0.198 10 false WRB1 5.646,3.26 6.563,3.458 0.917,0.198 10 false WRB2 5.458,2.5 5.635,2.708 0.177,0.208 10 false 6 5.438,3.26 5.615,3.458 0.177,0.198 10 false 4 5.458,1.74 5.635,1.948 0.177,0.208 10 false 1 5.271,3.708 6.188,3.906 0.917,0.198 10 false B17 5.26,3.875 7.146,4.479 1.885,0.604 10 false FC Cooling Water Temperature Control Valve 3.573,4.24 4.646,4.438 1.073,0.198 10 false FC Control ECU 1.292,2.802 2.417,3.125 1.125,0.323 10 false EV Control ECU 1.865,2.146 2.344,2.406 0.479,0.26 10 false MREL 2.354,2.01 2.531,2.208 0.177,0.198 10 false 21 0.375,0.906 1.354,1.125 0.979,0.219 10 false R/B-B NO. 1 0.375,1.458 1.354,1.677 0.979,0.219 10 false R/B FR 1.302,2.625 1.781,2.885 0.479,0.26 10 false A8*1 2.615,0.521 3.583,0.719 0.969,0.198 10 false FC-B NO. 3 1.688,2.625 2.167,2.885 0.479,0.26 10 false D15*2 1.125,4.406 2.01,4.646 0.885,0.24 10 false *1: for LHD 1.938,4.406 2.823,4.646 0.885,0.24 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON and wait for 1 second or more.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FC COOLING WATER TEMPERATURE CONTROL VALVE)

Pre-procedure1

a.
A476958

Disconnect the FC cooling water temperature control valve connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B17)Location & Routing

Click Connector(B17)Engine Compartment>No. 2 Stack Wire>FC Cooling Water Temperature Control Valve

B17-2 (+B1) - Body ground Ignition switch ON 11 to 14 V
B17-5 (+B2) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the FC cooling water temperature control valve connector.



OK

2.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - FC COOLING WATER TEMPERATURE CONTROL VALVE)

NG

5.CHECK HARNESS AND CONNECTOR (FC COOLING WATER TEMPERATURE CONTROL VALVE - FC-B RELAY)
2.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - FC COOLING WATER TEMPERATURE CONTROL VALVE)

Pre-procedure1

a.

Disconnect the FC control ECU connector.


b.

Disconnect the FC cooling water temperature control valve connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A48,B17)Location & Routing

Click Connector(A48)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>FC Control ECU

Click Connector(B17)Engine Compartment>No. 2 Stack Wire>FC Cooling Water Temperature Control Valve

A48-8 (WRA1) - B17-3 (WRA1) Always Below 1 Ω
A48-7 (WRA2) - B17-1 (WRA2) Always Below 1 Ω
A48-5 (WRB1) - B17-6 (WRB1) Always Below 1 Ω
A48-4 (WRB2) - B17-4 (WRB2) Always Below 1 Ω
A48-8 (WRA1) or B17-3 (WRA1) - Body ground and other terminals Always 10 kΩ or higher
A48-7 (WRA2) or B17-1 (WRA2) - Body ground and other terminals Always 10 kΩ or higher
A48-5 (WRB1) or B17-6 (WRB1) - Body ground and other terminals Always 10 kΩ or higher
A48-4 (WRB2) or B17-4 (WRB2) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the FC cooling water temperature control valve connector.


b.

Reconnect the FC control ECU connector.



OK

3.INSPECT FC COOLING WATER TEMPERATURE CONTROL VALVE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FC COOLING WATER TEMPERATURE CONTROL VALVE

Click hereEngine / Hybrid System>COOLING>ROTARY VALVE>INSPECTION

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - BODY GROUND)

NG

REPLACE FC COOLING WATER TEMPERATURE CONTROL VALVE

4.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - BODY GROUND)

Pre-procedure1

a.

Disconnect the FC control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B1)Location & Routing

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

B1-104 (E1) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the FC control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (FC COOLING WATER TEMPERATURE CONTROL VALVE - FC-B RELAY)

Pre-procedure1

a.

Disconnect the FC cooling water temperature control valve connector.


b.

Remove the FC-B relay from the No. 1 front compartment relay block.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B17)Location & Routing

Click Connector(B17)Engine Compartment>No. 2 Stack Wire>FC Cooling Water Temperature Control Valve

B17-2 (+B1) - 5 (FC-B relay holder) Always Below 1 Ω
B17-5 (+B2) - 5 (FC-B relay holder) Always Below 1 Ω
B17-2 (+B1), B17-5 (+B2) or 5 (FC-B relay holder) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reinstall the FC-B relay.


b.

Reconnect the FC cooling water temperature control valve connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR