Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1D0E62  Inverter Output Voltage/FC Converter Output Voltage Signal Compare Failure  


DESCRIPTION

The FC boost control ECU detects high voltage after boosting (FVH) using the voltage sensor which is located inside the FC converter assembly. In addition, the motor generator control ECU (MG ECU) detects high voltage after boosting (VH) using the inverter voltage sensor which is located inside the inverter.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1D0E62 Inverter Output Voltage/FC Converter Output Voltage Signal Compare Failure The difference between the inverter voltage after boosting (VH) and the FC converter output
(1 trip detection logic)
·

FC boost control ECU

·

FC stack main relay (FRB)

·

FC stack main relay (FRG)

·

FC precharge junction assembly (FRP)

·

ECU wire sub-assembly

·

No. 1 FC converter wire

·

No. 2 FC converter wire

·

Inverter with converter assembly

·

Wire harness or connector


Master Warning: Comes on FCDC B

Related Data List
DTC No. System Data List
P1D0E62 FCDC FC Converter Output Voltage
EV VH-Voltage after Boosting

WIRING DIAGRAM

Refer to the wiring diagram for the high-voltage circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA649

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

A484004

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side.

Make sure to remove the EV supply battery assembly service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (w/ 1500W Type Voltage Inverter)


·
A341450

After removing the service plug grip from the EV supply battery assembly, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system. After removing the FC converter power outlet cable (inverter with converter assembly) on FC converter side and use the "HIGH-VOLTAGE, DO NOT TOUCH" sign to notify other technicians that you are working on the high-voltage system.

·
A484005

After removal of the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, wait for at least 10 minutes before touching the high-voltage connectors and terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

HINT:

At least 10 minutes are necessary to discharge the high-voltage capacitors inside the inverter with converter assembly and FC stack assembly.


·
A484932

Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL

·

Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.



NOTICE:
·

When reinstalling the service plug grip to the EV supply battery assembly, after lowering the EV supply battery assembly service plug grip 90°, securely slide it until a "click" sound is heard.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PRECAUTION

·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

Turn the ignition switch to ON (READY) and wait for 5 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT (FCDC)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > FCDC > Trouble Codes
50001 493
Result:
Result Proceed to
Only P1D0E62 is output A
P1D0E62 and DTCs other than the DTCs in the table below are output B
P1D0E62 and any DTCs in the table below are output C

Malfunction Content Relevant DTC
Sensor and actuator circuit malfunction P1D1C16 FC Converter Output Voltage Sensor Circuit Voltage Below Threshold
P1D1C17 FC Converter Output Voltage Sensor Circuit Voltage Above Threshold


HINT:

DTC P1D0E62 may be output as a result of the malfunction indicated by the DTCs above.



Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK DTC OUTPUT (EV)

B

2.CHECK DTC OUTPUT (EV)

C

GO TO DTC CHART

2.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
No DTCs in the table below are output A
Any of the DTCs in the table below are output B

Malfunction Content Relevant DTC
Sensor and actuator circuit malfunction P1E9011 FC Positive Contactor Control Circuit Short to Ground
P1E9015 FC Positive Contactor Control Circuit Short to Battery or Open
P1E9111 FC Negative Contactor Control Circuit Short to Ground
P1E9115 FC Negative Contactor Control Circuit Short to Battery or Open
P1E9211 FC Precharge Contactor Control Circuit Short to Ground
P1E9215 FC Precharge Contactor Control Circuit Short to Battery or Open


HINT:

DTC P1D0E62 may be output as a result of the malfunction indicated by the DTCs above.



Post-procedure1

a.

Turn the ignition switch off.



A

3.CHECK DTC OUTPUT (EV)

B

GO TO DTC CHART

3.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
No DTCs in the table below are output A
Any of the DTCs in the table below are output B

Malfunction Content Relevant DTC
Sensor and actuator circuit malfunction P1C8349 High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction
P0D2D1C Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range
P1AA900 DC/DC Converter "A" Overcurrent (System Performance)
System malfunction P0D2D16 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Above Threshold
P0C7600 Hybrid/EV Battery System Discharge Time Too Long


HINT:

DTC P1D0E62 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

4.CLEAR DTC

B

4.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > FCDC > Clear DTCs
50002 493
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

5.CLEAR DTC
5.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

6.CHECK DTC OUTPUT (FCDC)
6.CHECK DTC OUTPUT (FCDC)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > FCDC > Trouble Codes
50001 493
Result:
Result Proceed to
No DTCs in the table below are output A
Any of the DTCs in the table below are output B

Malfunction Content Relevant DTC
Sensor and actuator circuit malfunction P1D1C16 FC Converter Output Voltage Sensor Circuit Voltage Below Threshold
P1D1C17 FC Converter Output Voltage Sensor Circuit Voltage Above Threshold


HINT:

DTC P1D0E62 may be output as a result of the malfunction indicated by the DTCs above.



Post-procedure1

a.

Turn the ignition switch off.



A

7.CHECK DTC OUTPUT (EV)

B

GO TO DTC CHART

7.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
No DTCs in the table below are output A
Any of the DTCs in the table below are output B

Malfunction Content Relevant DTC
Sensor and actuator circuit malfunction P1E9011 FC Positive Contactor Control Circuit Short to Ground
P1E9015 FC Positive Contactor Control Circuit Short to Battery or Open
P1E9111 FC Negative Contactor Control Circuit Short to Ground
P1E9115 FC Negative Contactor Control Circuit Short to Battery or Open
P1E9211 FC Precharge Contactor Control Circuit Short to Ground
P1E9215 FC Precharge Contactor Control Circuit Short to Battery or Open


HINT:

DTC P1D0E62 may be output as a result of the malfunction indicated by the DTCs above.



Post-procedure1

a.

Turn the ignition switch off.



A

8.CHECK DTC OUTPUT (EV)

B

GO TO DTC CHART

8.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
No DTCs in the table below are output A
Any of the DTCs in the table below are output B

Malfunction Content Relevant DTC
Sensor and actuator circuit malfunction P1C8349 High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction
P0D2D1C Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range
P1AA900 DC/DC Converter "A" Overcurrent (System Performance)
System malfunction P0D2D16 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Above Threshold
P0C7600 Hybrid/EV Battery System Discharge Time Too Long


HINT:

DTC P1D0E62 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

9.SIMULATION TEST (FCDC)

B

9.SIMULATION TEST (FCDC)

Pre-procedure1

a.

Turn the ignition switch to ON (READY).


b.

Drive the vehicle in a city area under the vehicle and driving conditions based on the recorded freeze frame data for approximately 10 minutes.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



Procedure1

a.

Check for DTCs.

Powertrain > FCDC > Trouble Codes
50001 493
Result:
Result Proceed to
No DTCs in the table below are output A
Any of the DTCs in the table below are output B

Malfunction Content Relevant DTC
Sensor and actuator circuit malfunction P1D1C16 FC Converter Output Voltage Sensor Circuit Voltage Below Threshold
P1D1C17 FC Converter Output Voltage Sensor Circuit Voltage Above Threshold


HINT:

DTC P1D0E62 may be output as a result of the malfunction indicated by the DTCs above.



Post-procedure1

a.

Turn the ignition switch off.



A

10.SIMULATION TEST (EV)

B

GO TO DTC CHART

10.SIMULATION TEST (EV)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
No DTCs in the table below are output A
Any of the DTCs in the table below are output B

Malfunction Content Relevant DTC
Sensor and actuator circuit malfunction P1E9011 FC Positive Contactor Control Circuit Short to Ground
P1E9015 FC Positive Contactor Control Circuit Short to Battery or Open
P1E9111 FC Negative Contactor Control Circuit Short to Ground
P1E9115 FC Negative Contactor Control Circuit Short to Battery or Open
P1E9211 FC Precharge Contactor Control Circuit Short to Ground
P1E9215 FC Precharge Contactor Control Circuit Short to Battery or Open


HINT:

DTC P1D0E62 may be output as a result of the malfunction indicated by the DTCs above.



Post-procedure1

a.

Turn the ignition switch off.



A

11.SIMULATION TEST (EV)

B

GO TO DTC CHART

11.SIMULATION TEST (EV)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
No DTCs in the table below are output A
Any of the DTCs in the table below are output B

Malfunction Content Relevant DTC
Sensor and actuator circuit malfunction P1C8349 High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction
P0D2D1C Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range
P1AA900 DC/DC Converter "A" Overcurrent (System Performance)
System malfunction P0D2D16 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Above Threshold
P0C7600 Hybrid/EV Battery System Discharge Time Too Long


HINT:

DTC P1D0E62 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

12.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

12.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1D0619

Result:
Result Proceed to
OK A
NG (The connector is not connected securely) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector) C



A

13.CHECK FC CONVERTER ASSEMBLY (FC CONVERTER POWER OUTLET CABLE CONNECTION CONDITION)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK FC CONVERTER ASSEMBLY (FC CONVERTER POWER OUTLET CABLE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed to EV supply battery assembly and the FC converter power outlet cable (inverter with converter assembly) is not connected to the FC converter assembly.

NOTICE:

After removing the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.
A476935

Check that the bolts for the FC converter power outlet cable (inverter with converter assembly) are tightened to the specified torque, the FC converter power outlet cable (inverter with converter assembly) is connected securely, and there are no contact problems.

Standard:
Item Specified Condition
Torque 8.0 N*m
82 kgf*cm
71 in.*lbf



b.

Disconnect the FC converter power outlet cable (inverter with converter assembly) from the FC converter assembly.

HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL



c.

Check for arc marks at the terminals for the FC converter power outlet cable (inverter with converter assembly).


Result:
Result Proceed to
The terminals are connected securely and there are no contact problems There are no arc marks A
The terminals are not connected securely and there is a contact problem There are arc marks B
The terminals are connected securely and there are no contact problems There are arc marks
The terminals are not connected securely and there is a contact problem There are no arc marks C


Post-procedure1

a.

Reconnect the FC converter power outlet cable (inverter with converter assembly) to the FC converter assembly.



A

14.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE FC POSITIVE RELAY)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

14.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE FC POSITIVE RELAY)

Pre-procedure1

a.

Turn the ignition switch off and wait for 18 hours or more.

HINT:

Waiting for at least 18 hours is required to discharge the inverter with converter assembly and FC converter assembly to 0 V.



Procedure1

a.

Read the values of the following Data List items while performing Active Test.

Powertrain > EV > Active Test
Active Test Display
Activate the FC Positive Relay
Powertrain > FCDC > Dual Data List
Data List Display
FC Converter Output Voltage
50004 397 14 493 9 1
Result:
Result Proceed to
The value of FC Converter Output Voltage is less than 10 V A
The value of FC Converter Output Voltage is 10 V or more B



Post-procedure1

a.

None



A

15.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE FC POSITIVE RELAY)

B

18.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE FC POSITIVE RELAY)
15.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE FC POSITIVE RELAY)

Pre-procedure1

a.

None


Procedure1

a.

Read the values of the following Data List items while performing Active Test.

Powertrain > EV > Active Test
Active Test Display
Activate the FC Positive Relay
Data List Display
VH-Voltage after Boosting
FC Positive Relay Drive Request
50004 397 14 151,696
Result:
Result Proceed to
The value of VH-Voltage after Boosting is less than 10 V A
The value of VH-Voltage after Boosting is 10 V or more B



Post-procedure1

a.

Turn the ignition switch off.



A

16.CLEAR DTC

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY

16.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > FCDC > Clear DTCs
50002 493
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

17.CHECK DTC OUTPUT (FCDC)
17.CHECK DTC OUTPUT (FCDC)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > FCDC > Trouble Codes
50001 493
OK:

DTC is not output.


Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

18.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE FC POSITIVE RELAY)

Pre-procedure1

a.

None


Procedure1

a.

Read the values of the following Data List items while performing Active Test.

Powertrain > EV > Active Test
Active Test Display
Activate the FC Positive Relay
Data List Display
VH-Voltage after Boosting
FC Positive Relay Drive Request
50004 397 14 151,696
Result:
Result Proceed to
The value of VH-Voltage after Boosting is less than 10 V A
The value of VH-Voltage after Boosting is 10 V or more B



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE FC CONVERTER AND FC STACK ASSEMBLY COMPONENT PARTS

Replace the FC converter and FC stack assembly components listed below.

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL

·

FC boost control ECU

·

FC stack main relay (FRB)

·

FC stack main relay (FRG)

·

FC precharge junction assembly (FRP)

·

ECU wire sub-assembly

·

No. 1 FC converter wire

·

No. 2 FC converter wire


HINT:
·

Refer to the parts location for the FC converter and FC stack assembly components.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PARTS LOCATION

·

Refer to the system description for the parts location of the FC converter and FC stack assembly components.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>SYSTEM DESCRIPTION




B

19.REPLACE FC CONVERTER AND FC STACK ASSEMBLY COMPONENT PARTS
19.REPLACE FC CONVERTER AND FC STACK ASSEMBLY COMPONENT PARTS

Replace the FC converter and FC stack assembly components listed below.

HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL


·

FC boost control ECU

·

FC stack main relay (FRB)

·

FC stack main relay (FRG)

·

FC precharge junction assembly (FRP)

·

ECU wire sub-assembly

·

No. 1 FC converter wire

·

No. 2 FC converter wire


HINT:
·

Refer to the parts location for the FC converter and FC stack assembly components.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PARTS LOCATION

·

Refer to the system description for the parts location of the FC converter and FC stack assembly components.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>SYSTEM DESCRIPTION



Result:
Proceed to
NEXT



NEXT

REPLACE INVERTER WITH CONVERTER ASSEMBLY