Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1DDA4B  FC Converter Phase U Over Temperature  P1DDB4B  FC Converter Phase V Over Temperature  P1DDC4B  FC Converter Phase W Over Temperature  P1DDD4B  FC Converter Phase X Over Temperature  


DESCRIPTION

For the description of the FC converter assembly, refer to the wiring diagram for DTC P1D1C16.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1D1C16

If the temperature of the FC converter assembly becomes abnormal, the FC boost control ECU detects a malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1DDA4B FC Converter Phase U Over Temperature Phase U fail signal is detected. (Overheat)
(1 trip detection logic)
·

Inverter cooling system

·

Cooling fan system

·

FC converter assembly

·

Wire harness or connector


Master Warning: Comes on FCDC B
P1DDB4B FC Converter Phase V Over Temperature Phase V fail signal is detected. (Overheat)
(1 trip detection logic)
·

Inverter cooling system

·

Cooling fan system

·

FC converter assembly

·

Wire harness or connector


Master Warning: Comes on FCDC B
P1DDC4B FC Converter Phase W Over Temperature Phase W fail signal is detected. (Overheat)
(1 trip detection logic)
·

Inverter cooling system

·

Cooling fan system

·

FC converter assembly

·

Wire harness or connector


Master Warning: Comes on FCDC B
P1DDD4B FC Converter Phase X Over Temperature Phase X fail signal is detected. (Overheat)
(1 trip detection logic)
·

Inverter cooling system

·

Cooling fan system

·

FC converter assembly

·

Wire harness or connector


Master Warning: Comes on FCDC B

HINT:
·

These DTCs will be stored when the temperature of the FC converter becomes abnormal.

·

These DTCs will not be stored due to motor or FC air compressor system malfunctions.



Related Data List
DTC No. Data List
P1DDA4B
·

Phase U Temperature 1

·

Phase U Temperature 2


P1DDB4B
·

Phase V Temperature 1

·

Phase V Temperature 2


P1DDC4B
·

Phase W Temperature 1

·

Phase W Temperature 2


P1DDD4B
·

Phase X Temperature 1

·

Phase X Temperature 2



WIRING DIAGRAM

Refer to the wiring diagram for the high-voltage circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA649

Refer to the wiring diagram for the FC boost converter low-voltage circuit.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>ECU Power Source Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

A484004

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side.

Make sure to remove the EV supply battery assembly service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (w/ 1500W Type Voltage Inverter)


·
A341450

After removing the service plug grip from the EV supply battery assembly, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system. After removing the FC converter power outlet cable (inverter with converter assembly) on FC converter side and use the "HIGH-VOLTAGE, DO NOT TOUCH" sign to notify other technicians that you are working on the high-voltage system.

·
A484005

After removal of the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, wait for at least 10 minutes before touching the high-voltage connectors and terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

HINT:

At least 10 minutes are necessary to discharge the high-voltage capacitors inside the inverter with converter assembly and FC stack assembly.


·
A484932

Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL

·

Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.



NOTICE:
·

When reinstalling the service plug grip to the EV supply battery assembly, after lowering the EV supply battery assembly service plug grip 90°, securely slide it until a "click" sound is heard.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PRECAUTION

·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)

·

After the inspection is complete, be sure to replace the FC converter assembly (The FC converter may have been damaged by overheating).



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON.

2.

Enter the following menus: Powertrain / EV / Data List / FC Work Mode, FC Intermittent Operation.

3.

Put the state in park (P), turn the ignition switch to ON (READY) and wait until the FC system is activated (Waiting for at least 2 minutes is required after turning the ignition switch to ON (READY)).

FC system is activated: Data List shows that "FC Work Mode" is "Working" and "FC Intermittent Operation" is "OFF".


4.

Wait at least 15 seconds with the FC system activated.

5.

Drive the vehicle forward with the shift state in drive (D) for 5 m (16 ft.) or more.

6.

Drive the vehicle backward with the shift state in reverse (R) for 5 m (16 ft.) or more.



PROCEDURE

1.CHECK DTC OUTPUT (FCDC)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > FCDC > Trouble Codes
50001 493
Result:
Result Proceed to
Only P1DDA4B, P1DDB4B, P1DDC4B or P1DDD4B is output A
P1DDA4B, P1DDB4B, P1DDC4B or P1DDD4B is output and DTCs other than the DTCs in the table below are output B
P1DDA4B, P1DDB4B, P1DDC4B or P1DDD4B is output and any DTCs in the table below are output C

Malfunction Content Relevant DTC
Microcomputer malfunction P060B16 Internal Control Module A/D Processing Performance Circuit Voltage Below Threshold
P060B1C Internal Control Module A/D Processing Performance Circuit Voltage Out of Range
P060B49 Internal Control Module A/D Processing Performance Internal Electronic Failure
P060B71 Internal Control Module A/D Processing Performance Actuator Stuck
P1F451F FC Converter Control Module Power Relay Sense Circuit Intermittent
Sensor and actuator circuit malfunction P1D1C16 FC Converter Output Voltage Sensor Circuit Voltage Below Threshold
P1D1C17 FC Converter Output Voltage Sensor Circuit Voltage Above Threshold
P1D2017 FC Converter Input Voltage Sensor Circuit Voltage Above Threshold
System malfunction P1D0619 FC Converter Phase U Current Circuit Current Above Threshold
P1D0719 FC Converter Phase V Current Circuit Current Above Threshold
P1D0819 FC Converter Phase W Current Circuit Current Above Threshold
P1D0919 FC Converter Phase X Current Circuit Current Above Threshold
P1D0E62 Inverter Output Voltage/FC Converter Output Voltage Signal Compare Failure
P1D0F62 Cell Monitor Voltage/FC Converter Input Voltage Signal Compare Failure


HINT:

DTC P1DDA4B, P1DDB4B, P1DDC4B or P1DDD4B may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK DTC OUTPUT (EV)

B

2.CHECK DTC OUTPUT (EV)

C

GO TO DTC CHART

2.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
No DTCs in the table below are output A
Any of the DTCs in the table below are output B

Malfunction Content Relevant DTC
Sensor and actuator circuit malfunction P0A9300 Inverter "A" Cooling System Performance
P0C7396 Motor Electronics Coolant Pump "A" Component Internal Failure
P314A31 Motor Electronics Coolant Pump "A" No Signal
System malfunction P0C7600 Hybrid/EV Battery System Discharge Time Too Long


HINT:

DTC P1DDA4B, P1DDB4B, P1DDC4B or P1DDD4B may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

3.CHECK CONNECTOR CONNECTION CONDITION (FC CONVERTER ASSEMBLY CONNECTOR)

B

3.CHECK CONNECTOR CONNECTION CONDITION (FC CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1D0619

Result:
Result Proceed to
OK A
NG (The connector is not connected securely) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector) C



A

4.CHECK COOLING SYSTEM

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK COOLING SYSTEM

NEXT

REPLACE FC CONVERTER ASSEMBLY