Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2021.08
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0455058 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B000213  Driver Frontal Stage 2 Deployment Control circuit open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B000213 Driver Frontal Stage 2 Deployment Control circuit open One of the following conditions is met:
·

The airbag ECU assembly detects an open circuit signal in the driver side squib 2nd step circuit for 2 seconds.

·

A spiral cable sub-assembly malfunction.

·

A horn button assembly (driver side squib 2nd step) malfunction.

·

An airbag ECU assembly malfunction.


·

Wire harness

·

Spiral cable sub-assembly

·

Horn button assembly (driver side squib 2nd step)

·

Airbag ECU assembly


Comes on SRS Airbag A Applicable

WIRING DIAGRAM

C238833E98
5.26,1.698 5.688,1.938 0.427,0.24 10 false D10 5.198,1.188 5.344,1.333 0.146,0.146 10 false 8 5.198,0.375 5.302,0.521 0.104,0.146 10 false 9 3.073,0.365 3.177,0.51 0.104,0.146 10 false 4 3.073,1.198 3.177,1.344 0.104,0.146 10 false 3 1.99,1.198 2.094,1.344 0.104,0.146 10 false 1 1.99,0.375 2.094,0.521 0.104,0.146 10 false 2 5.448,0.479 5.781,0.646 0.333,0.167 10 false D2+ 5.448,1.323 5.948,1.51 0.5,0.188 10 false D2- 2.698,0.365 3.219,0.552 0.521,0.188 10 false D2+ 2.708,1.177 3.188,1.385 0.479,0.208 10 false D2- 5.271,1.854 6.729,2.083 1.458,0.229 10 false Airbag ECU Assembly 2.031,1.708 2.396,1.875 0.365,0.167 10 false D31 0.094,1.719 0.438,1.885 0.344,0.167 10 false z7 2.021,1.844 3.146,2.219 1.125,0.375 10 false Spiral Cable Sub-assembly 0.094,1.875 1.906,2.302 1.813,0.427 10 false Horn Button Assembly (Driver Side Squib 2nd Step)

CAUTION / NOTICE / HINT

NOTICE:
·

When installing the spiral cable sub-assembly and steering wheel, be sure to adjust the spiral cable sub-assembly as it may break if the steering wheel is turned before adjusting the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B000213 is output A
History B000213 is output B


Post-procedure1

a.

None



A

2.CHECK CONNECTION OF CONNECTORS

B

USE SIMULATION METHOD TO CHECK

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

HINT:
·

To perform the simulation method, enter check mode (signal check) with the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

Perform the simulation method while checking the Data List.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST




2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


Procedure1

a.

Check that the connectors are properly connected to the horn button assembly (driver side squib 2nd step), spiral cable sub-assembly and airbag ECU assembly.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS

Pre-procedure1

a.
C371112C01
0.198,0.813 0.51,1.01 0.313,0.198 10 false *1 1.052,1.375 1.365,1.573 0.313,0.198 10 false *3 2.781,1.583 3.094,1.781 0.313,0.198 10 false *2 1.979,0.823 2.292,1.021 0.313,0.198 10 false *4
*1 Horn Button Assembly (Driver Side Squib 2nd Step)
*2 Airbag ECU Assembly
*3 Spiral Cable Sub-assembly
*4 Wire Harness


Disconnect the airbag ECU assembly connector.


b.

Disconnect the spiral cable sub-assembly connector.


c.

Disconnect the horn button assembly (driver side squib 2nd step) connector.


Procedure1

a.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.



b.

Check that the connectors are not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



c.

Check that the short springs of the activation prevention mechanisms of the wire harness connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

4.CHECK HORN BUTTON ASSEMBLY

NG

REPAIR OR REPLACE WIRE HARNESS OR SPIRAL CABLE SUB-ASSEMBLY

4.CHECK HORN BUTTON ASSEMBLY
a.
C411565C06
0.333,2.167 0.75,2.417 0.417,0.25 1.479,2.698 1.688,2.885 1.688,2.885 1.833,2.885 true 1.719,2.229 1.885,2.146 1.885,2.146 1.99,2.146 true 2.344,0.615 2.656,0.771 0.313,0.156 10 false A 0.292,0.865 0.604,1.021 0.313,0.156 10 false *1 2.719,1.281 3.031,1.438 0.313,0.156 10 false *2 1.177,1 1.49,1.156 0.313,0.156 10 false *3 2.042,2.052 2.354,2.208 0.313,0.156 10 false *5 0.365,1.719 0.677,1.875 0.313,0.156 10 false *a 1.906,2.813 2.219,2.969 0.313,0.156 10 false *b 2.188,0.615 2.5,0.771 0.313,0.156 10 false B 1.76,0.625 2.073,0.781 0.313,0.156 10 false C 1.594,0.625 2.104,0.771 0.51,0.146 10 false D 0.76,0.625 1.271,0.771 0.51,0.146 10 false E 0.438,0.625 0.948,0.771 0.51,0.146 10 false F 0.469,2.198 0.781,2.354 0.313,0.156 10 false z7 1.969,0.854 2.281,1.01 0.313,0.156 10 false *4
*1 Horn Button Assembly
*2 Airbag ECU Assembly
*3 Spiral Cable Sub-assembly
*4 Wire Harness
*5 SST
*a Front view of wire harness connector
(to Horn Button Assembly)
*b Color: Black


Connect the D10 airbag ECU assembly connector.


b.

Connect the D31 spiral cable sub-assembly connector.


c.

Connect the white wire side of SST (resistance 2.1 Ω) to connector E (black connector).

CAUTION:

Never connect a tester to the horn button assembly for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

5.CHECK HORN BUTTON ASSEMBLY
5.CHECK HORN BUTTON ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B000213 is not output A
B000213 is output B


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


c.

Disconnect SST from connector E.



A

B

6.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT
6.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT

Pre-procedure1

a.
E441559C07
0.5,2.167 0.917,2.417 0.417,0.25 1.896,2.719 1.708,2.719 1.708,2.719 1.573,2.573 true 2.521,0.531 2.76,0.844 0.24,0.313 10 false A 2.208,0.542 2.448,0.854 0.24,0.313 10 false B 1.76,0.531 2,0.844 0.24,0.313 10 false C 1.604,0.531 1.844,0.844 0.24,0.313 10 false D 0.76,0.542 1,0.854 0.24,0.313 10 false E 0.448,0.542 0.688,0.854 0.24,0.313 10 false F 0.25,1.698 0.698,2.01 0.448,0.313 10 false *a 0.625,2.208 0.875,2.375 0.25,0.167 10 false z7 1.969,2.656 2.417,2.969 0.448,0.313 10 false *b 0.271,0.792 0.5,0.99 0.229,0.198 10 false *1 2.813,1.125 3.26,1.438 0.448,0.313 10 false *2 1.156,0.906 1.604,1.219 0.448,0.313 10 false *3 1.927,0.76 2.375,1.073 0.448,0.313 10 false *4
*1 Horn Button Assembly (Driver Side Squib 2nd Step)
*2 Airbag ECU Assembly
*3 Spiral Cable Sub-assembly
*4 Wire Harness
*a Front view of wire harness connector
(to Horn Button Assembly (Driver Side Squib 2nd Step))
*b Color: Black


Disconnect the D10 airbag ECU assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z7)Location & Routing

Click Connector(z7)Instrument Panel>other>Driver Side Squib Circuit (Horn Button Assembly) , Spiral Cable Sub-Assembly

z7-2 - z7-1 Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

7.CLEAR DTC

NG

9.CHECK HARNESS AND CONNECTOR
7.CLEAR DTC
a.
C371113C05
0.313,0.823 0.625,1.021 0.313,0.198 10 false *1 2.583,1.583 2.896,1.781 0.313,0.198 10 false *2 1.146,1.344 1.458,1.542 0.313,0.198 10 false *3 1.917,0.802 2.229,1 0.313,0.198 10 false *4
*1 Horn Button Assembly (Driver Side Squib 2nd Step)
*2 Airbag ECU Assembly
*3 Spiral Cable Sub-assembly
*4 Wire Harness


Connect the airbag ECU assembly connector.


b.

Connect the horn button assembly (driver side squib 2nd step) connector.


c.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

8.CHECK DTC
8.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B000213 is not output A
B000213 is output B


Post-procedure1

a.

None



A

USE SIMULATION METHOD TO CHECK

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

HINT:
·

To perform the simulation method, enter check mode (signal check) with the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

Perform the simulation method while checking the Data List.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST




B

9.CHECK HARNESS AND CONNECTOR

Pre-procedure1

a.
C413909C15
0.406,2.26 0.823,2.51 0.417,0.25 1.25,2.948 1.375,2.948 1.375,2.948 1.521,2.594 true 1.875,2.969 1.74,2.969 1.74,2.969 1.708,2.583 true 0.24,0.802 0.552,1 0.313,0.198 10 false *1 1.99,0.76 2.302,0.958 0.313,0.198 10 false *4 2.802,1.125 3.115,1.323 0.313,0.198 10 false *2 1.094,0.896 1.406,1.094 0.313,0.198 10 false *3 0.354,1.646 0.667,1.844 0.313,0.198 10 false *a 0.958,2.885 1.313,3.073 0.354,0.188 10 false D2- 1.99,2.885 2.323,3.083 0.333,0.198 10 false D2+ 0.5,2.302 0.896,2.5 0.396,0.198 10 false D31 2.531,0.542 2.844,0.74 0.313,0.198 10 false A 2.26,0.552 2.573,0.75 0.313,0.198 10 false B 1.802,0.563 2.115,0.76 0.313,0.198 10 false C 1.531,0.552 1.844,0.75 0.313,0.198 10 false D 0.698,0.552 1.01,0.75 0.313,0.198 10 false E 0.458,0.542 0.771,0.74 0.313,0.198 10 false F
*1 Horn Button Assembly (Driver Side Squib 2nd Step)
*2 Airbag ECU Assembly
*3 Spiral Cable Sub-assembly
*4 Wire Harness
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)


Disconnect the spiral cable sub-assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D31)Location & Routing

Click Connector(D31)Instrument Panel>Instrument Panel Wire>Spiral Cable Sub-Assembly

D31-4 (D2+) - D31-3 (D2-) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR