| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | VOLTAGE INVERTER BRACKET | 86247A | ( )
|
- | - |
| 2 | VOLTAGE INVERTER | 8624A | ( )
|
- | - |
| *1 | UPPER INVERTER COVER | *2 | NO. 2 LUGGAGE ROOM WIRE |
| *3 | SOCKET INVERTER WIRE | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 3 | LUGGAGE COMPARTMENT TRIM COVER INNER RH | 64721 | - | - | - |
| 4 | LUGGAGE COMPARTMENT TRIM COVER INNER LH | 64722 | - | - | - |
| 5 | REAR FLOOR FINISH PLATE | 58387 | - | - | - |
| 6 | FRONT LUGGAGE COMPARTMENT TRIM COVER | 64075B | - | - | - |
| 7 | TOOL BOX | 75201A | - | - | - |
| 8 | LUGGAGE COMPARTMENT TRIM COVER LH | 64715D | - | - | - |
| 9 | LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY | 64701 | - | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 10 | FC CONVERTER POWER OUTLET CABLE (INVERTER WITH CONVERTER ASSEMBLY) | G9200A | ( )
|
- | - |
| 11 | FC STACK COVER SUB-ASSEMBLY | 1A906 | - | - | - |
| 12 | UPPER RADIATOR SUPPORT SEAL | 53292A | - | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 13 | SERVICE PLUG GRIP | G3834 | - | - | - |
86247A
1.INSTALL VOLTAGE INVERTER BRACKET
|
|
8624A
2.INSTALL VOLTAGE INVERTER
|
|
| *1 | No. 2 Luggage Room Wire | *2 | Socket Inverter Wire |
| *a | Green Lock | - | - |
|
Bolt |
|
Connector |
|
High Voltage Connector |
|
Nut |
|
Lock Direction | - | - |
Install the voltage inverter to the upper inverter cover with the 4 bolts.
Attach the clamp and install the No. 2 luggage room wire to the upper inverter cover.
Install the upper inverter cover to the voltage inverter bracket with the 4 nuts.
Connect the No. 2 luggage room wire connector.
Remove the vinyl tape wrapped around the high voltage connector of the No. 2 luggage room wire and the high voltage connector of the socket inverter wire.
Connect the high voltage connector of the No. 2 luggage room wire and the high voltage connector of the socket inverter wire as shown in the illustration, and lock the green lock securely.
Make sure that the connector is attached firmly.
Connect the 2 No. 2 luggage room wire connectors and attach the clamp.
Install the 2 bolts.
64721
3.INSTALL LUGGAGE COMPARTMENT TRIM COVER INNER RH
64722
4.INSTALL LUGGAGE COMPARTMENT TRIM COVER INNER LH
58387
5.INSTALL REAR FLOOR FINISH PLATE
64075B
6.INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER
75201A
7.INSTALL TOOL BOX
64715D
8.INSTALL LUGGAGE COMPARTMENT TRIM COVER LH
64701
9.INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY
1A906
11.INSTALL FC STACK COVER SUB-ASSEMBLY
53292A
12.INSTALL UPPER RADIATOR SUPPORT SEAL
G3834
13.INSTALL SERVICE PLUG GRIP