| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | INSPECT NO. 2 EV BATTERY INTAKE FILTER | G92DJB | ( )
|
- | - |
| 2 | NO. 9 EV BATTERY SHIELD PANEL | G92QBA | ( )
|
- | - |
| 3 | EV BATTERY DUCT SUB-ASSEMBLY | G9209C | ( )
|
- | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 8 | VOLTAGE INVERTER BRACKET | 86247A | - | - | - |
| 9 | FLOOR WIRE | 82161 | - | - | |
| 10 | NO. 1 LUGGAGE ROOM WIRE | 82181 | - | - | - |
| 11 | SOCKET INVERTER WIRE | 821H4C | - | - | - |
| *A | w/ Voltage Inverter 1500W Type | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 12 | NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY | 899A0B | ( )
|
- | - |
| 13 | CLEARANCE WARNING ECU ASSEMBLY | 89340A | - | - | - |
| 14 | STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET | - | - | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 23 | NO. 4 EV BATTERY INTAKE DUCT | G92D4A | - | - | - |
| 24 | NO. 2 EV BATTERY INTAKE DUCT | G92D2A | - | - | - |
| 25 | NO. 1 ROOM PARTITION PAD | 64273D | - | - | - |
| 26 | REAR SEAT SIDE GARNISH LH | 62552F | - | - | - |
| 27 | REAR SEAT SIDE GARNISH RH | 62551F | - | - | - |
| 28 | BENCH TYPE REAR SEATBACK ASSEMBLY | - | - | - | - |
| 29 | REAR DOOR SCUFF PLATE INSIDE LH | 67918F | - | - | - |
| 30 | REAR DOOR SCUFF PLATE INSIDE RH | 67917F | - | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 31 | LUGGAGE COMPARTMENT TRIM COVER INNER RH | 64721 | - | - | - |
| 32 | LUGGAGE COMPARTMENT TRIM COVER INNER LH | 64722 | - | - | - |
| 33 | REAR FLOOR FINISH PLATE | 58387 | - | - | - |
| 34 | FRONT LUGGAGE COMPARTMENT TRIM COVER | 64075B | - | - | - |
| 35 | TOOL BOX | 75201A | - | - | - |
| 36 | LUGGAGE COMPARTMENT TRIM COVER LH | 64715D | - | - | - |
| 37 | LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY | 64701 | - | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 38 | FC CONVERTER POWER OUTLET CABLE (INVERTER WITH CONVERTER ASSEMBLY) | G9200A | ( )
|
- | - |
| *A | If the FC converter power outlet front holder and FC converter power outlet front gasket are left in the stack, remove them using the following procedure | - | - |
| *1 | FC CONVERTER POWER OUTLET FRONT HOLDER | *2 | FC CONVERTER POWER OUTLET FRONT GASKET |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 38 | FC CONVERTER POWER OUTLET CABLE (INVERTER WITH CONVERTER ASSEMBLY) | G9200A | ( )
|
- | - |
| 39 | FC STACK COVER SUB-ASSEMBLY | 1A906 | - | - | - |
| 40 | UPPER RADIATOR SUPPORT SEAL | 53292A | - | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 41 | SERVICE PLUG GRIP | G3834 | - | - | - |
| 42 | PERFORM UTILITY | - | - | - | ( )
|
G92DJB
1.INSPECT NO. 2 EV BATTERY INTAKE FILTER
G92QBA
2.INSTALL NO. 9 EV BATTERY SHIELD PANEL
|
|
G9209C
3.INSTALL EV BATTERY DUCT SUB-ASSEMBLY
|
|
G9510B
4.TEMPORARILY TIGHTEN EV SUPPLY BATTERY ASSEMBLY
|
|
Place wooden blocks as shown in the illustration and install the EV supply battery assembly by sliding it on the wooden blocks.
To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.
Use cardboard or another similar material to protect the EV supply battery assembly and vehicle body from damage.
Since the EV supply battery assembly is very heavy, 2 people are needed to remove it. When removing the HV battery, be careful not to damage the parts around it.
When removing/installing/moving the EV supply battery assembly, make sure not to tilt it more than 80°.
If the EV supply battery assembly has been struck or dropped, replace it.
Temporarily install the EV supply battery assembly to the vehicle body with the 3 bolts.
Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the EV supply battery assembly.
G928BA
5.INSTALL EV BATTERY BRACKET LH
|
|
G928AA
6.INSTALL EV BATTERY BRACKET RH
|
|
G9510B
7.TIGHTEN EV SUPPLY BATTERY ASSEMBLY
|
|
Tighten the 3 bolts.
86247A
8.INSTALL VOLTAGE INVERTER BRACKET (w/ Voltage Inverter 1500W Type)
82161
9.INSTALL FLOOR WIRE
82181
10.INSTALL NO. 1 LUGGAGE ROOM WIRE
| *a | Bolt | *b | Nut |
821H4C
11.INSTALL SOCKET INVERTER WIRE (w/ Voltage Inverter 1500W Type)
|
|
| *1 | Fuse Box | - | - |
| *a | Green-colored Lock | - | - |
|
Slide | - | - |
Connect the connector and slide the green-colored lock as shown in the illustration to lock it securely.
Engage the 2 clamps and install the socket inverter wire to the EV supply battery assembly.
Engage the claw and connect the fuse box.
Connect the 2 connectors.
Install the nut.
89340A
13.INSTALL CLEARANCE WARNING ECU ASSEMBLY
14.INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET
G92F4A
15.INSTALL NO. 4 EV BATTERY EXHAUST DUCT
821H1
16.CONNECT FLOOR UNDER WIRE
|
|
G92QCA
17.INSTALL NO. 10 EV BATTERY SHIELD PANEL
|
|
G9295B
18.INSTALL BATTERY COVER LOCK STRIKER
|
|
| *1 | Battery Cover Lock Striker | - | - |
| *a | Button | *b | Push |
Install the battery cover lock striker, then push the button to lock it.
64227A
19.INSTALL CENTER NO. 1 FLOOR TO BLACE EXTENSION
82161
20.CONNECT FLOOR WIRE
|
|
G92P6A
21.INSTALL NO. 2 EV BATTERY CLAMP COVER
|
|
64228A
22.INSTALL CENTER NO. 2 FLOOR TO BRACE EXTENSION
G92D4A
23.INSTALL NO. 4 EV BATTERY INTAKE DUCT
G92D2A
24.INSTALL NO. 2 EV BATTERY INTAKE DUCT
64273D
25.INSTALL NO. 1 ROOM PARTITION PAD
62552F
26.INSTALL REAR SEAT SIDE GARNISH LH
62551F
27.INSTALL REAR SEAT SIDE GARNISH RH
28.INSTALL BENCH TYPE REAR SEATBACK ASSEMBLY
67918F
29.INSTALL REAR DOOR SCUFF PLATE INSIDE LH
67917F
30.INSTALL REAR DOOR SCUFF PLATE INSIDE RH
64721
31.INSTALL LUGGAGE COMPARTMENT TRIM COVER INNER RH
64722
32.INSTALL LUGGAGE COMPARTMENT TRIM COVER INNER LH
58387
33.INSTALL REAR FLOOR FINISH PLATE
64075B
34.INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER
75201A
35.INSTALL TOOL BOX
64715D
36.INSTALL LUGGAGE COMPARTMENT TRIM COVER LH
64701
37.INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY
G9200A
38.CONNECT FC CONVERTER POWER OUTLET CABLE (INVERTER WITH CONVERTER ASSEMBLY)
|
|
If the front holder and gasket are removed, install them using the following procedure.
Install the gasket to the housing.
Install by aligning the protrusion of the gasket with the housing groove.
Install the front holder to the housing.
Push in the front holder until a "click" sound is heard. After pushing it in, check that it is not removed.
Connect the FC converter power outlet cable (inverter with converter assembly) to the FC converter.
Tighten the 2 bolts (A) and bolt (B) in the order shown in the illustration.
Installing the bolts in an incorrect order may damage the FC converter and FC converter power outlet cable (inverter with converter assembly).
Engage the clamp.
Install the bolt.
1A906
39.INSTALL FC STACK COVER SUB-ASSEMBLY
53292A
40.INSTALL UPPER RADIATOR SUPPORT SEAL
G3834
41.INSTALL SERVICE PLUG GRIP
42. PERFORM UTILITY
|
|