w/ Adaptive High Beam System:
The forward recognition camera communicates with the millimeter wave radar sensor assembly and headlight ECU sub-assembly LH via CAN communication. If a communication malfunction between the forward recognition camera and millimeter wave radar sensor assembly is detected, DTC U023587 is stored.
w/o Adaptive High Beam System:
The forward recognition camera communicates with the millimeter wave radar sensor assembly via CAN communication. If a communication malfunction between the forward recognition camera and millimeter wave radar sensor assembly is detected, DTC U023587 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| U023587 | Lost Communication with Cruise Control Front Distance Range Sensor Signal Sensor or Center Missing Message | Once 3 seconds elapse after turning the ignition switch to ON, a communication malfunction between the millimeter wave radar sensor assembly continues for approximately 2 seconds or more. | ·
Harness or connector ·
Headlight ECU sub-assembly LH (w/ Adaptive High Beam System) ·
Forward recognition camera ·
Millimeter wave radar sensor assembly |
Pre-Collision System | A |
If the DTCs are output simultaneously, the inspection area can be narrowed down.
| Pattern | DTC output part name
(Display on GTS) |
Suspected Area (Malfunction Status) | ||||||
|---|---|---|---|---|---|---|---|---|
| Forward Recognition Camera | Millimeter Wave Radar Sensor Assembly | Headlight ECU Sub-assembly LH | ||||||
| Pre-Collision System | Lane Control | Forward Recognition Camera (Front Lighting Control) | Radar Cruise2 | Front Radar Sensor | AFS | |||
| U023587 | U023587 | U018287 | U023587 | U023587 | U010487 | U023A | ||
|
○: DTC is output -: DTC is not output |
||||||||
| Pattern 1 | ○ | ○ | ○ | ○ | ○ | ○ | ○ | Harness or connector (Open or short) |
| Headlight ECU sub-assembly LH (Internal malfunction) | ||||||||
| Millimeter wave radar sensor assembly (Internal malfunction) | ||||||||
| Forward recognition camera (Internal malfunction) | ||||||||
| Pattern 2 | ○ | ○ | ○ | ○ | ○ | - | - | Forward recognition camera (Internal malfunction) |
| Pattern 3 | ○ | ○ | - | ○ | ○ | ○ | - | Harness or connector (Open) |
| Millimeter wave radar sensor assembly (Internal malfunction) | ||||||||
| Pattern 4 | ○ | ○ | - | ○ | ○ | - | - | Millimeter wave radar sensor assembly (Internal malfunction) |
| Pattern | DTC output part name
(Display on GTS) |
Suspected Area (Malfunction Status) | ||||
|---|---|---|---|---|---|---|
| Forward Recognition Camera | Millimeter Wave Radar Sensor Assembly | |||||
| Pre-Collision System | Lane Control | Forward Recognition Camera (Front Lighting Control) | Radar Cruise2 | Front Radar Sensor | ||
| U023587 | U023587 | U023587 | U023587 | U010487 | ||
|
○: DTC is output -: DTC is not output |
||||||
| Pattern 1 | ○ | ○ | ○ | ○ | ○ | Harness or connector (Open or short) |
| Millimeter wave radar sensor assembly (Internal malfunction) | ||||||
| Forward recognition camera (Internal malfunction) | ||||||
| Pattern 2 | ○ | ○ | ○ | ○ | - | Forward recognition camera (Internal malfunction) |
| Millimeter wave radar sensor assembly (Internal malfunction) | ||||||
w/ Adaptive High Beam System
w/o Adaptive High Beam System
When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.
When the millimeter wave radar sensor assembly has been replaced with a new one, it is necessary to perform millimeter wave radar sensor assembly beam axis alignment and to clear the vehicle control history. Before performing the Driving Adjustment, make sure to read Before Starting Driving Adjustment.
Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.
Triangle Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)
Flat Surface Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)
Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One Time Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)
Sequential Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)
Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>DRIVING ADJUSTMENT
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>ADAPTIVE HIGH BEAM SYSTEM>REGISTRATION
When replacing the headlight ECU sub-assembly LH, always replace it with a new one. If a headlight ECU sub-assembly LH which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Check vehicle condition.
| Result | Proceed to |
|---|---|
| w/ Adaptive High Beam System | A |
| w/o Adaptive High Beam System | B |
A
B
Read each DTC and check the diagnosis pattern using the table below.
| Pattern | DTC output part name
(Display on GTS) |
||||||
|---|---|---|---|---|---|---|---|
| Pre-Collision System | Lane Control | Forward Recognition Camera (Front Lighting Control) | Radar Cruise2 | Front Radar Sensor | AFS | ||
| Pattern 1 | U023587 | U023587 | U018287 | U023587 | U023587 | U010487 | U023A |
| Pattern 2 | U023587 | U023587 | U018287 | U023587 | U023587 | - | - |
| Pattern 3 | U023587 | U023587 | - | U023587 | U023587 | U010487 | - |
| Pattern 4 | U023587 | U023587 | - | U023587 | U023587 | - | - |
| Result | Proceed to |
|---|---|
| Pattern 1 | A |
| Pattern 2 | B |
| Pattern 3 | C |
| Pattern 4 | D |
A
B
C
D
Pre-procedure1
Disconnect the A96 headlight ECU sub-assembly LH connector.
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
None
NEXT
Pre-procedure1
None
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| U023587 is not output | A |
| U023587 is output | B |
Post-procedure1
None
A
B
Pre-procedure1
Connect the A96 headlight ECU sub-assembly LH connector.
Disconnect the A86 millimeter wave radar sensor assembly connector.
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
None
NEXT
Pre-procedure1
None
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| U023A is not output | A |
| U023A is output | B |
Post-procedure1
None
A
B
Pre-procedure1
Connect the A86 millimeter wave radar sensor assembly connector.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H6 forward recognition camera connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H6)Location & Routingewd_type=routing;type=c;code=H6 Click Connector(H6)Body>No. 1 Roof Wire>Forward Recognition Cameraewd_type=component;type=c;code=H6;pinno=6,12 |
||
| H6-6 (CANH) - H6-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| H6-6 (CANH) - Body ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H6-12 (CANL) - Body ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H6-6 (CANH) - +B | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H6-12 (CANL) - +B | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A86 millimeter wave radar sensor assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A86)Location & Routingewd_type=routing;type=c;code=A86 |
||
| A86-5 (CA1P) - A86-6 (CA1N) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Read each DTC and check the diagnosis pattern using the table below.
| Pattern | DTC output part name
(Display on GTS) |
||||
|---|---|---|---|---|---|
| Pre-Collision System | Lane Control | Forward Recognition Camera (Front Lighting Control) | Radar Cruise2 | Front Radar Sensor | |
| Pattern 1 | U023587 | U023587 | U023587 | U023587 | U010487 |
| Pattern 2 | U023587 | U023587 | U023587 | U023587 | - |
| Result | Proceed to |
|---|---|
| Pattern 1 | A |
| Pattern 2 | B |
A
B
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H6 forward recognition camera connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H6)Location & Routingewd_type=routing;type=c;code=H6 Click Connector(H6)Body>No. 1 Roof Wire>Forward Recognition Cameraewd_type=component;type=c;code=H6;pinno=6,12 |
||
| H6-6 (CANH) - H6-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| H6-6 (CANH) - Body ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H6-12 (CANL) - Body ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H6-6 (CANH) - +B | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H6-12 (CANL) - +B | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Connect the H6 forward recognition camera connector.
Disconnect the A86 millimeter wave radar sensor assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A86)Location & Routingewd_type=routing;type=c;code=A86 |
||
| A86-5 (CA1P) - A86-6 (CA1N) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| A86-5 (CA1P) - Body ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A86-6 (CA1N) - Body ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A86-5 (CA1P) - +B | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A86-6 (CA1N) - +B | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the H6 forward recognition camera connector.
Procedure1
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
|
Click Location & Routing(H6)Location & Routingewd_type=routing;type=c;code=H6 Click Connector(H6)Body>No. 1 Roof Wire>Forward Recognition Cameraewd_type=component;type=c;code=H6;pinno=6,12 |
|||
| H6-6 (CANH) - H6-12 (CANL) | Ignition switch ON | 1V/DIV., 100μs./DIV. | Pulse generation |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG