Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Inverter Low-voltage Circuit  


DESCRIPTION

The cause of the malfunction may be the low-voltage circuit.

Check whether there is an open circuit in the inverter +B low-voltage power source system or a problem in the communication between the EV control ECU and inverter.

Related Parts Check
Area Inspection
Inverter +B low-voltage power source system check Check for inverter overcurrent malfunction.
Communication malfunction between EV control ECU and MG-ECU inside inverter with converter assembly Check for inverter overcurrent malfunction due to communication malfunction.
Check for short to ground in inverter +B low-voltage power source system -

WIRING DIAGRAM

for LHD:
A489591E01
1.063,4.385 3.51,4.635 2.448,0.25 10 false EV Control ECU 4.021,4.583 6.073,4.781 2.052,0.198 10 false Inverter with Converter Assembly 6.292,1.323 7.104,1.906 0.813,0.583 10 false from IGCT NO. 1 Relay 1.802,0.771 2.01,1.01 0.208,0.24 10 false * 1.802,1.74 1.958,2.073 0.156,0.333 10 false * 1.792,2.708 1.917,3.042 0.125,0.333 10 false * 1.792,3.646 1.948,3.99 0.156,0.344 10 false * 4.75,3.667 5.458,4 0.708,0.333 10 false * 4.76,2.729 5.469,3.063 0.708,0.333 10 false * 4.76,1.76 5.469,2.094 0.708,0.333 10 false * 4.76,0.781 5.469,1.115 0.708,0.333 10 false * 2.292,0.406 3,0.74 0.708,0.333 10 false CLK+ 2.24,1.365 2.948,1.698 0.708,0.333 10 false REQ+ 2.26,1.833 2.969,2.167 0.708,0.333 10 false REQ- 2.24,2.333 2.948,2.667 0.708,0.333 10 false HTM+ 2.26,2.813 2.969,3.146 0.708,0.333 10 false HTM- 2.229,3.302 2.938,3.635 0.708,0.333 10 false MTH+ 2.271,3.781 2.979,4.115 0.708,0.333 10 false MTH- 0.396,3.385 1.104,3.719 0.708,0.333 10 false A17 0.49,3.177 1.198,3.51 0.708,0.333 10 false 4 0.76,3.406 1.469,3.74 0.708,0.333 10 false E1 2.781,0.313 3.135,0.531 0.354,0.219 10 false 12 2.75,0.521 3.104,0.74 0.354,0.219 10 false A16 2.75,0.99 3.104,1.208 0.354,0.219 10 false A16 2.74,1.469 3.094,1.688 0.354,0.219 10 false A16 2.74,1.958 3.094,2.177 0.354,0.219 10 false A16 2.75,2.438 3.104,2.656 0.354,0.219 10 false A16 2.75,2.927 3.104,3.146 0.354,0.219 10 false A16 2.74,3.406 3.094,3.625 0.354,0.219 10 false A16 2.75,3.896 3.104,4.115 0.354,0.219 10 false A16 2.771,0.792 3.125,1.01 0.354,0.219 10 false 13 2.781,1.26 3.135,1.479 0.354,0.219 10 false 14 2.781,1.76 3.135,1.979 0.354,0.219 10 false 15 2.781,2.229 3.135,2.448 0.354,0.219 10 false 10 2.781,2.719 3.135,2.938 0.354,0.219 10 false 11 2.781,3.208 3.135,3.427 0.354,0.219 10 false 16 2.792,3.688 3.146,3.906 0.354,0.219 10 false 17 3.667,0.427 3.99,0.667 0.323,0.24 10 false 14 3.656,0.885 4.01,1.104 0.354,0.219 10 false 13 3.677,1.365 4.031,1.583 0.354,0.219 10 false 34 3.677,1.833 4.031,2.052 0.354,0.219 10 false 33 3.677,2.333 4.031,2.552 0.354,0.219 10 false 23 3.677,2.823 4.031,3.042 0.354,0.219 10 false 22 3.833,3.344 4.188,3.563 0.354,0.219 10 false 3 3.844,3.792 4.198,4.01 0.354,0.219 10 false 2 4.063,0.417 4.771,0.75 0.708,0.333 10 false CLK+ 2.292,0.896 3,1.229 0.708,0.333 10 false CLK- 4.063,0.906 4.771,1.24 0.708,0.333 10 false CLK- 4.063,1.375 4.771,1.708 0.708,0.333 10 false REQ+ 4.063,1.854 4.771,2.188 0.708,0.333 10 false REQ- 4.073,2.344 4.781,2.677 0.708,0.333 10 false HTM+ 4.073,2.844 4.781,3.177 0.708,0.333 10 false HTM- 4.052,3.292 4.76,3.625 0.708,0.333 10 false MTH+ 4.042,3.813 4.75,4.146 0.708,0.333 10 false MTH- 5.458,3.427 6.167,3.76 0.708,0.333 10 false GND1 5.469,3.875 6.177,4.208 0.708,0.333 10 false GND2 5.969,4 6.677,4.333 0.708,0.333 10 false 31 5.958,3.542 6.667,3.875 0.708,0.333 10 false 30 5.646,0.552 6.021,0.823 0.375,0.271 10 false +B 5.594,0.99 5.969,1.26 0.375,0.271 10 false +B2 5.948,0.677 6.271,0.917 0.323,0.24 10 false 10 5.948,1.115 6.271,1.354 0.323,0.24 10 false 11 6.365,0.708 6.854,1.083 0.49,0.375 10 false IGCT NO. 4 6.354,0.406 6.677,0.646 0.323,0.24 10 false 2 6.594,0.396 6.917,0.635 0.323,0.24 10 false 1 0.104,5.385 2.167,5.667 2.063,0.281 10 false *: Approximately 120 Ω 4.031,4.385 4.875,4.573 0.844,0.188 10 false A19

for RHD:
A489591E02
1.063,4.385 3.51,4.635 2.448,0.25 10 false EV Control ECU 4.021,4.583 6.073,4.781 2.052,0.198 10 false Inverter with Converter Assembly 6.302,1.323 7.104,1.906 0.802,0.583 10 false from IGCT NO. 1 Relay 1.802,0.771 2.01,1.01 0.208,0.24 10 false * 1.802,1.74 1.958,2.073 0.156,0.333 10 false * 1.792,2.708 1.917,3.042 0.125,0.333 10 false * 1.792,3.646 1.948,3.99 0.156,0.344 10 false * 4.75,3.667 5.458,4 0.708,0.333 10 false * 4.76,2.729 5.469,3.063 0.708,0.333 10 false * 4.76,1.76 5.469,2.094 0.708,0.333 10 false * 4.76,0.781 5.469,1.115 0.708,0.333 10 false * 2.292,0.406 3,0.74 0.708,0.333 10 false CLK+ 2.24,1.365 2.948,1.698 0.708,0.333 10 false REQ+ 2.26,1.833 2.969,2.167 0.708,0.333 10 false REQ- 2.24,2.333 2.948,2.667 0.708,0.333 10 false HTM+ 2.26,2.813 2.969,3.146 0.708,0.333 10 false HTM- 2.229,3.302 2.938,3.635 0.708,0.333 10 false MTH+ 2.271,3.781 2.979,4.115 0.708,0.333 10 false MTH- 0.396,3.385 1.104,3.719 0.708,0.333 10 false A17 0.49,3.177 1.198,3.51 0.708,0.333 10 false 4 0.76,3.406 1.469,3.74 0.708,0.333 10 false E1 2.781,0.313 3.135,0.531 0.354,0.219 10 false 12 2.75,0.521 3.104,0.74 0.354,0.219 10 false A16 2.75,0.99 3.104,1.208 0.354,0.219 10 false A16 2.74,1.469 3.094,1.688 0.354,0.219 10 false A16 2.74,1.958 3.094,2.177 0.354,0.219 10 false A16 2.75,2.438 3.104,2.656 0.354,0.219 10 false A16 2.75,2.927 3.104,3.146 0.354,0.219 10 false A16 2.74,3.406 3.094,3.625 0.354,0.219 10 false A16 2.75,3.896 3.104,4.115 0.354,0.219 10 false A16 2.771,0.792 3.125,1.01 0.354,0.219 10 false 13 2.781,1.26 3.135,1.479 0.354,0.219 10 false 14 2.781,1.76 3.135,1.979 0.354,0.219 10 false 15 2.781,2.229 3.135,2.448 0.354,0.219 10 false 10 2.781,2.719 3.135,2.938 0.354,0.219 10 false 11 2.781,3.208 3.135,3.427 0.354,0.219 10 false 16 2.792,3.688 3.146,3.906 0.354,0.219 10 false 17 3.667,0.427 3.99,0.667 0.323,0.24 10 false 14 3.656,0.885 4.01,1.104 0.354,0.219 10 false 13 3.677,1.365 4.031,1.583 0.354,0.219 10 false 34 3.677,1.833 4.031,2.052 0.354,0.219 10 false 33 3.677,2.333 4.031,2.552 0.354,0.219 10 false 23 3.677,2.823 4.031,3.042 0.354,0.219 10 false 22 3.833,3.344 4.188,3.563 0.354,0.219 10 false 3 3.844,3.792 4.198,4.01 0.354,0.219 10 false 2 4.063,0.417 4.771,0.75 0.708,0.333 10 false CLK+ 2.292,0.896 3,1.229 0.708,0.333 10 false CLK- 4.063,0.906 4.771,1.24 0.708,0.333 10 false CLK- 4.063,1.375 4.771,1.708 0.708,0.333 10 false REQ+ 4.063,1.854 4.771,2.188 0.708,0.333 10 false REQ- 4.073,2.344 4.781,2.677 0.708,0.333 10 false HTM+ 4.073,2.844 4.781,3.177 0.708,0.333 10 false HTM- 4.052,3.292 4.76,3.625 0.708,0.333 10 false MTH+ 4.042,3.813 4.75,4.146 0.708,0.333 10 false MTH- 5.458,3.427 6.167,3.76 0.708,0.333 10 false GND1 5.469,3.875 6.177,4.208 0.708,0.333 10 false GND2 5.969,4 6.677,4.333 0.708,0.333 10 false 31 5.958,3.542 6.667,3.875 0.708,0.333 10 false 30 5.646,0.552 6.021,0.823 0.375,0.271 10 false +B 5.594,0.99 5.969,1.26 0.375,0.271 10 false +B2 5.948,0.677 6.271,0.917 0.323,0.24 10 false 10 5.948,1.115 6.271,1.354 0.323,0.24 10 false 11 6.365,0.708 6.854,1.083 0.49,0.375 10 false IGCT NO. 4 6.354,0.406 6.677,0.646 0.323,0.24 10 false 2 6.594,0.396 6.917,0.635 0.323,0.24 10 false 1 0.104,5.385 2.167,5.667 2.063,0.281 10 false *: Approximately 120 Ω 4.031,4.385 4.875,4.573 0.844,0.188 10 false A18

CAUTION / NOTICE / HINT

This step is referenced from the procedures for each DTC.

If the inspection results below are normal, perform the next procedure for the referenced DTC.

CAUTION:
·
A340358


·

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the electric vehicle charger assembly.


Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK FUSE (IGCT NO. 4)

Pre-procedure1

a.
A480890C01
1.667,1.063 2.552,0.396 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *1 2.583,0.302 2.896,0.458 0.313,0.156 10 false *2
*1 Luggage Room Relay Block
*2 IGCT NO. 4 Fuse


Remove the IGCT NO. 4 fuse from the Luggage Room Relay Block.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT NO. 4 fuse terminal Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the IGCT NO. 4 fuse.



OK

2.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)

NG

5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - IGCT NO. 4 FUSE)
2.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL



Procedure1

a.
C361311C90
0.042,0.583 0.479,0.948 0.438,0.365 0.042,1.063 0.479,1.427 0.438,0.365 1.802,1.865 2.083,1.365 true 2.521,1.865 2.229,1.365 true 2.24,1.052 2.521,0.552 true 2.073,1.052 1.781,0.552 true 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 1.635,1.885 2.25,2.083 0.615,0.198 10 false GND1 2.385,1.885 3,2.083 0.615,0.198 10 false GND2 1.625,0.375 1.938,0.573 0.313,0.198 10 false +B 2.531,0.385 2.844,0.583 0.313,0.198 10 false +B2 0.146,0.688 0.604,0.885 0.458,0.198 10 false A19 0.156,1.156 0.615,1.354 0.458,0.198 10 false A18 0.542,0.708 0.854,0.906 0.313,0.198 10 false *A 0.542,1.167 0.854,1.365 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A19-30 (GND1) - Body ground Ignition switch off Below 1 Ω
A19-31 (GND2) - Body ground Ignition switch off Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A18-30 (GND1) - Body ground Ignition switch off Below 1 Ω
A18-31 (GND2) - Body ground Ignition switch off Below 1 Ω



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A19-10 (+B) - Body ground Ignition switch ON 11 to 14 V
A19-11 (+B2) - Body ground Ignition switch ON 11 to 14 V

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A18-10 (+B) - Body ground Ignition switch ON 11 to 14 V
A18-11 (+B2) - Body ground Ignition switch ON 11 to 14 V


NOTICE:

Turning the ignition switch to ON (IG) with the inverter with converter assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

3.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

3.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL



c.

Disconnect the A16 EV control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A480891C12
0.135,1.073 0.552,1.406 0.417,0.333 5.208,0.156 5.625,0.49 0.417,0.333 0.135,1.49 0.552,1.823 0.417,0.333 1.167,2.042 1.417,1.49 true 1.99,2.073 1.49,1.5 true 5.458,1.656 5.844,2.031 true 5.417,1.656 5.74,2.281 true 0.802,2.052 1.406,1.406 true 2.5,2.104 1.49,1.417 true 2.5,0.625 1.49,1.271 true 2.156,0.365 1.49,1.188 true 1.635,0.333 1.406,1.198 true 1.417,1.281 0.563,0.813 true 5.385,1.656 5.438,2.427 true 5.344,1.656 5.146,2.25 true 5.885,1.531 5.531,1.656 true 5.865,1.865 5.5,1.656 true 4.917,1.552 5.26,1.656 true 4.958,2.031 5.313,1.656 true 0.552,0.208 0.865,0.365 0.313,0.156 10 false *a 3.531,0.188 3.844,0.344 0.313,0.156 10 false *b 0.229,1.167 0.5,1.365 0.271,0.198 10 false A19 5.302,0.26 5.573,0.458 0.271,0.198 10 false A16 1.01,2.063 1.438,2.271 0.427,0.208 10 false REQ- 4.865,2.25 5.292,2.458 0.427,0.208 10 false REQ- 5.302,2.458 5.729,2.667 0.427,0.208 10 false REQ+ 1.917,2.104 2.344,2.313 0.427,0.208 10 false REQ+ 0.531,2.042 0.958,2.25 0.427,0.208 10 false HTM- 2.521,2.104 2.948,2.313 0.427,0.208 10 false HTM+ 2.573,0.531 3,0.74 0.427,0.208 10 false CLK+ 2.198,0.26 2.625,0.469 0.427,0.208 10 false MTH+ 1.677,0.229 2.104,0.438 0.427,0.208 10 false MTH- 0.229,0.719 0.656,0.927 0.427,0.208 10 false CLK- 5.75,2.313 6.177,2.521 0.427,0.208 10 false CLK- 5.885,2.042 6.313,2.25 0.427,0.208 10 false CLK+ 4.521,1.427 4.948,1.635 0.427,0.208 10 false MTH- 4.615,1.99 5.042,2.198 0.427,0.208 10 false MTH+ 5.927,1.469 6.354,1.677 0.427,0.208 10 false HTM+ 5.938,1.823 6.365,2.031 0.427,0.208 10 false HTM- 0.219,1.573 0.49,1.771 0.271,0.198 10 false A18 0.625,1.177 0.938,1.375 0.313,0.198 10 false *A 0.625,1.563 0.938,1.76 0.313,0.198 10 false *B
*A for LHD *B for RHD
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Rear view of wire harness connector
(to EV Control ECU)


Standard Resistance (Check for Open):
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19,A16)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A19-23 (HTM+) - A16-10 (HTM+) Ignition switch off Below 1 Ω
A19-22 (HTM-) - A16-11 (HTM-) Ignition switch off Below 1 Ω
A19-3 (MTH+) - A16-16 (MTH+) Ignition switch off Below 1 Ω
A19-2 (MTH-) - A16-17 (MTH-) Ignition switch off Below 1 Ω
A19-34 (REQ+) - A16-14(REQ+) Ignition switch off Below 1 Ω
A19-33 (REQ-) - A16-15 (REQ-) Ignition switch off Below 1 Ω
A19-14 (CLK+) - A16-12 (CLK+) Ignition switch off Below 1 Ω
A19-13 (CLK-) - A16-13 (CLK-) Ignition switch off Below 1 Ω
A19-23 (HTM+) or A16-10 (HTM+) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A19-22 (HTM-) or A16-11 (HTM-) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A19-3 (MTH+) or A16-16 (MTH+) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A19-2 (MTH-) or A16-17 (MTH-) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A19-34 (REQ+) or A16-14(REQ+) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A19-33 (REQ-) or A16-15 (REQ-) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A19-14 (CLK+) or A16-12 (CLK+) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A19-13 (CLK-) or A16-13 (CLK-) - Body ground and other terminals Ignition switch off 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18,A16)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A18-23 (HTM+) - A16-10 (HTM+) Ignition switch off Below 1 Ω
A18-22 (HTM-) - A16-11 (HTM-) Ignition switch off Below 1 Ω
A18-3 (MTH+) - A16-16 (MTH+) Ignition switch off Below 1 Ω
A18-2 (MTH-) - A16-17 (MTH-) Ignition switch off Below 1 Ω
A18-34 (REQ+) - A16-14(REQ+) Ignition switch off Below 1 Ω
A18-33 (REQ-) - A16-15 (REQ-) Ignition switch off Below 1 Ω
A18-14 (CLK+) - A16-12 (CLK+) Ignition switch off Below 1 Ω
A18-13 (CLK-) - A16-13 (CLK-) Ignition switch off Below 1 Ω
A18-23 (HTM+) or A16-10 (HTM+) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A18-22 (HTM-) or A16-11 (HTM-) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A18-3 (MTH+) or A16-16 (MTH+) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A18-2 (MTH-) or A16-17 (MTH-) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A18-34 (REQ+) or A16-14(REQ+) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A18-33 (REQ-) or A16-15 (REQ-) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A18-14 (CLK+) or A16-12 (CLK+) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A18-13 (CLK-) or A16-13 (CLK-) - Body ground and other terminals Ignition switch off 10 kΩ or higher



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19,A16)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A19-23 (HTM+) or A16-10 (HTM+) - Body ground Ignition switch ON Below 1 V
A19-22 (HTM-) or A16-11 (HTM-) - Body ground Ignition switch ON Below 1 V
A19-3 (MTH+) or A16-16 (MTH+) - Body ground Ignition switch ON Below 1 V
A19-2 (MTH-) or A16-17 (MTH-) - Body ground Ignition switch ON Below 1 V
A19-34 (REQ+) or A16-14(REQ+) - Body ground Ignition switch ON Below 1 V
A19-33 (REQ-) or A16-15 (REQ-) - Body ground Ignition switch ON Below 1 V
A19-14 (CLK+) or A16-12 (CLK+) - Body ground Ignition switch ON Below 1 V
A19-13 (CLK-) or A16-13 (CLK-) - Body ground Ignition switch ON Below 1 V

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18,A16)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A18-23 (HTM+) or A16-10 (HTM+) - Body ground Ignition switch ON Below 1 V
A18-22 (HTM-) or A16-11 (HTM-) - Body ground Ignition switch ON Below 1 V
A18-3 (MTH+) or A16-16 (MTH+) - Body ground Ignition switch ON Below 1 V
A18-2 (MTH-) or A16-17 (MTH-) - Body ground Ignition switch ON Below 1 V
A18-34 (REQ+) or A16-14(REQ+) - Body ground Ignition switch ON Below 1 V
A18-33 (REQ-) or A16-15 (REQ-) - Body ground Ignition switch ON Below 1 V
A18-14 (CLK+) or A16-12 (CLK+) - Body ground Ignition switch ON Below 1 V
A18-13 (CLK-) or A16-13 (CLK-) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the EV control ECU and inverter with converter assembly connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the A16 EV control ECU connector.


d.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

4.CHECK EV CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK EV CONTROL ECU

Pre-procedure1

a.

Disconnect the A16 EV control ECU connector.


Procedure1

a.
A480892C02
1.469,0.688 1.906,1.01 0.438,0.323 1.333,2.521 1.583,1.448 true 1.865,2.667 1.677,1.438 true 1.583,2.854 1.635,1.438 true 2.313,0.823 1.813,1.448 true 1.198,2.302 1.542,1.438 true 2.042,2.406 1.719,1.438 true 1.5,1.448 1.198,0.844 true 2.135,2.198 1.771,1.458 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.573,0.781 2.031,0.979 0.458,0.198 10 false A16 2.354,0.729 2.969,0.927 0.615,0.198 10 false HTM+ 2.146,2.208 2.76,2.406 0.615,0.198 10 false HTM- 0.823,2.302 1.438,2.5 0.615,0.198 10 false MTH+ 0.844,0.74 1.458,0.938 0.615,0.198 10 false MTH- 1.458,2.896 2.073,3.094 0.615,0.198 10 false REQ+ 1.052,2.531 1.667,2.729 0.615,0.198 10 false REQ- 2.031,2.438 2.646,2.635 0.615,0.198 10 false CLK+ 1.875,2.688 2.49,2.885 0.615,0.198 10 false CLK-
*a Component without harness connected
(EV Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A16)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A16-10 (HTM+) - A16-11 (HTM-) Ignition switch off 80 to 170 Ω
A16-16 (MTH+) - A16-17 (MTH-) Ignition switch off 80 to 170 Ω
A16-14 (REQ+) - A16-15 (REQ-) Ignition switch off 80 to 170 Ω
A16-12 (CLK+) - A16-13 (CLK-) Ignition switch off 80 to 170 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A16 EV control ECU connector.



OK

INVERTER LOW-VOLTAGE CIRCUIT NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

NG

5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - IGCT NO. 4 FUSE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL



Procedure1

a.
C361311C91
1.729,0.229 2.125,0.542 0.396,0.313 1,0.219 1.396,0.531 0.396,0.313 2.229,1.094 2.604,1.896 true 2.083,1.083 1.813,1.896 true 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 1.677,1.906 1.99,2.104 0.313,0.198 10 false +B 2.573,1.906 2.885,2.104 0.313,0.198 10 false +B2 1.083,0.302 1.542,0.5 0.458,0.198 10 false A19 1.823,0.313 2.281,0.51 0.458,0.198 10 false A18 1.458,0.323 1.771,0.521 0.313,0.198 10 false *A 2.177,0.323 2.49,0.521 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A19-10 (+B) - Body ground Ignition switch off 10 kΩ or higher
A19-11 (+B2) - Body ground Ignition switch off 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A18-10 (+B) - Body ground Ignition switch off 10 kΩ or higher
A18-11 (+B2) - Body ground Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

6.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NEXT

REPLACE FUSE (IGCT NO. 4)

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (IGCT NO. 4)