Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Cooling System  


DESCRIPTION

The cause of the malfunction may be the cooling system.

Check whether the grille is blocked, whether coolant is leaking, the EV radiator fan operating condition and whether coolant has frozen.

Related Parts Check
Area Inspection
Grille blockage, coolant amount, coolant hoses, EV radiator fan Check for overheating due to EV cooling system malfunction.
Inverter coolant temperature sensor (built-in inverter) Check for temperature sensor malfunction.
Coolant freezing check Check freeze frame values to determine whether the hybrid coolant was frozen when the DTC was stored.

Related Data List
Data List
·

Inverter Coolant Water Temperature

·

Motor Inverter Temperature

·

Generator Inverter Temperature

·

Boosting Converter Temperature (Upper)

·

Boosting Converter Temperature (Lower)

·

Ambient Temperature



SYSTEM DESCRIPTION

The inverter built inside the PCU and the inverter for the auxiliary pump convert the high-voltage direct current of the EV supply battery into alternating current for the drive motor, FC air compressor with motor, FC cooling water pump or hydrogen recirculation pump. The inverters generate heat during the conversion process. Therefore, the inverters are cooled by a special cooling system consisting of the water with motor pump assembly, the cooling fan, and a radiator. This cooling system is independent of the FC stack cooling system. The EV control ECU monitors the water with motor pump assembly, the cooling fan and cooling system, and detects malfunctions.

A484689C01
4.729,2.052 4.917,1.417 4.917,1.417 5.083,1.417 true 5.677,3.156 5.865,2.521 5.865,2.521 6.031,2.521 true 2.333,3.083 2.5,3.083 2.5,3.083 2.948,3.406 true 5.333,5.542 5.406,6 5.406,6 5.573,6 true 2.323,5.458 1.833,5.917 1.833,5.917 1.667,5.917 true 1.688,1.521 1.99,2.083 1.99,2.083 2.156,2.083 true 5.125,1.344 5.438,1.542 0.313,0.198 10 false *3 6.094,2.458 6.406,2.656 0.313,0.198 10 false *6 2.146,3.021 2.458,3.219 0.313,0.198 10 false *2 5.615,5.906 5.927,6.104 0.313,0.198 10 false *5 1.51,5.833 1.823,6.031 0.313,0.198 10 false *4 2.198,1.979 2.51,2.177 0.313,0.198 10 false *1 0.042,0.01 0.354,0.208 0.313,0.198 10 false *A
*A for LHD - -
*1 Water with Motor Pump Assembly *2 Inverter Reserve Tank Assembly
*3 Inverter with Converter Assembly *4 Radiator Assembly (EV)
*5 FC Air Compressor with Motor Assembly *6 FC Converter Assembly


A480851C03
5.896,3.531 6.083,2.896 6.083,2.896 6.25,2.896 true 4.417,3.365 4.604,2.729 4.604,2.729 4.771,2.729 true 1.771,3.552 1.917,3.073 1.917,3.073 2.083,3.073 true 4.031,5.99 4.104,6.448 4.104,6.448 4.271,6.448 true 0.927,5.802 1.052,6.448 1.052,6.448 1.219,6.448 true 2.833,1.698 2.906,2.156 2.906,2.156 3.073,2.156 true 6.302,2.833 6.615,3.031 0.313,0.198 10 false *3 4.823,2.667 5.135,2.865 0.313,0.198 10 false *6 2.146,3.021 2.458,3.219 0.313,0.198 10 false *2 4.354,6.375 4.667,6.573 0.313,0.198 10 false *5 1.281,6.375 1.594,6.573 0.313,0.198 10 false *4 3.135,2.083 3.448,2.281 0.313,0.198 10 false *1 0.063,0.063 0.375,0.26 0.313,0.198 10 false *A
*A for RHD - -
*1 Water with Motor Pump Assembly *2 Inverter Reserve Tank Assembly
*3 Inverter with Converter Assembly *4 Radiator Assembly (EV)
*5 FC Air Compressor with Motor Assembly *6 FC Converter Assembly


WIRING DIAGRAM

for LHD:
A479462E04
5.844,5.198 7.031,5.542 1.188,0.344 10 false EV Control ECU 5.823,4.698 6.135,4.896 0.313,0.198 10 false E1 5.823,3.99 6.385,4.229 0.563,0.24 10 false MREL 5.823,2.24 6.385,2.479 0.563,0.24 10 false NIWP 5.823,0.74 6.385,0.979 0.563,0.24 10 false IWP 6.573,1.875 6.896,2.146 0.323,0.271 10 false +B 6.708,3.458 7.031,3.729 0.323,0.271 10 false +B 5.479,4.708 5.792,4.906 0.313,0.198 10 false A17 5.552,4.49 5.865,4.688 0.313,0.198 10 false 4 2.74,3.333 3.052,3.531 0.313,0.198 10 false B27 5.51,3.917 5.823,4.115 0.313,0.198 10 false 21 5.469,2.354 5.781,2.552 0.313,0.198 10 false A17 5.469,0.844 5.781,1.042 0.313,0.198 10 false A17 5.51,2.135 5.823,2.333 0.313,0.198 10 false 10 5.5,0.625 5.813,0.823 0.313,0.198 10 false 30 5.104,3.094 5.417,3.292 0.313,0.198 10 false 1 4.719,2.969 5.167,3.219 0.448,0.25 10 false GND 4.698,2.219 5.26,2.458 0.563,0.24 10 false NWP 5.104,2.479 5.417,2.677 0.313,0.198 10 false 2 4.698,0.74 5.26,0.979 0.563,0.24 10 false SWP 5.104,0.958 5.417,1.156 0.313,0.198 10 false 3 3.229,1.365 4.156,1.708 0.927,0.344 10 false Drive Circuit 2.76,0.385 3.323,0.625 0.563,0.24 10 false +BWP 2.563,0.635 2.875,0.833 0.313,0.198 10 false 4 1.646,4.469 2.427,4.802 0.781,0.333 10 false IGCT NO.2 1.792,2.219 2.76,2.438 0.969,0.219 10 false IGCT NO.5 1.865,1.01 2.177,1.208 0.313,0.198 10 false 1 1.875,0.646 2.188,0.844 0.313,0.198 10 false 3 0.417,3.073 1.073,3.26 0.656,0.188 10 false R/B FR 0.583,5.719 1.99,5.979 1.406,0.26 10 false Auxiliary Battery 1.792,5.875 5.958,6.063 4.167,0.188 10 false IWP: Water with Motor Pump Assembly drive duty 1.792,6.323 6.052,6.552 4.26,0.229 10 false NIWP: Water with Motor Pump Assembly speed signal 2.719,3.5 4.813,3.667 2.094,0.167 10 false Water with Motor Pump Assembly 5.479,4.125 5.792,4.323 0.313,0.198 10 false A8 0.417,1.708 1.604,1.896 1.188,0.188 10 false INV W/PMP 1.156,1.25 1.969,1.469 0.813,0.219 10 false INV W/PMP 1.094,0.646 1.406,0.844 0.313,0.198 10 false 5 1.094,1.01 1.406,1.208 0.313,0.198 10 false 2 2.333,3.719 2.646,3.917 0.313,0.198 10 false 5 1.542,3.719 1.854,3.917 0.313,0.198 10 false 3 2.333,4.24 2.646,4.438 0.313,0.198 10 false 2 1.542,4.24 1.854,4.438 0.313,0.198 10 false 1 0.167,1.573 0.479,1.771 0.313,0.198 10 false 2 0.167,1.813 0.479,2.01 0.313,0.198 10 false 1 0.885,3.458 1.198,3.656 0.313,0.198 10 false 1 2.604,2.323 2.917,2.521 0.313,0.198 10 false 1 1.125,3.458 1.438,3.656 0.313,0.198 10 false 2 2.604,2.094 2.917,2.292 0.313,0.198 10 false 2 0.708,3.76 1.448,4.052 0.74,0.292 10 false IGCT NO.2 0.573,4.792 1.583,4.99 1.01,0.198 10 false R/B RR#2 0.417,2.365 1.948,2.563 1.531,0.198 10 false R/B-B NO.1

for RHD:
A479462E06
5.844,5.198 7.031,5.542 1.188,0.344 10 false EV Control ECU 5.823,4.698 6.135,4.896 0.313,0.198 10 false E1 5.823,4.01 6.385,4.25 0.563,0.24 10 false MREL 5.823,2.271 6.385,2.51 0.563,0.24 10 false NIWP 5.823,0.76 6.385,1 0.563,0.24 10 false IWP 6.573,1.875 6.896,2.146 0.323,0.271 10 false +B 6.708,3.458 7.031,3.729 0.323,0.271 10 false +B 5.479,4.708 5.792,4.906 0.313,0.198 10 false A17 5.552,4.49 5.865,4.688 0.313,0.198 10 false 4 2.74,3.333 3.052,3.531 0.313,0.198 10 false B27 5.51,3.917 5.823,4.115 0.313,0.198 10 false 21 5.469,2.354 5.781,2.552 0.313,0.198 10 false A17 5.469,0.844 5.781,1.042 0.313,0.198 10 false A17 5.51,2.135 5.823,2.333 0.313,0.198 10 false 10 5.5,0.625 5.813,0.823 0.313,0.198 10 false 30 5.104,3.094 5.417,3.292 0.313,0.198 10 false 1 4.74,2.979 5.188,3.229 0.448,0.25 10 false GND 4.729,2.25 5.292,2.49 0.563,0.24 10 false NWP 5.104,2.479 5.417,2.677 0.313,0.198 10 false 2 4.729,0.75 5.292,0.99 0.563,0.24 10 false SWP 5.104,0.958 5.417,1.156 0.313,0.198 10 false 3 3.229,1.365 4.156,1.708 0.927,0.344 10 false Drive Circuit 2.76,0.417 3.323,0.656 0.563,0.24 10 false +BWP 2.563,0.635 2.875,0.833 0.313,0.198 10 false 4 1.646,4.469 2.427,4.802 0.781,0.333 10 false IGCT NO.2 1.792,2.219 2.76,2.438 0.969,0.219 10 false IGCT NO.5 1.865,1.01 2.177,1.208 0.313,0.198 10 false 1 1.875,0.646 2.188,0.844 0.313,0.198 10 false 3 0.417,3.073 1.073,3.26 0.656,0.188 10 false R/B FR 0.583,5.719 1.99,5.979 1.406,0.26 10 false Auxiliary Battery 1.792,5.875 5.958,6.063 4.167,0.188 10 false IWP: Water with motor pump assembly drive duty 1.792,6.323 6.052,6.552 4.26,0.229 10 false NIWP: Water with motor pump assembly speed signal 2.729,3.5 4.823,3.667 2.094,0.167 10 false Water with Motor Pump Assembly 5.458,4.115 5.771,4.313 0.313,0.198 10 false D15 0.417,1.708 1.604,1.896 1.188,0.188 10 false INV W/PMP 1.156,1.25 1.969,1.469 0.813,0.219 10 false INV W/PMP 1.094,0.646 1.406,0.844 0.313,0.198 10 false 5 1.094,1.01 1.406,1.208 0.313,0.198 10 false 2 2.333,3.719 2.646,3.917 0.313,0.198 10 false 5 1.542,3.719 1.854,3.917 0.313,0.198 10 false 3 2.333,4.24 2.646,4.438 0.313,0.198 10 false 2 1.542,4.24 1.854,4.438 0.313,0.198 10 false 1 0.167,1.573 0.479,1.771 0.313,0.198 10 false 2 0.167,1.813 0.479,2.01 0.313,0.198 10 false 1 0.885,3.479 1.198,3.677 0.313,0.198 10 false 1 2.594,2.344 2.906,2.542 0.313,0.198 10 false 1 1.125,3.479 1.438,3.677 0.313,0.198 10 false 2 2.594,2.104 2.906,2.302 0.313,0.198 10 false 2 0.708,3.76 1.448,4.052 0.74,0.292 10 false IGCT NO.2 0.615,4.802 1.625,5 1.01,0.198 10 false R/B RR#2 0.448,2.365 1.979,2.563 1.531,0.198 10 false R/B-B NO.1

CAUTION / NOTICE / HINT

This step is referenced from the procedures for each DTC.

If the inspection results below are normal, perform the next procedure for the referenced DTC.

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK VEHICLE CONDITION

Pre-procedure1

a.

Make sure that the front side of the radiator grille is not blocked with anything.


Procedure1

a.

Ask the customer if the front side of the radiator grille was blocked with anything.

Result:
Result Proceed to
Not blocked. A
Is/was blocked. B


HINT:

If the radiator grille is blocked, the inverter coolant temperature will increase and this DTC may be stored.



Post-procedure1

a.

None.



A

2.CHECK QUANTITY OF EV COOLANT

B

IF EQUIPPED, EXPLAIN TO CUSTOMER THAT OPTIONAL COMPONENTS WILL BE REMOVED

2.CHECK QUANTITY OF EV COOLANT

Pre-procedure1

a.

Check the EV coolant level in the inverter reserve tank.


Procedure1

a.

Check for EV coolant leaks.

Result:
Result Proceed to
No leaks are found and the EV coolant level in the inverter reserve tank assembly is above the low line. A
No leaks are found and the EV coolant level in the inverter reserve tank assembly is below the low line. B
EV coolant leaks are evident. C


HINT:
·

After repairing the EV coolant leaks and adding coolant, perform the Active Tests "Activate the Inverter Water Pump" and "Control the Radiator Fan 1" and make sure that there are no malfunctions.

·

If there are signs of coolant leakage around the connecting parts of a hose and the inverter with converter assembly, replace the hose with a new one.




Post-procedure1

a.

None.



A

3.CHECK COOLANT HOSE

B

ADD EV COOLANT

C

INSPECT FOR COOLANT LEAK AND ADD COOLANT

3.CHECK COOLANT HOSE
a.

Check that the cooling system hoses are not kinked or clogged.

OK:

The cooling system hoses are not kinked or clogged.



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE RADIATOR FAN 1)

NG

REPAIR OR REPLACE COOLANT HOSE

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE RADIATOR FAN 1)
a.

Perform the "Control the Radiator Fan 1" Active Test.

Powertrain > EV > Active Test
Tester Display
Control the Radiator Fan 1
50004 397 18
Result:
Result Proceed to
Cooling fan operates A
Cooling fan stops B




A

5.READ VALUE USING GTS (DATA LIST)

B

5.READ VALUE USING GTS (DATA LIST)

Pre-procedure1

a.

Turn the ignition switch off and wait for 1 hour or more.


Procedure1

a.

Read the Data List with the engine stopped.

Powertrain > EV > Data List
Tester Display
Motor Inverter Temperature
Boosting Converter Temperature (Upper)
Boosting Converter Temperature (Lower)
Inverter Coolant Water Temperature
FC Air Compressor Inverter Temperature
50003 397 130,744,745,152,1001
Result:
Result Proceed to
Other than below. A
"Inverter Coolant Water Temperature" value is higher than the displayed temperature of any other Data List item by 20°C (68°F) or more. B


HINT:

The lower limit temperature that can be displayed for "FC Air Compressor Inverter Temperature", "Motor Inverter Temperature", "Boosting Converter Temperature (Upper)" and "Boosting Converter Temperature (Lower)" is 15°C (59°F). The lower limit temperature for "Inverter Coolant Water Temperature" is -40°C (-40°F). The "Inverter Coolant Water Temperature" value displayed on the GTS may be lower than the others, but this is not a malfunction.



Post-procedure1

a.

Turn the ignition switch off.



A

6.CHECK EV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY

6.CHECK EV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397

b.

Read the freeze frame data item Ambient Temperature using the GTS.


c.

Check if the freeze frame data item Ambient Temperature is below the freezing temperature of the EV coolant.

Result:
Result Proceed to
Ambient Temperature value is above freezing temperature of the EV coolant. A
Ambient Temperature value is below freezing temperature of the EV coolant. B


HINT:
·

EV coolant (SLLC) with a 30% concentration freezes at -15°C (5°F) and EV coolant (SLLC) with a 50% concentration freezes at -35°C (-31°F).

·

If the EV coolant freezes in the EV radiator or water with motor pump, the coolant temperature in the water with motor pump assembly rises because the EV coolant cannot circulate. As a result, a DTC may be stored.

·

A DTC is stored when the water with motor pump impeller cannot rotate due to freezing of the EV coolant.

·

If DTCs are output due to freezing of the LLC, the problem symptom cannot be reproduced. Check the LLC replacement history and whether the LLC was frozen based on the ambient temperature when the DTCs were stored.




Post-procedure1

a.

Turn the ignition switch off.



A

COOLING SYSTEM NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

B