Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1805/52    Short in Front Passenger Side Squib Circuit

DTC    B1806/52    Open in Front Passenger Side Squib Circuit

DTC    B1807/52    Short to GND in Front Passenger Side Squib Circuit

DTC    B1808/52    Short to B+ in Front Passenger Side Squib Circuit

for Preparation Click here


DESCRIPTION

The front passenger side squib circuit consists of the center airbag sensor and the front passenger airbag.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front passenger side squib circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1805/52
Center airbag sensor receives a line short signal 5 times from the front passenger side squib circuit during primary check.
  1. Instrument panel wire
  2. Instrument panel wire assembly
  3. Front passenger airbag (Front passenger side squib)
  4. Center airbag sensor
B1806/52
Center airbag sensor receives an open circuit signal from the front passenger side squib circuit for 2 seconds.
  1. Instrument panel wire
  2. Instrument panel wire assembly
  3. Front passenger airbag (Front passenger side squib)
  4. Center airbag sensor
B1807/52
Center airbag sensor receives a short to ground signal from the front passenger side squib circuit for 0.5 seconds.
  1. Instrument panel wire
  2. Instrument panel wire assembly
  3. Front passenger airbag (Front passenger side squib)
  4. Center airbag sensor
B1808/52
Center airbag sensor receives a short to B+ signal from the front passenger side squib circuit for 0.5 seconds.
  1. Instrument panel wire
  2. Instrument panel wire assembly
  3. Front passenger airbag (Front passenger side squib)
  4. Center airbag sensor

WIRING DIAGRAM


H101119E15


INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting the "CHECK MODE" (signal check) with the Techstream (Click here).
  2. After selecting the "CHECK MODE" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (Click here).

1.CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)


    C145423E02
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the front passenger airbag.

  1. Connect SST (resistance 2.1 Ω) to connector E (orange connector).

    CAUTION:
    Never connect SST to the front passenger airbag (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1805, B1806, B1807, B1808 or 52 is not output.

    HINT:
    DTCs other than DTC B1805, B1806, B1807, B1808 or 52 may be output at this time, but they are not related to this check.



OK
REPLACE FRONT PASSENGER AIRBAG ASSEMBLY
NG


2.CHECK CONNECTOR
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector E.

  1. Check that the instrument panel wire connectors (on the front passenger side airbag) are not damaged.

    OK:
    Lock button is not disengaged, and claw of lock is not deformed or damaged.



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE ASSEMBLY
OK


3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT


    C109498E09
  1. Disconnect the connector from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    A20-1 (P+) - Body ground
    Below 1 V
    A20-2 (P-) - Body ground
    Below 1 V

  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    A20-1 (P+) - A20-2 (P-)
    Below 1 Ω
    A20-1 (P+) - Body ground
    1 MΩ or higher
    A20-2 (P-) - Body ground
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    A20-1 (P+) - A20-2 (P-)
    1 MΩ or higher



OK
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
NG


4.CHECK INSTRUMENT PANEL WIRE ASSEMBLY


    C145425E03
  1. Restore the released activation prevention mechanism of connector B to its original position.

  1. Disconnect the instrument panel wire connector from the instrument panel wire assembly.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    IH1-1 (P+) - Body ground
    Below 1 V
    IH1-2 (P-) - Body ground
    Below 1 V

  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    IH1-1 (P+) - IH1-2 (P-)
    Below 1 Ω
    IH1-1 (P+) - Body ground
    1 MΩ or higher
    IH1-2 (P-) - Body ground
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    IH1-1 (P+) - IH1-2 (P-)
    1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE ASSEMBLY
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE