Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1810/53    Short in Driver Side Squib 2nd Step Circuit

DTC    B1811/53    Open in Driver Side Squib 2nd Step Circuit

DTC    B1812/53    Short to GND in Driver Side Squib 2nd Step Circuit

DTC    B1813/53    Short to B+ in Driver Side Squib 2nd Step Circuit

for Preparation Click here


DESCRIPTION

The driver side squib 2nd step circuit consists of the center airbag sensor, the spiral cable and the steering pad.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the driver side squib 2nd step circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1810/53
Center airbag sensor receives a line short signal 5 times from the driver side squib 2nd step circuit during primary check.
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib 2nd step)
  4. Center airbag sensor
B1811/53
Center airbag sensor receives an open signal from the driver side squib 2nd step circuit for 2 seconds.
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib 2nd step)
  4. Center airbag sensor
B1812/53
Center airbag sensor receives a short circuit to ground signal from the driver side 2nd step circuit for 0.5 seconds.
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib 2nd step)
  4. Center airbag sensor
B1813/53
Center airbag sensor receives a short circuit to B+ signal from the driver side squib 2nd step circuit for 0.5 seconds.
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib 2nd step)
  4. Center airbag sensor

WIRING DIAGRAM


H101118E06


INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting the "CHECK MODE" (signal check) with the Techstream (Click here).
  2. After selecting the "CHECK MODE" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (Click here).

1.CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP)
C145426E01
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the steering pad.

  1. Connect SST to the spiral cable connector E (black connector).

    CAUTION:
    Never connect SST to the steering pad (driver side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1810, B1811, B1812, B1813 or 53 is not output.

    HINT:
    DTCs other than DTC B1810, B1811, B1812, B1813 or 53 may be output at this time, but they are not related to this check.



OK
REPLACE STEERING PAD
NG


2.CHECK CONNECTOR
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from the spiral cable.

  1. Check that the spiral cable connector (on the steering pad side) is not damaged.

    OK:
    Lock button is not disengaged, and claw of lock is not deformed or damaged.



NG
REPLACE SPIRAL CABLE
OK


3.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT
C111719E05
  1. Disconnect the connector from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    D2+ - Body ground
    Below 1 V
    D2- - Body ground
    Below 1 V

  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    D2+ - D2-
    Below 1 Ω
    D2+ - Body ground
    1 MΩ or higher
    D2- - Body ground
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    D2+ - D2-
    1 MΩ or higher



OK
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK


4.CHECK INSTRUMENT PANEL WIRE
C110388E39
  1. Restore the released activation prevention mechanism of connector B to its original position.

  1. Disconnect the instrument panel wire connector from the spiral cable.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    A22-4 (D2+) - Body ground
    Below 1 V
    A22-3 (D2-) - Body ground
    Below 1 V

  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    A22-4 (D2+) - A22-3 (D2-)
    Below 1 Ω
    A22-4 (D2+) - Body ground
    1 MΩ or higher
    A22-3 (D2-) - Body ground
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    A22-4 (D2+) - A22-3 (D2-)
    1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE ASSEMBLY
OK

REPLACE SPIRAL CABLE