Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1815/54    Short in Front Passenger Side Squib 2nd Step Circuit

DTC    B1816/54    Open in Front Passenger Side Squib 2nd Step Circuit

DTC    B1817/54    Short to GND in Front Passenger Side Squib 2nd Step Circuit

DTC    B1818/54    Short to B+ in Front Passenger Side Squib 2nd Step Circuit

for Preparation Click here


DESCRIPTION

The front passenger side squib 2nd step circuit consists of the center airbag sensor and the front passenger airbag.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front passenger side squib 2nd step circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1815/54
Center airbag sensor receives a line short signal 5 times from the front passenger side squib 2nd step circuit during primary check.
  1. Instrument panel wire
  2. Instrument panel wire assembly
  3. Front passenger airbag (Front passenger side squib 2nd step)
  4. Center airbag sensor
B1816/54
Center airbag sensor receives an open signal from the front passenger side squib 2nd step circuit for 2 seconds.
  1. Instrument panel wire
  2. Instrument panel wire assembly
  3. Front passenger airbag (Front passenger side squib 2nd step)
  4. Center airbag sensor
B1817/54
Center airbag sensor receives a short to ground signal from the front passenger side squib 2nd step circuit for 0.5 seconds.
  1. Instrument panel wire
  2. Instrument panel wire assembly
  3. Front passenger airbag (Front passenger side squib 2nd step)
  4. Center airbag sensor
B1818/54
Center airbag sensor receives a short to B+ signal from the front passenger side squib 2nd step circuit for 0.5 seconds.
  1. Instrument panel wire
  2. Instrument panel wire assembly
  3. Front passenger airbag (Front passenger side squib 2nd step)
  4. Center airbag sensor

WIRING DIAGRAM


H101119E05


INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting the "CHECK MODE" (signal check) with the Techstream (Click here).
  2. After selecting the "CHECK MODE" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (Click here).

1.CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB 2ND STEP)
C145428E02
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connector to the front passenger airbag.

  1. Connect SST (resistance 2.1 Ω) to connector E (black connector).

    CAUTION:
    Never connect SST to the front passenger airbag (front passenger side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1815, B1816, B1817, B1818 or 54 is not output.

    HINT:
    Codes other than DTC B1815, B1816, B1817, B1818 and 54 may be output at this time, but they are not related to this check.



OK
REPLACE FRONT PASSENGER AIRBAG ASSEMBLY
NG


2.CHECK CONNECTOR
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector E.

  1. Check that the instrument panel wire assembly connector (on the front passenger airbag side) are not damaged.

    OK:
    Lock button is not disengaged, and claw of lock is not deformed or damaged.



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE ASSEMBLY
OK


3.CHECK FRONT PASSENGER SIDE SQUIB 2ND STEP CIRCUIT
C145429E03
  1. Disconnect the connector from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    A21-1 (P2+) - Body ground
    Below 1 V
    A21-2 (P2-) - Body ground
    Below 1 V

  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    A21-1 (P2+) - A21-2 (P2-)
    Below 1 Ω
    A21-1 (P2+) - Body ground
    1 MΩ or higher
    A21-2 (P2-) - Body ground
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    A21-1 (P2+) - A21-2 (P2-)
    1 MΩ or higher



OK
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
NG


4.CHECK INSTRUMENT PANEL WIRE ASSEMBLY


    C145425E04
  1. Restore the released activation prevention mechanism of connector B to its original position.

  1. Disconnect the instrument panel wire connector from the instrument panel wire assembly.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    IH1-4 (P2-) - Body ground
    Below 1 V
    IH1-3 (P2+) - Body ground
    Below 1 V

  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    IH1-4 (P2-) - IH1-3 (P2+)
    Below 1 Ω
    IH1-4 (P2-) - Body ground
    1 MΩ or higher
    IH1-3 (P2+) - Body ground
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    IH1-4 (P2-) - IH1-3 (P2+)
    1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE ASSEMBLY
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE