DTC B1820/55 Short in Front Driver Side - Side Squib Circuit |
DTC B1821/55 Open in Front Driver Side - Side Squib Circuit |
DTC B1822/55 Short to GND in Front Driver Side - Side Squib Circuit |
DTC B1823/55 Short to B+ in Front Driver Side - Side Squib Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1820/55 |
|
|
| B1821/55 |
|
|
| B1822/55 |
|
|
| B1823/55 |
|
|

| 1.CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY LH (FRONT DRIVER SIDE - SIDE SQUIB) |
![]() |
Turn the power switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connector from the front seat side airbag assembly LH.
Connect SST (resistance 2.1 Ω) to connector C.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the power switch ON (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the power switch OFF.
Turn the power switch ON (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK FLOOR WIRE (FRONT DRIVER SIDE - SIDE SQUIB CIRCUIT) |
![]() |
Turn the power switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the SST from connector C.
Disconnect the connectors from the center airbag sensor assembly.
Check for a short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the power switch ON (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| BC1-1 (SFL+) - Body ground | Power switch ON (IG) | Below 1 V |
| BC1-2 (SFL-) - Body ground | Power switch ON (IG) | Below 1 V |
Check for an open in the circuit.
Turn the power switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| BC1-1 (SFL+) - BC1-2 (SFL-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| BC1-1 (SFL+) - Body ground | Always | 1 MΩ or higher |
| BC1-2 (SFL-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| BC1-1 (SFL+) - BC1-2 (SFL-) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 3.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Connect the connectors to the front seat side airbag assembly LH and the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the power switch ON (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the power switch OFF.
Turn the power switch ON (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| OK | ||
| ||