Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1900/73    Short in Front Driver Side Pretensioner Squib Circuit

DTC    B1901/73    Open in Front Driver Side Pretensioner Squib Circuit

DTC    B1902/73    Short to GND in Front Driver Side Pretensioner Squib Circuit

DTC    B1903/73    Short to B+ in Front Driver Side Pretensioner Squib Circuit

for Preparation Click here


DESCRIPTION

The driver side front pretensioner squib circuit consists of the center airbag sensor and the front seat outer belt LH.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front pretensioner squib circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1900/73
Center airbag sensor receives a line short signal 5 times from the driver side front pretensioner squib circuit during primary check.
  1. Floor wire
  2. Front seat outer belt LH (Driver side front pretensioner squib)
  3. Center airbag sensor
B1901/73
Center airbag sensor receives an open signal from the driver side front pretensioner squib circuit for 2 seconds.
  1. Floor wire
  2. Front seat outer belt LH (Driver side front pretensioner squib)
  3. Center airbag sensor
B1902/73
Center airbag sensor receives a short to ground signal from the driver side front pretensioner squib circuit for 0.5 seconds.
  1. Floor wire
  2. Front seat outer belt LH (Driver side front pretensioner squib)
  3. Center airbag sensor
B1903/73
Center airbag sensor receives a short circuit to B+ signal from the driver side front pretensioner squib circuit for 0.5 seconds.
  1. Floor wire
  2. Front seat outer belt LH (Driver side front pretensioner squib)
  3. Center airbag sensor

WIRING DIAGRAM


H101119E19


INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting the "CHECK MODE" (signal check) with the Techstream (Click here).
  2. After selecting the "CHECK MODE" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (Click here).

1.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH (DRIVER SIDE FRONT PRETENSIONER SQUIB)
C130811E01
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the front seat outer belt LH.

  1. Connect SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect SST to the front seat outer belt LH (driver side front pretensioner squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1900, B1901, B1902, B1903 or 73 is not output.

    HINT:
    DTCs other than DTC B1900, B1901, B1902, B1903 or 73 may be output at this time, but they are not related to this check.



OK
REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH
NG


2.CHECK CONNECTOR
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the SST from connector C.

  1. Check that the floor wire connector (on the driver side front seat outer belt) is not damaged.

    OK:
    The lock button is not disengaged, or the claw of the lock is not deformed or damaged.



NG
REPAIR OR REPLACE FLOOR WIRE
OK


3.CHECK FLOOR WIRE (DRIVER SIDE FRONT PRETENSIONER SQUIB CIRCUIT)
C130812E01
  1. Disconnect the connector from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    P22-1 (L+) - Body ground
    Below 1 V
    P22-2 (L-) - Body ground
    Below 1 V

  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    P22-1 (L+) - P22-2 (L-)
    Below 1 Ω
    P22-1 (L+) - Body ground
    1 MΩ or higher
    P22-2 (L-) - Body ground
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    P22-1 (L+) - P22-2 (L-)
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY