Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1905/74    Short in Front Passenger Side Pretensioner Squib Circuit

DTC    B1906/74    Open in Front Passenger Side Pretensioner Squib Circuit

DTC    B1907/74    Short to GND in Front Passenger Side Pretensioner Squib Circuit

DTC    B1908/74    Short to B+ in Front Passenger Side Front Pretensioner Squib Circuit

for Preparation Click here


DESCRIPTION

The front passenger side front pretensioner squib circuit consists of the center airbag sensor and the front seat outer belt RH.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front passenger side front pretensioner squib circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1905/74
Center airbag sensor receives a line short signal 5 times from the front passenger side front pretensioner squib circuit during primary check.
  1. Floor wire No. 2
  2. Front seat outer belt RH (Front passenger side front pretensioner squib)
  3. Center airbag sensor
B1906/74
Center airbag sensor receives an open signal from the front passenger side front pretensioner squib circuit for 2 seconds.
  1. Floor wire No. 2
  2. Front seat outer belt RH (Front passenger side front pretensioner squib)
  3. Center airbag sensor
B1907/74
Center airbag sensor receives a short to ground signal from the front passenger side front pretensioner squib circuit for 0.5 seconds.
  1. Floor wire No. 2
  2. Front seat outer belt RH (Front passenger side front pretensioner squib)
  3. Center airbag sensor
B1908/74
Center airbag sensor receives a short to B+ signal from the front passenger side front pretensioner squib circuit for 0.5 seconds.
  1. Floor wire No. 2
  2. Front seat outer belt RH (Front passenger side front pretensioner squib)
  3. Center airbag sensor

WIRING DIAGRAM


H101119E20


INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting the "CHECK MODE" (signal check) with the Techstream (Click here).
  2. After selecting the "CHECK MODE" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (Click here).

1.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH (FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB)
C109514E13
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the front seat outer belt RH.

  1. Connect SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect SST to the front seat outer belt RH (front passenger side front pretensioner squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the power switch OFF.

  1. Turn the power switch ON (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1905, B1906, B1907, B1908 or 74 is not output.

    HINT:
    DTCs other than DTC B1905, B1906, B1907, B1908 or 74 may be output at this time, but they are not related to this check.



OK
REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH
NG


2.CHECK CONNECTOR
  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the SST from connector C.

  1. Check that the floor wire No. 2 connector (on the front seat outer belt RH side) is not damaged.

    OK:
    Lock button is not disengaged, or the claw of the lock is not deformed or damaged.



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


3.CHECK FLOOR WIRE NO. 2 (FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB CIRCUIT)
C114784E15
  1. Disconnect the connectors from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    P23-1 (R+) - Body ground
    Below 1 V
    P23-2 (R-) - Body ground
    Below 1 V

  1. Turn the power switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    P23-1 (R+) - P23-2 (R-)
    Below 1 Ω
    P23-1 (R+) - Body ground
    1 MΩ or higher
    P23-2 (R-) - Body ground
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    P23-1 (R+) - P23-2 (R-)
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY