Home › ENGINE › 1NZ-FXE ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using Techstream Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading Data List early in troubleshooting is one way to shorten labor time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Turn the power switch ON (READY) and warm up the engine.

  2. Turn the power switch OFF.

  3. Connect Techstream to the DLC3.

  4. Turn the power switch ON (IG).

  5. Turn Techstream ON.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the tester, read items in Data List.


Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Injector (Port)
Injection period of the No. 1 cylinder/
Min.: 0 ms, Max.: 32.64 ms
Idling: 1 to 3 ms
(Inspection mode)
-
IGN Advance
Ignition timing advance for No. 1 cylinder/
Min.: -64 deg., Max.: 63.5 deg.
Idling: BTDC 7 to 15°
(Inspection mode)
-
Calculate Load
Calculated load by ECM/
Min.: 0%, Max.: 100%
  1. Idling: 10 to 20% (Inspection mode)
  2. Running without load (1,500 rpm): 10 to 20%
-
Vehicle Load
Vehicle load:
Min.: 0 %, Max.: 25,700 %
Actual vehicle load
-
MAF
Air flow rate from MAF meter/
Min.: 0 g/sec., Max.: 655.35 g/sec.
Idling: 3 to 7 g/sec. (1,500 rpm)
If the value is approximately 0.0 g/sec.:
  1. Mass air flow meter power source circuit open
  2. VG circuit open or shorted if the value is 160.0 g/sec. or more
  3. E2G circuit open
Engine Speed
Engine speed/
Min.: 0 rpm, Max.: 16,383 rpm
Idling 950 to 1,050 rpm
(when putting the engine in inspection mode)
-
Vehicle Speed
Vehicle speed/
Min.: 0 km/h, Max.: 255 km/h
Actual vehicle speed
Speed indicated on speedometer
Coolant Temp
Engine coolant temperature/
Min.: -40°C, Max.: 140°C
After warming up: 80 to 100°C
(176 to 212°F)
  1. If the value is -40°C (-40°F):
    sensor circuit is open
  2. If the value is 140°C (284°F):
    sensor circuit is shorted
Intake Air
Intake air temperature/
Min.: -40°C, Max.: 140°C
Equivalent to ambient air temperature
  1. If the value is -40°C (-40°F):
    sensor circuit is open
  2. If the value is 140°C (284°F):
    sensor circuit is shorted
Air-Fuel Ratio
Air-fuel ratio:
Min.: 0, Max.: 1.999
During idling: 1,500 rpm
0.8 to 1.2
-
Ambient Temperature
Ambient air temperature/
Min.: -40°C, Max.: 215°C
Equivalent to ambient air temperature
  1. If the value is -40°C:
    sensor circuit is open
  2. If the value is 215°C:
    sensor circuit is shorted
Purge Density Learn Value
Learning value of purge density/
Min.: -50, Max.: 350
-40 to 0%
Idling (Inspection mode)
Service data
Evap Purge Flow
Purge flow/
Min.: 0%, Max.: 102.4%
Idling: 0 to 100%
-
EVAP (Purge) VSV
EVAP (Purge) VSV control duty/
Min.: 0%, Max.: 100%
0 to 100%
During idling: 1,500 rpm
Order signal from ECM
Vapor Pressure Tank
Vapor pressure/
Min.: -4.125 kPa, Max.: 2.125 kPa
Fuel tank cap removed: 0 kPa
Pressure inside fuel tank is monitored by the vapor pressure sensor
Vapor Pressure Pump
Vapor pressure:
Min.: 33.853 kPa, Max.: 125.596 kPa
Approximately 100 kPa:
Power switch ON (IG)
EVAP system pressure monitored by canister pressure sensor
Vapor pressure (calculated)
Vapor pressure (calculated):
Min.: -5.632 kPa, Max.: 715.264 kPa
Approximately 100 kPa:
Power switch ON (IG)
EVAP system pressure monitored by canister pressure sensor
Knock Correct Learn Value
Correction learning value of knocking/
Min.: -64°CA, Max.: 1,984°CA
0 to 22°CA
Driving: 70 km/h (44 mph)
Service data
Knock Feedback Value
Feedback value of knocking/
Min.: -64°CA, Max.: 1,984°CA
-22 to 0°CA
Driving: 70 km/h (44 mph)
Service data
Clutch Current
Clutch current:
Min.: 0 A, Max.: 2.49 A
-
-
Electromagnetic Clutch
Electromagnetic clutch:
ON or OFF
-
-
Accelerator Idle Position
Whether or not accelerator pedal position sensor is detecting idle/
ON or OFF
Idling: ON
(inspection mode)
-
Throttle Fully Close Learn
Throttle valve fully closed
(learned value)
Min.: 0 V, Max.: 5 V
0.4 to 0.8 V
-
Fail Safe Drive
Whether or not fail safe function is executed/ ON or OFF
ETCS has failed: ON
-
Fail Safe Drive (Main CPU)
Whether or not fail safe function is executed/ ON or OFF
ETCS has failed: ON
-
ST1
Starter signal/ ON or OFF
Cranking: ON
-
System Guard
System guard/
ON or OFF
-
ETCS service data
Open Side Malfunction
Open side malfunction/
ON or OFF
-
ETCS service data
Throttle Pos Sensor Output
Absolute throttle position sensor/
Min.: 0%, Max.: 100%
  1. Throttle fully closed: 10 to 24%
  2. Throttle fully open: 36 to 68%
Read the value with intrusive operation (active test)
Throttle Idle Position
Whether or not throttle position sensor is detecting idle/
ON or OFF
Idling: ON
(inspection mode)
-
Throttle Require Position
Throttle requirement position/
Min.: 0 V, Max.: 5 V
Idling: 0.5 to 1.0 V
(Inspection mode)
-
Throttle Sensor Position
Throttle sensor positioning/
Min.: 0%, Max.: 100%
Idling: 10 to 18%
(Inspection mode)
Calculated value based on VTA1
Throttle Sensor Position #2
Throttle sensor positioning #2/
Min.: 0%, Max.: 100%
-
Calculated value based on VTA2
Throttle Position No.1
Throttle position sensor No. 1 output voltage/
Min.: 0 V, Max.: 4.98 V
-
ETCS service data
Throttle Position No.2
Throttle position sensor No. 2 output voltage/
Min.: 0 V, Max.: 4.98 V
-
ETCS service data
Throttle Position No.1
Throttle position No. 1/
Min.: 0 V, Max.: 5 V
  1. Throttle fully closed:
    0.5 to 1.2 V
  2. Throttle fully opened:
    1.8 to 3.4 V
-
Throttle Position No.2
Throttle position No. 2/
Min.: 0 V, Max.: 5 V
  1. Throttle fully closed: 2.0 to 2.9 V
  2. Throttle fully open: 4.3 to 5.2 V
Read the value with intrusive operation (active test)
Throttle Position Command
Throttle position command value/
Min.: 0 V, Max.: 4.9804 V
0.5 to 4.8 V
ETCS service data
Throttle Sens Open Pos #1
Throttle sensor opener position No. 1/
Min.: 0 V, Max.: 4.9804 V
0.6 to 0.9 V
ETCS service data
Throttle Sens Open Pos #2
Throttle sensor opener position No. 2/
Min.: 0 V, Max.: 4.9804 V
2.2 to 2.6 V
ETCS service data
Throttle Sens Open #1(AD)
Throttle sensor opener position No. 1 (AD)/
Min.: 0 V, Max.: 4.9804 V
0.6 to 0.9 V
ETCS service data
Throttle Motor
Whether or not throttle motor control is permitted/ ON or OFF
Idling: ON
(Inspection mode)
Read the value with the power switch ON (Do not start engine)
Throttle Motor Current
Throttle motor current
Min.: 0 A, Max.: 20 A
Idling: 0 to 3.0 A
(Inspection mode)
-
Throttle Motor DUTY
Throttle motor
Min.: 0%, Max.: 100%
Idling: 0.5 to 40%
(Inspection mode)
-
Throttle Motor Current
Throttle motor current
Min.: 0 A, Max.: 19.92 A
Idling: 0 to 3.0 A
-
Throttle Motor Open Duty
Throttle motor opening duty ratio/
Min.: 0%, Max.: 100%
Idling: 0 to 40%
When accelerator pedal is depressed, duty ratio is increased
Throttle Motor Close Duty
Throttle motor closed duty ratio/
Min.: 0%, Max.: 100%
Idling: 0 to 40%
When accelerator pedal is released quickly, duty ratio is increased
Throttle Motor Duty (Open)
Throttle motor duty ratio (open)/
Min.: 0%, Max.: 100%
-
ETCS service data
Throttle Motor Duty (Close)
Throttle motor duty ratio (close)/
Min.: 0%, Max.: 100%
-
ETCS service data
O2S B1 S2
Heated oxygen sensor output voltage for bank 1 sensor 2/
Min.: 0 V, Max.: 1.275 V
Driving: 70 km/h (44 mph)
0.1 to 0.9 V
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor
AFS B1 S1
A/F sensor output voltage for bank 1 sensor 1/
Min.: 0 V, Max.: 7.999 V
Idling: 2.8 to 3.8 V
(Inspection mode)
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor
Total FT #1
Total fuel trim of bank 1:
Average value for fuel trim system of bank 1/
Min.: -0.5, Max.: 0.496
Idling: -0.2 to 0.2
(Inspection mode)
-
Short FT #1
Short-term fuel trim of bank 1/
Min.: -100%, Max.: 99.2%
0 +- 20%
This item is the short-term fuel compensation used to maintain the air-fuel ratio at stoichiometric air-fuel ratio
Long FT #1
Long-term fuel trim of bank 1/
Min.: -100%, Max.: 99.2%
0 +- 20%
This item is the overall fuel compensation carried out in long-term to compensate for a continual deviation of the short-term fuel trim from the central value
Fuel System Status (Bank1)
Fuel system status (Bank 1) / OL or CL or OL DRIVE or OL FAULT or CL FAULT
Idling after warming up: CL
(Inspection mode)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  2. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
  3. OL DRIVE: Open loop due to driving conditions (fuel enrichment)
  4. OL FAULT: Open loop due to detected system fault
  5. CL FAULT: Closed loop but heated oxygen sensor, which is used for fuel control, is malfunctioning
Fuel System Status (Bank2)
Fuel system status:
OL or CL or OL DRIVE or OL FAULT or CL FAULT
-
Not available
O2FT B1 S2
Short-term fuel trim associated with the bank 1 sensor 2/
Min.: -100%, Max.: 99.2%
0 +- 20%
Same as Short FT #1
AF Lambda B1 S1
Short-term fuel trim associated with the bank 1 sensor 1/
Min.: 0, Max.: 1.999
  1. Value less than 1 (0.000 to 0.999) = Rich
  2. Stoichiometric air-fuel ratio = 1
  3. Value greater than 1 (1.001 to 1.999) = Lean
-
Catalyst Temp (B1 S1)
Catalyst temperature (Bank 1, Sensor 1)/
Min.: -40°C, Max.: 6,513.5°C
-
-
Catalyst Temp (B1 S2)
Catalyst temperature (Bank 1, Sensor 2)/
Min.: -40°C, Max.: 6,513.5°C
-
-
Sub O2S Impedance B1S2
Sub O2S impedance B1S2:
Min.:0 Ω, Max.:21247.68 Ω
5 to 15,000 Ω
-
Initial Engine Coolant Temp
Initial engine coolant temperature/ Min.: -40°C, Max.: 120°C
Close to ambient air temperature
Service data
Initial Intake Air Temp
Initial intake air temperature/ Min.: -40°C, Max.: 120°C
Close to ambient air temperature
Service data
Injection Volum (Cylinder1)
Injection volume (cylinder 1)/
Min.: 0 ml, Max.: 2.048 ml
0 to 0.5 ml
Quantity of fuel injection volume for 10 times
Closed Throttle Position SW
Closed throttle position switch:
ON or OFF
  1. ON: Throttle fully closed
  2. OFF: Throttle open
-
Engine Oil Pressure SW
Engine oil pressure switch signal/
0: OFF / 1: ON
Indicating ON while engine is running
-
ETCS Actuator Power
Whether or not electric throttle control system power is input/
ON or OFF
Idling: ON
(inspection mode)
-
+BM Voltage
+BM voltage/
Min.: 0, Max.: 19.92182
Idling: 10 to 15 V
ETCS service data
Battery Voltage
Battery voltage/
Min.: 0 V, Max.: 65.535 V
Idling: 9 to 14 V
(Inspection mode)
-
Actuator Power Supply
Actuator power supply/
ON or OFF
Idling ON
(Inspection mode)
ETCS service data
Atmosphere Pressure
Atmospheric pressure:
Min.: 0 kPa, Max.: 255 kPa
Approximately 100 kPa: Power switch ON (IG)
-
EVAP Purge VSV
VSV status for EVAP control/
ON or OFF
VSV operating: ON
VSV for EVAP is controlled by the ECM (ground side duty control)
Fuel Pump/Speed Status
Fuel pump/speed status/
ON or OFF
Idling: ON
(Inspection mode)
-
VVT Control Status (Bank1)
VVT control status/
ON or OFF
-
Support for VVT active test
Vacuum Pump
Key-off EVAP system leak detection pump status:
ON or OFF
-
Active Test support data
EVAP System Vent Valve
Key-off EVAP system vent valve status:
ON or OFF
-
Active Test support data
Electric Fan Motor
Electric fan motor:
ON or OFF
-
Support for fan motor active test
Tank Bypass VSV
Tank bypass VSV:
ON or OFF
-
Support for tank bypass VSV active test
TC and TE1
TC and TE1 terminal of DLC3:
ON or OFF
-
-
VVT Aim Angle (Bank1)
VVT aim angle (bank 1):
Min.: 0%, Max.: 100%
Idling: 0%
VVT duty signal value during intrusive operation
VVT Change Angle (Bank1)
VVT change angle:
Min.: 0°FR, Max.: 60°FR
Idling: 0 to 5 °FR
Displacement angle during intrusive operation
VVT OCV Duty (Bank1)
VVT OCV operation duty:
Min.: 0%, Max.:100%
Idling: 0%
Requested duty value for intrusive operation
Idle Fuel Cut
Fuel cut idle: ON or OFF
Fuel cut operation: ON
Fuel cut idle = "ON" when throttle valve is fully closed and engine speed is over 2,800 rpm
FC TAU
Fuel cut TAU: Fuel cut during very light load: ON or OFF
Fuel cut operating: ON
The fuel cut is being performed under very light load to prevent incomplete engine combustion
Ignition
Ignition counter: Min.: 0, Max.: 800
0 to 800
-
Cylinder #1 Misfire Count
Misfire ratio of the cylinder 1:
Min.: 0, Max.: 255
0%
This item is displayed only during idling
Cylinder #2 Misfire Count
Misfire ratio of the cylinder 2:
Min.: 0, Max.: 255
0%
This item is displayed only during idling
Cylinder #3 Misfire Count
Misfire ratio of the cylinder 3:
Min.: 0, Max.: 255
0%
This item is displayed only during idling
Cylinder #4 Misfire Count
Misfire ratio of the cylinder 4:
Min.: 0, Max.: 255
0%
This item is displayed only during idling
All Cylinders Misfire Count
All cylinders misfire rate:
Min.: 0, Max.: 255
0 to 35
-
Misfire RPM
Engine RPM for first misfire range:
Min.: 0 rpm, Max.: 6,375 rpm
Misfire 0: 0 rpm
-
Misfire Load
Engine load for first misfire range:
Min.: 0 g/rev, Max.: 3.98 g/rev
Misfire 0: 0 g/rev
-
Misfire Margin
Misfire monitoring:
MIn.: -100%, Max.: 99.22%
-100 to 99.2%
Misfire detecting margin
# Codes
#Codes:
Min.: 0, Max.: 255
-
Number of detected DTCs
Check Mode
Check mode: ON or OFF
Check mode ON: ON
(Click here)
Misfire Test
Check mode result for misfire monitor:
Complete or Incomplete
-
-
OXS1 Test
Check mode result for HO2 sensor:
Complete or Incomplete
-
-
A/F Test Results (Bank1)
Check mode result for air-fuel ratio sensor:
Complete or Incomplete
-
-
MIL
MIL status: ON or OFF
MIL ON: ON
-
MIL ON Run Distance
MIL ON run distance:
Min.: 0 second,
Max.: 65,535 seconds
Distance after DTC is detected
-
Running Time from MIL ON
Running time from MIL ON:
Min.: 0 minute,
Max.: 65,535 minutes
Equivalent to running time after MIL was ON
-
Engine Run Time
Engine run time:
Min.: 0 second,
Max.: 65,535 seconds
Time after engine start
Service data
Time after DTC Cleared
Time after DTC cleared:
Min.: 0 minute,
Max.: 65,535 minutes
Equivalent to time after DTCs were erased
-
Distance from DTC Cleared
Distance after DTC cleared:
Min.: 0 km/h,
Max.: 65535 km
Equivalent to drive distance after DTCs were erased
-
Warmup Cycle Cleard DTC
Warm-up cycle after DTC cleared:
Min.: 0, Max.: 255
-
Number of warm-up cycles after DTC is cleared
OBD Requirements
OBD requirement
OBD2
-
Number of Emission DTC
Emission related DTCs
-
Number of emission related DTCs
Complete Parts Monitor
Comprehensive component monitor:
Not Avl or Avail
-
-
Fuel System Monitor
Fuel system monitor:
Not Avl or Avail
-
-
Misfire Monitor
Misfire monitor:
Not Avl or Avail
-
-
O2S(A/FS) Monitor
O2S (A/FS ) heater monitor:
Not Avl or Avail
-
-
O2S(A/FS) Monitor
O2S (A/FS ) heater monitor:
Complete or Incomplete
-
-
EVAP Monitor
EVAP monitor:
Not Avl or Avail
-
-
EVAP Monitor
EVAP monitor:
Complete or Incomplete
-
-
Catalyst Monitor
Catalyst monitor:
Not Avl or Avail
-
-
Catalyst Monitor
Catalyst monitor:
Complete or Incomplete
-
-
Component Monitor ENA
Comprehensive component monitor:
Unable or Enable
-
-
Component Monitor CMPL
Comprehensive component monitor:
Complete or Incomplete
-
-
Fuel System Monitor ENA
Fuel system monitor:
Unable or Enable
-
-
Fuel System Monitor CMPL
Fuel system monitor:
Complete or Incomplete
-
-
Misfire Monitor ENA
Misfire monitor:
Unable or Enable
-
-
Misfire Monitor CMPL
Misfire monitor:
Complete or Incomplete
-
-
EGR Monitor ENA
EGR monitor:
Unable or Enable
-
-
EGR Monitor CMPL
EGR monitor:
Complete or Incomplete
-
-
Heater Monitor ENA
O2S (A/FS ) heater monitor:
Unable or Enable
-
-
Heater Monitor CMPL
O2S (A/FS ) heater monitor:
Complete or Incomplete
-
-
O2S(A/FS) Monitor ENA
O2S (A/FS ) monitor:
Unable or Enable
-
-
O2S(A/FS) Monitor CMPL
O2S (A/FS ) monitor:
Complete or Incomplete
-
-
A/C Monitor ENA
A/C monitor:
Unable or Enable
-
-
A/C Monitor CMPL
A/C monitor:
Complete or Incomplete
-
-
2nd Air Monitor ENA
2nd air monitor:
Unable or Enable
-
-
2nd Air Monitor CMPL
2nd air monitor:
Complete or Incomplete
-
-
EVAP Monitor ENA
EVAP monitor:
Unable or Enable
-
-
EVAP Monitor CMPL
EVAP monitor:
Complete or Incomplete
-
-
Heated Cat Monitor ENA
Heated catalyst monitor:
Unable or Enable
-
-
Heated Cat Monitor CMPL
Heated catalyst monitor:
Complete or Incomplete
-
-
Catalyst Monitor ENA
Catalyst monitor:
Unable or Enable
-
-
Catalyst Monitor CMPL
Catalyst monitor:
Complete or Incomplete
-
-
Requested Engine Torque
Requested engine torque:
Min.: 0 kW, Max.: 16383.75 kW
0 to 57 kW
Flag information for hybrid vehicle
HV Target Engine Speed
HV target engine speed:
Min.: 0 rpm, Max.: 6375 rpm
0 to 5000 rpm
Flag information for hybrid vehicle
Actual Engine Torque
Actual engine torque:
Min.: -128 Nm, Max.: 127 Nm
-128 to 127 Nm
Flag information for hybrid vehicle
Estimated Engine Torque
Estimated engine torque:
Min.: 0 Nm, Max.: 510 Nm
0 to 120 Nm
Flag information for hybrid vehicle
Engine Run Time
Engine run time:
Min.: 0 second, Max.: 255 seconds
0 to 255 seconds
Flag information for hybrid vehicle
Request Engine Run Time
Request engine run time:
Min.: 0 second,
Max.: 25.5 seconds
0 to 25.5 seconds
Flag information for hybrid vehicle
Judge Time Engine Ignition
Judgment time for ignition of engine:
Min.: 0 second,
Max.: 25.5 seconds
0 to 25.5 seconds
Flag information for hybrid vehicle
Judge Time Engine Output
Judgment time for engine output:
Min.: 0 second,
Max.: 25.5 seconds
0 to 25.5 seconds
Flag information for hybrid vehicle
Estimated Intake Port Temp
Estimated intake port temperature:
Min.: -40°C, Max.: 215°C
80 to 100°C
Flag information for hybrid vehicle
Fuel Level
Fuel level: Empty or Not Emp
-
Flag information for hybrid vehicle
ISC Learning
ISC learning:
Complete or Incomplete
-
-
F/C for Engine Stop Req
Fuel cut for engine stop request:
OFF or ON
-
Flag information for hybrid vehicle
Engine Independent
Engine independently operation:
Not Opr or Operate
-
Flag information for hybrid vehicle
Racing Operation
Rev-up operation:
Not Opr or Operate
-
Flag information for hybrid vehicle
Request Warm-up
Request warm-up:
Not Req or Request
-
Flag information for hybrid vehicle
Engine Independent Control
Engine independently control operation:
Not Opr or Operate
-
Flag information for hybrid vehicle
Tank Outlet Water Temp
CHS tank outlet temperature sensor output:
Min: -40°C, Max: 215°C
-
  1. If the value is -40°C: sensor circuit is open
  2. If the value is 215°C: sensor circuit is shorted

Water Flow Valve
Water valve position signal:
Min: 0 V, Max: 4.98 V
0.45 to 4.6 V
Voltage varies based on valve position
ISC Learning Value
ISC learning value:
Min: 0 L/s, Max: 19.92 L/s
-
Flag information for hybrid vehicle
Direction Value 1
Direction Val Heat Storage 3 way valve (ctrl side):
Min: 0 V, Max: 5 V
2.5 to 4.5 V
-
Direction Value 2
Direction Val Heat Storage 3 way valve (OBD side):
Min: 0 V, Max: 5 V
2.5 to 4.5 V
-
Model Code
Identifying model code
NHW20#
-
Engine Type
Identifying engine type
1NZFXE
-
Cylinder Number
Identifying cylinder number:
Min.: 0, Max.: 255
4
-
Destination
Identifying destination
A (America)
-
Model Year
Identifying model year:
Min.: 1900, Max.: 2155
2008
-
System Identification
Identifying engine system
HV
-

HINT:
*: If no condition is specifically stated for "Idling", it means the transaxle position is N or P, the A/C switch is OFF and all accessory switches are OFF.


ACTIVE TEST

HINT:
Performing Active Test using Techstream or the OBD II scan tool allows the relay, VSV, actuator and so on to operate without parts removal. Performing Active Test as a first step of troubleshooting is one method to shorten diagnostic time.
It is possible to display Data List during Active Test.

  1. Turn the power switch ON (READY) and warm up the engine.

  2. Turn the power switch OFF.

  3. Connect Techstream to the DLC3.

  4. Turn the power switch ON (IG).

  5. Turn Techstream ON.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. According to the display on the tester, perform items in Active Test.


Tester Display
Test Part
Control Range
Control the Injection Volume
[Test Details]
Control the injection volume
Min.: -12.5%, Max.: 24.8%
[Vehicle Condition]
Engine speed: 3,000 rpm or less
  1. All injectors are tested at once
  2. Injection volume is gradually changed between -12 and 25%
Control the Injection Volume for A/F Sensor
[Test Details]
Control the injection volume
-12.5 or 24.8% (Change the injection volume 12.5 % or 25%)
[Vehicle Condition]
Engine speed: 3,000 rpm or less
  1. The following Control the Injection Volume for A/F Sensor procedure enables the technician to check and graph the voltage outputs of both the A/F sensor and heated oxygen sensor
  2. Control the Injection Volume for A/F Sensor enables to check and graph of A/F (Air Fuel Ratio) sensor and Heated Oxygen sensor voltage outputs.
Activate the VSV for Evap Control
[Test Details]
Activate the VSV for EVAP control
ON or OFF
(Click here)
Activate the VSV for Tank Bypass
[Test Details]
Activate the VSV for tank bypass
ON or OFF
(Click here)
Control the Fuel Pump / Speed
[Test Details]
Control the fuel pump
ON or OFF
-
Connect the TC and TE1
[Test Details]
Connect TC and TE1
ON or OFF
-
Control the Idle Fuel Cut Prohibit
[Test Details]
Control the idle fuel cut prohibit
ON or OFF
-
Control the Electric Cooling Fan
[Test Details]
Control the electric cooling fan
ON or OFF
-
Control the ETCS Open/Close Slow Speed
[Test Details]
Control the ETCS opening/closing slow speed
ON or OFF
Throttle valve intrusive operation
Control the ETCS Open/Close Fast Speed
[Test Details]
Control the ETCS opening/closing fast speed
ON or OFF
Throttle valve intrusive operation
Control the VVT Linear (Bank1)
[Test Details]
Control the VVT (bank 1)
Min.: -128%, Max.: 127%
-
Control the VVT System (Bank1)
[Test Details]
Activate the VVT system (Bank 1)
ON or OFF
  1. ON: Rough idle or engine stall
  2. OFF: Normal engine speed
(Click here)
Activate the Water Pump
[Test Details]
Activate the water pump
ON or OFF
Coolant heat storage water pump
Activate the Water Flow Valve 1
[Test Details]
Activate the water valve
ON or OFF
Unused
Activate the Water Flow Valve 2
[Test Details]
Activate the water valve
ON or OFF
Unused
Activate the Water Flow Valve 3
[Test Details]
Activate the water valve
ON or OFF
Water valve intrusive valve operation (position when engine is in pre-heat mode)
(Click here)
Activate the Water Flow Valve 4
[Test Details]
Activate the water valve
ON or OFF
Water valve intrusive valve operation (position when hot coolant recovering)
(Click here)
Activate the Water Flow Valve 5
[Test Details]
Activate the water valve
ON or OFF
Water valve intrusive valve operation (position when engine is in normal operation)
(Click here)
Activate the Vacuum Pump
[Test Details]
Activate the leak detection pump
ON or OFF
-
Activate the VSV for Vent Valve
[Test Details]
Activate the vent valve
ON or OFF
-

SYSTEM CHECK

HINT:
Performing a System Check enables the system, which consists of multiple actuators, to be operated without removing any parts. In addition, it can show whether or not any DTCs are set, and can detect potential malfunctions in the system. The System Check can be performed with Techstream.

  1. Connect Techstream to the DLC3.

  2. Turn the power switch ON (READY).

  3. Turn the tester ON.

  4. Enter the following menus: Powertrain / Engine and ECT / Utility.

  5. Perform the System Check by referring to the below.


Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Evaporative System Check
(Automatic Mode)
Perform 9 steps in order to operate EVAP key-off monitor automatically
35°C (95°F) or less
  1. If no DTCs are in PENDING CODE after performing this test, system is functioning normally
Evaporative System Check
(Manual Mode)
Perform 9 steps in order to operate EVAP key-off monitor automatically
35°C (95°F) or less
  1. Used to detect malfunctioning parts