DTC P0171 System Too Lean (Fuel Trim) |
DTC P0172 System Too Rich (Bank 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0171 | When air-fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on LEAN side (2 trip detection logic) |
|
| P0172 | When air-fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on RICH side (2 trip detection logic) |
|

| Related DTCs | P0171: Fuel system lean (bank 1) P0172: Fuel system rich (bank 1) |
| Required sensors/components | Main: A/F sensor Related: Engine coolant temperature sensor, mass air flow meter, crankshaft position sensor |
| Frequency of operation | Continuous |
| Duration | Within 10 seconds |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | P0010 (VVT OCV) P0011 (VVT system 1 - Advance) P0012 (VVT system 1 - Retard) P0031, P0032 (A/F sensor heater - Sensor 1) P0100 - P0103 (MAF meter) P0115 - P0118 (ECT sensor) P0120 - P0223, P2135 (TP sensor) P0125 (Insufficient ECT for closed loop) P0335 (CKP sensor) P0340, P0341 (CMP sensor) P0351 - P0354 (Igniter) P0500 (VSS) |
| Fuel system status | Closed-loop |
| Battery voltage | 11 V or more |
| Either of the following conditions is met: | (a) or (b) |
| (a) Engine speed | Less than 1,100 rpm |
| (b) Intake air amount per revolution | 0.22 g/rev or more |
| EVAP purge-cut | Executing |
| Either of the following conditions is met | (a) or (b) |
| (a) Average between short-term fuel trim and long-term fuel trim | 33% or more (varies with ECT) |
| (b) Average between short-term fuel trim and long-term fuel trim | -30% or less (varies with ECT) |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() ![]() | ![]() ![]() | - |
| 2 | ![]() ![]() | ![]() ![]() |
|
| 3 | ![]() ![]() | ![]() ![]() |
|
| 4 | ![]() ![]() | ![]() ![]() |
|
| 1.CHECK AIR INDUCTION SYSTEM |
Check for vacuum leaks in the air induction system.
|
| ||||
| OK | |
| 2.CHECK CONNECTION OF PCV HOSE |
|
| ||||
| OK | |
| 3.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME) |
|
| ||||
| OK | |
| 4.INSPECT MASS AIR FLOW METER |
![]() |
Remove the mass air flow meter.
Inspect the output voltage.
Apply battery voltage across terminals +B and E2G.
Connect the positive (+) tester probe to terminal VG, and negative (-) tester probe to terminal E2G.
Blow air into the mass air flow meter, and check that the voltage fluctuates.
| Tester Connection | Specified Condition |
| 3 (VG) - 2 (E2G) | Sensor output voltage fluctuates between 0.3 V and 4.8 V |
Inspect the resistance.
Measure the resistance between the terminals of the mass air flow meter.
| Tester Connection | Specified Condition |
| 4 (THA) - 5 (E2) | 13.6 to 18.4 kΩ at -20°C (-4°F) |
| 4 (THA) - 5 (E2) | 2.21 to 2.69 kΩ at 20°C (68°F) |
| 4 (THA) - 5 (E2) | 0.49 to 0.67 kΩ at 60°C (140°F) |
Reinstall the mass air flow meter.
|
| ||||
| OK | |
| 5.INSPECT ENGINE COOLANT TEMPERATURE SENSOR (RESISTANCE) |
![]() |
Remove the engine coolant temperature sensor.
Measure the resistance between the terminals of the engine coolant temperature sensor.
| Tester Connection | Specified Condition |
| 1 - 2 | 2 to 3 kΩ at 20°C (68°F) |
| 1 - 2 | 0.2 to 0.4 kΩ at 80°C (176°F) |
Reinstall the engine coolant temperature sensor.
|
| ||||
| OK | |
| 6.CHECK SPARK AND IGNITION |
|
| ||||
| OK | |
| 7.CHECK FUEL PRESSURE |
|
| ||||
| OK | |
| 8.INSPECT FOR EXHAUST GAS LEAK |
|
| ||||
| OK | |
| 9.READ VALUE OF TECHSTREAM (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR [BANK 1 SENSOR 1]) |
Connect Techstream to the DLC 3.
Put the engine in inspection mode (Click here).
Warm up the A/F sensors (bank 1 sensor 1) by running the engine at 2,500 rpm with the accelerator pedal depressed more than 60 % for approximately 90 seconds.
Read the A/F sensor voltage output on Techstream.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Select "AFS B1 S1/Engine Speed" and press button "YES".
Monitor the A/F sensor voltage carefully.
Check the A/F sensor voltage output under the following conditions:
Put the engine in inspection mode and allow the engine to idle for 30 seconds.
Put the engine in inspection mode and run the engine at 2,500 rpm with the accelerator pedal depressed more than 60% (where engine RPM is not suddenly changed).
Deactivate the inspection mode and drive the vehicle with the shift position "B".
Accelerate the vehicle to 70 km/h (44 mph) and quickly release the accelerator pedal so that the throttle valve is fully closed.

|
| ||||
| NG | |
| 10.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the A5 A/F sensor connector.
Measure the resistance between the terminals of the A/F sensor.
| Tester Connection | Specified Condition |
| 1 (HT) - 2 (+B) | 1.8 to 3.4 Ω at 20°C (68°F) |
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 11.INSPECT INTEGRATION RELAY (EFI M RELAY) |
![]() |
Remove the integration relay from the engine room relay block.
Inspect the EFI M relay.
| Tester Connection | Specified Condition |
| 3K-1 - 3I-8 | 10 kΩ or higher |
| 3K-1 - 3I-8 | Below 1 Ω (Apply battery voltage to terminals 3I-6 and 3I-7) |
Reinstall the integration relay.
|
| ||||
| OK | |
| 12.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() ![]() |
Disconnect the A5 A/F sensor connector.
![]() |
Disconnect the E5 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| A5-3 (AF+) - E5-23 (A1A+) | Below 1 Ω |
| A5-4 (AF-) - E5-22 (A1A-) | Below 1 Ω |
| A5-1 (HT) - E5-7 (HA1A) | Below 1 Ω |
| Tester Connection | Specified Condition |
| A5-3 (AF+) or E5-23 (A1A+) - Body ground | 10 kΩ or higher |
| A5-4 (AF-) or E5-22 (A1A-) - Body ground | 10 kΩ or higher |
| A5-1 (HT) or E5-7 (HA1A) - Body ground | 10 kΩ or higher |
Reconnect the A/F sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 13.REPLACE AIR FUEL RATIO SENSOR |
| NEXT | |
| 14.PERFORM CONFIRMATION DRIVING PATTERN |

Clear the DTCs (Click here).
Connect Techstream to the DLC3.
Switch the ECM from normal mode to check mode using Techstream (Click here).
Put the engine in inspection mode, and start the engine and warm it up with all the accessory switches OFF.
Deactivate inspection mode and drive the vehicle at 70 to 120 km/h (44 to 75 mph) and engine speed of 1,100 to 3,200 rpm for 5 to 10 minutes.
| NEXT | |
| 15.READ OUTPUT DTCS (SEE IF DTC P0171 AND/OR P0172 ARE OUTPUT AGAIN) |
Connect Techstream to the DLC3.
Turn the power switch ON (IG).
Turn Techstream ON.
Enter the following menus: Powertrain / Engine and ECT / Trouble Code.
Read the DTCs using Techstream.
| Display (DTC Output) | Proceed to |
| No output | A |
| P0171 and/or P0172 | B |
|
| ||||
| A | |
| 16.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST |
|
| ||||
| YES | ||
| ||
| 17.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 18.READ OUTPUT DTCS (SEE IF DTC P0171 AND/OR P0172 ARE OUTPUT AGAIN) |
Connect Techstream to the DLC3.
Turn the power switch ON (IG).
Turn Techstream ON.
Enter the following menus: Powertrain / Engine and ECT / Trouble Code.
Read the DTCs using Techstream.
| Display (DTC Output) | Proceed to |
| No output | A |
| P0171 and/or P0172 | B |
|
| ||||
| A | |
| 19.REPLACE AIR FUEL RATIO SENSOR |
| NEXT | |
| 20.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 21.READ OUTPUT DTCS (SEE IF DTC P0171 AND/OR P0172 ARE OUTPUT AGAIN) |
Connect Techstream to the DLC3.
Turn the power switch ON (IG).
Turn Techstream ON.
Enter the following menus: Powertrain / Engine and ECT / Trouble Code.
Read the DTCs using Techstream.
| Display (DTC Output) | Proceed to |
| No output | A |
| P0171 and/or P0172 | B |
|
| ||||
| A | |
| 22.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST |
|
| ||||
| YES | ||
| ||