Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING UNIT

AIR CONDITIONING UNIT > REMOVAL

for Preparation Click here




1. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Turn the A/C switch on.

  1. Operate the A/C with the setting temperature at 25 °C (77°F) and the blower level at LO for 10 minutes to circulate the refrigerant, and collect compressor oil remaining in each component into the cooler compressor as much as possible.

  1. Stop the engine.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.



2. DISCONNECT SUCTION HOSE SUB-ASSEMBLY


    I003838E03
  1. Check SST installation direction.

    SST
    09870-00015  

    HINT:
    Set SST so that the stopper side is on the piping clamp lock side.

  1. Install SST on the piping clamp.



    I003839E01
  1. Push down on SST with your thumb while holding the pipe with both hands.

    NOTICE:
    Be careful not to bend the pipe.

  1. Pull SST until the stopper touches the pipe.

  1. Raise SST stopper and remove the piping clamp with SST from the pipe.

  1. Remove the piping clamp from SST.



    I006919E11
  1. Disconnect the suction hose by hand or using a screwdriver.

  1. Remove the 2 O-rings from the suction hose.

    NOTICE:
    1. Do not apply excessive force to the suction hose.
    2. Seal the opening of the disconnected part using vinyl tape to prevent moisture and foreign matter from entering it.



3. DISCONNECT COOLER REFRIGERANT LIQUID PIPE E (TO COOLER UNIT)
SST
09870-00025  

HINT:
Use the same procedures described for the suction hose.



4. DISCONNECT HEATER WATER HOSE B


    I038565E01
  1. Slide the clip and disconnect the heater water hose B.

    NOTICE:
    1. Do not apply excessive force to the water hose B.
    2. Prepare a drain pan or cloth for when the cooling water leaks.



5. DISCONNECT HEATER WATER HOSE A
  1. Slide the clip and disconnect the heater water hose A.

    NOTICE:
    1. Do not apply excessive force to the water hose A.
    2. Prepare a drain pan or cloth for when the cooling water leaks.



6. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY WITH PASSENGER AIRBAG ASSEMBLY

HINT:
Refer to the removal procedures for the instrument panel with the passenger airbag (Click here).



7. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY LOWER

HINT:
Refer to the removal procedures for the instrument panel lower (Click here).



8. REMOVE NO. 3 AIR DUCT REAR


    I038823E03
  1. Fold back the floor carpet.

    HINT:
    Fold back the floor carpet so that the No. 3 air duct rear can be removed.

  1. Detach the 10 claws and then remove the No. 3 air duct rear.



9. REMOVE NO. 3 HEATER TO REGISTER DUCT


    I038566E01
  1. Remove the clip and No. 3 heater to register duct with the No. 2 side defroster nozzle duct.



10. REMOVE NO. 1 HEATER TO REGISTER DUCT


    I038567E01
  1. Remove the No. 1 duct with the No. 1 side defroster nozzle duct.



11. REMOVE NO. 2 HEATER TO REGISTER DUCT


I038568E01


12. REMOVE DEFROSTER NOZZLE ASSEMBLY


    I038569E03
  1. Remove the 2 clips.

  1. Detach the 3 claws and then remove the defroster nozzle.



13. REMOVE TRANSMISSION CONTROL ECU ASSEMBLY


14. REMOVE ECM


15. REMOVE NETWORK GATEWAY ECU


16. REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY


    I039536E01
  1. Detach the clamp and disconnect the harness.

  1. Remove the 2 bolts, nut and instrument panel brace.



17. REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY
  1. Remove the air conditioning amplifier (Click here).



18. REMOVE STEERING COLUMN ASSEMBLY
  1. Remove the steering column (Click here).



19. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY


  1. Disconnect each connector and remove each clamp. Disconnect the wire harness.


    I038978E03



  1. Remove the 7 bolts, 2 nuts and then remove the instrument panel reinforcement with the air conditioner unit.


    I038973E01



20. REMOVE AIR CONDITIONING UNIT ASSEMBLY


    I038974E03
  1. Disconnect the 5 connectors.

  1. Detach the 9 clamps and disconnect the wire harness.



    I038975E03
  1. Remove the bolt.

  1. Detach the clamp and disconnect the junction connector.



    I038976E01
  1. Remove the 2 screws and air conditioning unit from the instrument panel reinforcement.