Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C0200/31    Front Speed Sensor RH Circuit

DTC    C0205/32    Front Speed Sensor LH Circuit

DTC    C1271/71    Low Output Signal of Front Speed Sensor RH (Test Mode DTC)

DTC    C1272/72    Low Output Signal of Front Speed Sensor LH (Test Mode DTC)

for Preparation Click here


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the ECU. These signals are used to control the ABS control system. The front and rear rotors have 48 serrations, respectively.
When the rotors rotate, the magnetic field emitted by the permanent magnet in the speed sensor generates an AC voltage. Since the frequency of this AC voltage changes in direct proportion to the speed of the rotor, the frequency is used by the ECU to detect the speed of each wheel.
DTCs C1271/71 and C1272/72 can be deleted when the speed sensor sends a vehicle speed signal or the Test Mode ends. DTCs C1271/71 and C1272/72 are output only in the Test Mode.
F000010E05

DTC No.
INF Code
DTC Detection Condition
Trouble Area
C0200/31
251
252
253
254
255
256
257
258
259
260
261
262
When one of following conditions is met:
  1. Speed of a malfunctioning wheel is 0 km/h (0 mph) for at least 15 sec. when vehicle speed is 10 km/h (6 mph) or more.
  2. Speed of the slowest wheel is less than 1/7th of the 2nd slowest wheel for at least 15 sec. when vehicle speed is 10 km/h (6 mph) or more.
  3. Abnormal high wheel speed pulse is input for at least 15 sec.
  4. Abnormal high wheel speed pulse is input at least 7 times when ECU is on.
  5. Speed sensor pulse signal is instantly cut 7 times or more.
  6. Speed sensor signal line is open for at least 0.5 sec.
  1. Right front and left front speed sensor
  2. Each speed sensor circuit
  3. Sensor rotor
  4. Sensor installation
C0205/32
264
265
266
267
268
269
270
271
272
273
274
275
When one of following conditions is met:
  1. Speed of a malfunctioning wheel is 0 km/h (0 mph) for at least 15 sec. when vehicle speed is 10 km/h (6 mph) or more.
  2. Speed of the slowest wheel is less than 1/7th of the 2nd slowest wheel for at least 15 sec. when vehicle speed is 10 km/h (6 mph) or more.
  3. Abnormal high wheel speed pulse is input for at least 15 sec.
  4. Abnormal high wheel speed pulse is input at least 7 times when ECU is on.
  5. Speed sensor pulse signal is instantly cut 7 times or more.
  6. Speed sensor signal line is open for at least 0.5 sec.
  1. Right front and left front speed sensor
  2. Each speed sensor circuit
  3. Sensor rotor
  4. Sensor installation
C1271/71
C1272/72
-
Detected only during Test Mode.
  1. Front speed sensor
  2. Front speed sensor circuit
  3. Sensor rotor
  4. Sensor installation

HINT:
  1. DTC C0200/31 is for the right front speed sensor.
  2. DTC C0205/32 is for the left front speed sensor.
  3. The BRAKE warning light comes on when speed sensor malfunctions are detected in 2 or more wheels.


WIRING DIAGRAM


C126244E04


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU, perform initialization of linear solenoid valve and calibration (Click here).

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using Techstream, check for any momentary interruption in the wire harness and connector corresponding to a DTC (Click here).

    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Speed Open
    FR speed sensor open detection / OPN-DET or NORMAL
    NORMAL: Normal condition
    -
    FL Speed Open
    FL speed sensor open detection / OPN-DET or NORMAL
    NORMAL: Normal condition
    -

    OK:
    There are no momentary interruptions.

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
Go to step 5
OK


2.READ VALUE OF TECHSTREAM (FRONT SPEED SENSOR)
  1. Check the Data List for proper functioning of the front speed sensor.

    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Wheel Speed
    Wheel speed sensor (FR) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    Similar speed as indicated on speedometer
    FL Wheel Speed
    Wheel speed sensor (FL) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    Similar speed as indicated on speedometer

    OK:
    There is almost no difference from the displayed speed value.

    HINT:
    There is tolerance of +-10% in the speedometer indication.



NG
Go to step 4
OK


3.CHECK SPEED SENSOR AND SENSOR ROTOR SERRATIONS


    F100551E08
  1. Connect the oscilloscope to terminal FR+ and FR-, or FL+ and FL- of the skid control ECU.

  1. Drive the vehicle at approximately 30 km/h (19 mph), and check the signal waveform.

    OK:
    A waveform as shown should be output.

    HINT:
    1. As the vehicle speed (wheel revolution speed) increases, a cycle of the waveform narrows and the fluctuation in the output voltage becomes greater.
    2. When noise is identified in the waveform on the oscilloscope, error signals are generated due to the speed sensor rotor's scratches, looseness or foreign matter deposited on it.



NG
Go to step 6
OK

REPLACE SKID CONTROL ECU 

4.INSPECT FRONT SPEED SENSOR


    C093876E19
  1. Disconnect the speed sensor connector.

  1. Measure the resistance of the sensors.

    Standard resistance:
    for LH:
    Tester Connection
    Specified Condition
    A3-2 (FL+) - A3-1 (FL-)
    1.4 to 1.8 kΩ
    A3-1 (FL-) - Body ground
    10 kΩ or higher
    A3-2 (FL+) - Body ground
    10 kΩ or higher
    for RH:
    Tester Connection
    Specified Condition
    A4-2 (FR+) - A4-1 (FR-)
    1.4 to 1.8 kΩ
    A4-1 (FR-) - Body ground
    10 kΩ or higher
    A4-2 (FR+) - Body ground
    10 kΩ or higher

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE FRONT SPEED SENSOR
OK


5.CHECK WIRE HARNESS (SKID CONTROL ECU - FRONT SPEED SENSOR)
C178033E01
  1. Disconnect the S7 and S10 ECU connectors.

  1. Disconnect the A3 and A4 sensor connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    for LH:
    Tester Connection
    Specified Condition
    A3-1 (FL-) - S10-22 (FL-)
    Below 1 Ω
    A3-2 (FL+) - S10-28 (FL+)
    Below 1 Ω
    A3-2 (FL+) - Body ground
    10 kΩ or higher
    A3-1 (FL-) - Body ground
    10 kΩ or higher
    for RH:
    Tester Connection
    Specified Condition
    A4-1 (FR-) - S7-22 (FR-)
    Below 1 Ω
    A4-2 (FR+) - S7-32 (FR+)
    Below 1 Ω
    A4-2 (FR+) - Body ground
    10 kΩ or higher
    A4-1 (FR-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6.CHECK SPEED SENSOR AND SENSOR ROTOR SERRATIONS


    F100551E09
  1. Connect the oscilloscope to terminals FR+ and FR-, or FL+ and FL- of the skid control ECU.

  1. Drive the vehicle at approximately 30 km/h (19 mph), and check the signal waveform.

    OK:
    A waveform as shown should be output.

    HINT:
    1. As the vehicle speed (wheel revolution speed) increases, a cycle of the waveform narrows and the fluctuation in the output voltage becomes greater.
    2. When noise is identified in the waveform on the oscilloscope, error signals are generated due to the speed sensor rotor's scratches, looseness or foreign matter deposited on it.



NG
Go to step 7
OK

REPLACE SKID CONTROL ECU 

7.INSPECT FRONT SPEED SENSOR INSTALLATION


    C108871E01
  1. Check the speed sensor installation.

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and front steering knuckle.

Torque:
8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

NOTICE:
Check the speed sensor signal after the replacement (Click here).



NG
REPLACE FRONT SPEED SENSOR
OK

REPLACE SKID CONTROL ECU