ELECTRONICALLY CONTROLLED BRAKE SYSTEM > TEST MODE PROCEDURE |
| CHECK WARNING LIGHT AND INDICATOR LIGHT |
![]() |
Release the parking brake pedal.
When the power switch is ON (READY), check that the ABS warning light, VSC warning light, BRAKE warning light, brake control warning light and SLIP indicator light come on for approximately 3 seconds.
| Trouble Area | See procedure |
| ABS warning light circuit |
Click here
|
| VSC warning light circuit |
Click here
|
| BRAKE warning light circuit |
Click here
|
| Brake control warning light circuit |
Click here
|
| SLIP indicator light circuit |
Click here
|
| CHECK SENSOR SIGNAL BY TEST MODE |
Step 1: Procedures for Test Mode
Turn the power switch OFF.
Connect Techstream to the DLC3.
Check that the steering wheel is in the centered position and move the shift lever to the P position.
Turn the power switch ON (READY).
![]() |
Select the Signal Check following the Techstream screen.
Check that the ABS warning light and VSC warning light indicates Test Mode.
| Trouble Area | See Procedure |
| ABS warning light circuit |
Click here
|
| VSC warning light circuit |
Click here
|
Start the engine.
Step 2: Check deceleration sensor
Check that the ABS warning light is blinking in Test Mode.
Keep the vehicle in the stationary condition on a level surface for 1 second or more.
![]() |
Step 3: Check yaw rate sensor
Shift the shift lever to the D range and drive the vehicle at the vehicle speed of approx. 5 km/h (3 mph), turn the steering wheel either to left or right 90° or more, and drive in a half-circle pattern.
Stop the vehicle and move the shift lever to the P position, check that the skid control buzzer sounds for 3 seconds.
![]() |
Step 4: Check master cylinder pressure sensor
Check that the ABS warning light is blinking in Test Mode.
Leave the vehicle in a stationary condition and the brake pedal in a free condition for 1 second or more, and quickly depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second or more.
While the vehicle is stopped, release the brake pedal.
While the vehicle is stopped, quickly depress the brake pedal once or more and check the ABS warning light is lit for 3 seconds.
![]() |
Step 5: Check speed sensor
Check the ABS warning light is blinking of Test Mode.
Start the sensor signal check.
Drive the vehicle straight forward. Drive the vehicle at a speed of 45 to 80 km/h (28 to 50 mph) or higher for several seconds and check that the ABS warning light goes off.
| Vehicle Speed | Test | Check |
| 0 to 45 km/h (0 to 28 mph) | Low speed test | Response of sensors |
| 45 to 80 km/h (28 to 50 mph) | Middle speed test | Deviations of sensor signal |
Step 6: Check end of sensor
If the sensor check is completed, the ABS warning light blinks (Test Mode) when the vehicle stops and the warning light is off when the vehicle is driving.
![]() |
Step 7: Read Test Mode
Using Techstream, check the DTCs in the Test Mode (refer to step 8).
Step 8: DTC of Test Mode
| Code No. | Diagnosis | Trouble Area |
| C1271/71 | Low output voltage of right front speed sensor |
|
| C1272/72 | Low output voltage of left front speed sensor |
|
| C1273/73 | Low output voltage of right rear speed sensor |
|
| C1274/74 | Low output voltage of left rear speed sensor |
|
| C1275/75 | Abnormal change in output voltage of right front speed sensor | Right front sensor rotor |
| C1276/76 | Abnormal change in output voltage of left front speed sensor | Left front speed sensor rotor |
| C1277/77 | Abnormal change in output voltage of right rear speed sensor | Right rear sensor rotor |
| C1278/78 | Abnormal change in output voltage of left rear speed sensor | Left rear speed sensor rotor |
| C1279/79 | Deceleration sensor is faulty |
|
| C1281/81 | Master cylinder pressure sensor output signal is faulty | Master cylinder pressure sensor |
| C0371/71 | Signal malfunction | Yaw rate sensor (Deceleration sensor) |