Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › 2011.12–2013.12
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0277909 SFI SYSTEM(w/o Canister Pump Module) J

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  ECM Power Source Circuit  


DESCRIPTION

When the power switch is turned on (IG), auxiliary battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil of the No. 1 integration relay (EFI MAIN relay), closing the contact and supplying power to terminals +B and +B2 of the ECM.

WIRING DIAGRAM

A275903E01
5.033,0.724 5.307,0.880 0.273,0.156 10 A39 1.581,1.889 1.681,2.027 0.100,0.137 10 2 2.634,3.711 3.272,3.876 0.637,0.165 10 EFI-MAIN 5.611,1.481 5.797,1.648 0.186,0.167 10 37 5.908,2.528 6.189,2.677 0.281,0.149 10 +B2 5.908,3.003 6.120,3.152 0.211,0.149 10 +B 5.908,3.427 6.335,3.576 0.427,0.149 10 MREL 5.908,1.555 6.314,1.704 0.406,0.149 10 IGSW 5.908,3.947 6.126,4.095 0.218,0.149 10 E1 6.24,4.37 6.597,4.517 0.357,0.147 10 ECM 2.834,2.361 3.110,2.526 0.276,0.165 10 IG2 0.804,1.815 1.072,1.980 0.268,0.165 10 P/I 0.568,4.388 1.204,4.737 0.636,0.350 10 Auxiliary Battery 5.033,0.884 7.129,1.058 2.096,0.174 10 Power Management Control ECU 5.56,1.658 5.833,1.814 0.273,0.156 10 A40 1.539,2.075 1.838,2.239 0.300,0.165 10 2D 1.591,1.476 1.691,1.614 0.100,0.137 10 1 2.157,4.179 3.608,4.344 1.451,0.165 10 No. 1 Integration Relay 1.914,3.14 2.561,3.305 0.647,0.165 10 EFI-MAIN 0.444,3.694 0.815,3.859 0.371,0.165 10 MAIN 1.595,3.231 1.696,3.368 0.100,0.137 10 2 1.543,3.418 1.843,3.582 0.300,0.165 10 2C 1.548,1.656 1.847,1.821 0.300,0.165 10 2E 3.444,1.151 3.544,1.289 0.100,0.137 10 3 3.472,1.355 3.772,1.519 0.300,0.165 10 2D 3.949,1.49 4.050,1.627 0.100,0.137 10 4 3.906,1.657 4.206,1.822 0.300,0.165 10 2D 3.933,2.811 4.123,2.949 0.189,0.137 10 4 3.887,2.991 4.187,3.156 0.300,0.165 10 2C 3.935,3.249 4.035,3.387 0.100,0.137 10 3 3.88,3.417 4.179,3.582 0.300,0.165 10 2C 5.867,0.362 6.273,0.511 0.406,0.149 10 IG2D 5.644,2.356 5.830,2.523 0.186,0.167 10 3 5.556,2.533 5.830,2.689 0.273,0.156 10 A40 5.648,2.82 5.834,2.987 0.186,0.167 10 2 5.561,2.985 5.834,3.141 0.273,0.156 10 A40 5.604,3.236 5.790,3.403 0.186,0.167 10 46 5.552,3.413 5.826,3.569 0.273,0.156 10 A40 5.604,3.779 5.790,3.947 0.186,0.167 10 16 5.558,3.953 5.831,4.109 0.273,0.156 10 C10 4.576,1.804 5.204,2.110 0.628,0.306 10 IG2 NO.2 5.698,0.268 5.884,0.435 0.186,0.167 10 2 2.114,1.785 2.391,1.950 0.276,0.165 10 IG2 5.615,4.13 5.825,4.286 0.211,0.156 10 *1 5.283,3.779 5.469,3.947 0.186,0.167 10 16 5.261,3.945 5.535,4.101 0.273,0.156 10 C9 5.294,4.13 5.505,4.286 0.211,0.156 10 *2 1.456,5.139 2.366,5.302 0.909,0.163 10 *1: for LHD 1.456,5.402 2.366,5.565 0.909,0.163 10 *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C10-16 (E1) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
C9-16 (E1) - Body ground Always Below 1 Ω




OK

2.CHECK TERMINAL VOLTAGE (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (IGSW VOLTAGE)
a.
U158929E03
1.854,1.375 1.708,1.927 false 0.708,0.115 0.875,0.292 0.167,0.177 10 false *a 0.604,1.104 0.865,1.281 0.26,0.177 10 false A40 1.521,1.938 2.021,2.146 0.5,0.208 10 false IGSW

Disconnect the ECM connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-37 (IGSW) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

3.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN RELAY)

NG

6.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY)
3.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN RELAY)
a.

Inspect the No. 1 integration relay (EFI MAIN relay) (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>INTEGRATION RELAY>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

NG

REPLACE NO. 1 INTEGRATION RELAY (EFI MAIN RELAY)

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay and ENG W/PMP relay from the No. 2 engine room relay block and No. 2 junction block assembly.

HINT:

Remove the ENG W/PMP relay connected between the checked terminals as the coil inside the relay influences the measurement value.



b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-4 - A40-2 (+B) Always Below 1 Ω
2C-4 - A40-3 (+B2) Always Below 1 Ω
2C-3 - A40-46 (MREL) Always Below 1 Ω
2C-4 or A40-2 (+B) - Body ground Always 10 kΩ or higher
2C-4 or A40-3 (+B2) - Body ground Always 10 kΩ or higher
2C-3 or A40-46 (MREL) - Body ground Always 10 kΩ or higher




OK

5.CHECK TERMINAL VOLTAGE (NO. 1 INTEGRATION RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (NO. 1 INTEGRATION RELAY - BODY GROUND)
a.

Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-2 - Body ground Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY)
a.

Inspect the No. 1 integration relay (IG2 relay) (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>INTEGRATION RELAY>INSPECTION).



OK

7.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

NG

REPLACE NO. 1 INTEGRATION RELAY (IG2 RELAY)

7.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-4 - A40-37 (IGSW) Always Below 1 Ω
2D-4 or A40-37 (IGSW) - Body ground Always 10 kΩ or higher




OK

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)
a.
U158980E04
0.823,1.313 1.146,1.479 0.323,0.167 10 false 2E 0.167,0.083 0.406,0.229 0.24,0.146 10 false *a

Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2E-1 - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to No. 1 Integration Relay)



OK

9.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - NO. 1 INTEGRATION RELAY)

9.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)
a.

Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-2 - Body ground Always Below 1 Ω




OK

10.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)
a.

Disconnect the power management control ECU connector.


b.

Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-2 (IG2D) - 2D-3 Always Below 1 Ω
A39-2 (IG2D) or 2D-3 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR