Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › 2014.12–2015.11
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0277909 SFI SYSTEM C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P0351 is output, check the No. 1 ignition coil assembly circuit.

·

If DTC P0352 is output, check the No. 2 ignition coil assembly circuit.

·

If DTC P0353 is output, check the No. 3 ignition coil assembly circuit.

·

If DTC P0354 is output, check the No. 4 ignition coil assembly circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil assembly and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The spark of the spark plugs passes from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current supplied to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A255924E23
4.427,1.396 4.375,0.948 4.375,0.948 4.302,0.948 false 5.396,1.146 5.656,0.802 5.656,0.802 5.781,0.802 false 3.854,0.865 4.458,1.167 0.604,0.302 10 false Igniter 4.24,0.354 5.698,0.531 1.458,0.177 10 false from Auxiliary Battery 5.823,0.729 6.938,1.167 1.115,0.438 10 false No. 1 Ignition Coil Assembly 5.615,1.854 6.729,2.031 1.115,0.177 10 false No. 1 Spark Plug 5.615,3.073 6.729,3.25 1.115,0.177 10 false No. 2 Spark Plug 5.615,4.396 6.729,4.573 1.115,0.177 10 false No. 3 Spark Plug 5.615,5.698 6.729,5.875 1.115,0.177 10 false No. 4 Spark Plug 2.74,5.958 3.083,6.135 0.344,0.177 10 false ECM 2.875,1.438 3.24,1.594 0.365,0.156 10 false IGT1 2.875,1.75 3.25,1.896 0.375,0.146 10 false IGF1 0.302,1.344 2.031,1.51 1.729,0.167 10 false Crank Position Sensor 0.313,3.146 2.042,3.313 1.729,0.167 10 false Cam Position Sensor 2.865,2.75 3.229,2.906 0.365,0.156 10 false IGT2 2.875,5.406 3.24,5.563 0.365,0.156 10 false IGT4 2.865,4.104 3.229,4.26 0.365,0.156 10 false IGT3 0.188,4.365 2.125,5.198 1.938,0.833 10 false Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter Sub-assembly, Throttle Position Sensor, etc.) 3.875,3.354 5.646,3.583 1.771,0.229 10 false No. 2 Ignition Coil Assembly 3.875,5.979 5.667,6.208 1.792,0.229 10 false No. 4 Ignition Coil Assembly 3.875,4.667 5.802,4.896 1.927,0.229 10 false No. 3 Ignition Coil Assembly

DTC No. DTC Detection Condition Trouble Area
P0351
P0352
P0353
P0354
No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT circuit (1 to 4) between ignition coil assembly and ECM

·

No. 1 to No. 4 ignition coil assemblies

·

ECM



A122717E50
3.042,0.958 3.406,1.156 0.365,0.198 10 false GND 3.031,1.594 3.365,1.792 0.333,0.198 10 false GND 0.208,0.802 0.583,1.01 0.375,0.208 10 false CH1 0.188,1.302 0.604,1.521 0.417,0.219 10 false CH2 0.052,0.031 0.594,0.208 0.542,0.177 10 false 2 V/DIV. 1.292,1.906 2.042,2.052 0.75,0.146 10 false 20 ms./DIV.

Reference: Inspection using an oscilloscope.


HINT:
·

The correct waveform is as shown.


·

While idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.



ECM Terminal Name CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling

MONITOR DESCRIPTION

A212405E10
1.782,1.645 2.181,1.818 0.399,0.173 10 ECM 2.956,1.3 3.225,1.485 0.269,0.185 10 IGT 2.949,1.726 3.226,1.886 0.278,0.160 10 IGF 4.153,1.509 4.594,1.655 0.441,0.145 10 Igniter 5.4,1.348 6.167,1.521 0.767,0.173 10 Ignition Coil 4.395,2.35 6.076,2.540 1.682,0.191 10 Ignition Coil Assembly 0.213,3.113 1.146,3.443 0.934,0.330 10 Ignition Signal (IGT) 1.642,3.541 2.131,3.731 0.489,0.191 10 Normal 1.383,3.947 2.150,4.138 0.767,0.191 10 Malfunction 0.185,3.891 1.153,4.408 0.968,0.517 10 Ignition Confirmation Signal (IGF1) 3.631,4.507 4.482,4.684 0.850,0.177 10 Circuit Open 5.95,4.97 6.314,5.167 0.364,0.198 10 Time

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Igniter
Required Sensors/Components (Related) Crank position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the power switch on (IG) and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the tester on.

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine.

8.

Idle the engine for 10 seconds or more.

9.

Enter the following menus: Powertrain / Engine and ECT / DTC.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0351, P0352, P0353 or P0354.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A275603E10
6.115,0.865 6.406,1.031 0.292,0.167 10 false IGN 0.677,2.729 1.333,3.063 0.656,0.333 10 false Auxiliary Battery 3.094,0.875 3.354,1.104 0.26,0.229 10 false IG2 2.469,1.021 2.635,1.208 0.167,0.188 10 false 2 4.875,0.573 5.042,0.76 0.167,0.188 10 false 4 2.458,0.573 2.625,0.76 0.167,0.188 10 false 1 4.875,1.021 5.042,1.208 0.167,0.188 10 false 3 1.635,0.896 1.938,1.125 0.302,0.229 10 false P/I 4.813,2.563 5.167,2.708 0.354,0.146 10 false IG2D 5.24,2.469 5.438,2.656 0.198,0.188 10 false 9 6.854,0.729 7.052,0.917 0.198,0.188 10 false A 4.052,3 4.375,3.146 0.323,0.146 10 false G77 4.052,3.156 5.656,3.583 1.604,0.427 10 false Certification ECU (Smart Key ECU Assembly) 2.906,1.823 4.396,2.052 1.49,0.229 10 false No. 1 Integration Relay 2.427,0.76 2.646,0.938 0.219,0.177 10 false 2E 4.833,0.76 5.052,0.938 0.219,0.177 10 false 2D 4.833,1.219 5.052,1.396 0.219,0.177 10 false 2D 2.427,1.208 2.646,1.385 0.219,0.177 10 false 2D 0.583,1.802 0.958,1.958 0.375,0.156 10 false MAIN 4.125,1.531 4.385,1.76 0.26,0.229 10 false IG2

A255703E09
5.653,0.791 6.012,0.947 0.360,0.156 10 IGT1 5.653,2.183 6.012,2.339 0.360,0.156 10 IGT2 5.653,3.559 6.012,3.715 0.360,0.156 10 IGT3 5.653,4.966 6.012,5.122 0.360,0.156 10 IGT4 5.653,5.73 6.012,5.886 0.360,0.156 10 IGF1 5.896,6.372 6.273,6.538 0.376,0.167 10 ECM 5.385,0.567 5.670,0.741 0.286,0.174 10 57 5.385,1.949 5.670,2.124 0.286,0.174 10 56 5.385,3.332 5.670,3.506 0.286,0.174 10 55 5.385,4.726 5.670,4.900 0.286,0.174 10 54 5.322,5.511 5.626,5.685 0.304,0.174 10 102 3.259,0.569 3.387,0.734 0.128,0.165 10 1 3.259,0.916 3.387,1.081 0.128,0.165 10 4 4.463,0.569 4.591,0.734 0.128,0.165 10 3 4.463,0.916 4.591,1.081 0.128,0.165 10 2 3.474,0.672 3.694,0.828 0.221,0.156 10 +B 4.055,0.672 4.391,0.842 0.336,0.170 10 IGT1 3.467,1.005 3.827,1.161 0.360,0.156 10 GND 4.108,1.005 4.384,1.171 0.276,0.165 10 IGF 2.832,1.41 3.100,1.566 0.268,0.156 10 C5 3.089,1.41 5.088,1.584 1.998,0.174 10 No. 1 Ignition Coil Assembly 3.259,1.97 3.387,2.135 0.128,0.165 10 1 3.259,2.317 3.387,2.482 0.128,0.165 10 4 4.463,1.97 4.591,2.135 0.128,0.165 10 3 4.463,2.317 4.591,2.482 0.128,0.165 10 2 3.474,2.073 3.694,2.229 0.221,0.156 10 +B 4.055,2.073 4.391,2.243 0.336,0.170 10 IGT2 3.467,2.407 3.827,2.562 0.360,0.156 10 GND 4.108,2.407 4.384,2.572 0.276,0.165 10 IGF 2.832,2.811 3.103,2.967 0.272,0.156 10 C6 3.089,2.811 5.097,2.985 2.008,0.174 10 No. 2 Ignition Coil Assembly 3.259,3.355 3.387,3.520 0.128,0.165 10 1 3.259,3.702 3.387,3.867 0.128,0.165 10 4 4.463,3.355 4.591,3.520 0.128,0.165 10 3 4.463,3.702 4.591,3.867 0.128,0.165 10 2 3.474,3.458 3.694,3.614 0.221,0.156 10 +B 4.055,3.458 4.391,3.628 0.336,0.170 10 IGT3 3.467,3.792 3.827,3.947 0.360,0.156 10 GND 4.108,3.792 4.384,3.957 0.276,0.165 10 IGF 2.832,4.196 3.117,4.352 0.286,0.156 10 C7 3.089,4.196 4.977,4.370 1.887,0.174 10 No. 3 Ignition Coil Assembly 3.259,4.744 3.387,4.910 0.128,0.165 10 1 3.259,5.091 3.387,5.256 0.128,0.165 10 4 4.463,4.744 4.591,4.910 0.128,0.165 10 3 4.463,5.091 4.591,5.256 0.128,0.165 10 2 3.474,4.847 3.694,5.003 0.221,0.156 10 +B 4.055,4.847 4.391,5.017 0.336,0.170 10 IGT4 3.467,5.181 3.827,5.337 0.360,0.156 10 GND 4.108,5.181 4.384,5.346 0.276,0.165 10 IGF 2.832,5.585 3.113,5.741 0.282,0.156 10 C8 3.089,5.585 4.912,5.759 1.823,0.174 10 No. 4 Ignition Coil Assembly 0.848,0.674 0.976,0.848 0.128,0.174 10 A 0.296,6.048 1.205,6.211 0.909,0.163 10 *1: for LHD 0.296,6.311 1.205,6.473 0.909,0.163 10 *2: for RHD 5.896,6.209 6.806,6.372 0.909,0.163 10 C10*1, C9*2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
a.

Disconnect the ignition coil assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C5-4 (GND) - Body ground Always Below 1 Ω
C6-4 (GND) - Body ground Always Below 1 Ω
C7-4 (GND) - Body ground Always Below 1 Ω
C8-4 (GND) - Body ground Always Below 1 Ω




OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
a.
U158833E04
1.313,2.479 0.781,3.01 true 2.156,2.49 2.615,3.01 true 0.323,0.198 0.51,0.406 0.188,0.208 10 false *a 0.656,3.031 0.865,3.208 0.208,0.177 10 false +B 2.594,3.031 2.958,3.188 0.365,0.156 10 false GND 0.177,1.979 0.448,2.125 0.271,0.146 10 false C5 0.646,1.969 0.948,2.177 0.302,0.208 10 false C7 0.177,2.25 0.531,2.438 0.354,0.188 10 false C6 0.656,2.25 0.948,2.417 0.292,0.167 10 false C8

Disconnect the ignition coil assembly connectors.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C5-1 (+B) - C5-4 (GND) Power switch on (IG) 11 to 14 V
C6-1 (+B) - C6-4 (GND) Power switch on (IG) 11 to 14 V
C7-1 (+B) - C7-4 (GND) Power switch on (IG) 11 to 14 V
C8-1 (+B) - C8-4 (GND) Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Ignition Coil Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C5-2 (IGF) - C10-102 (IGF1) Always Below 1 Ω
C6-2 (IGF) - C10-102 (IGF1) Always Below 1 Ω
C7-2 (IGF) - C10-102 (IGF1) Always Below 1 Ω
C8-2 (IGF) - C10-102 (IGF1) Always Below 1 Ω
C5-3 (IGT1) - C10-57 (IGT1) Always Below 1 Ω
C6-3 (IGT2) - C10-56 (IGT2) Always Below 1 Ω
C7-3 (IGT3) - C10-55 (IGT3) Always Below 1 Ω
C8-3 (IGT4) - C10-54 (IGT4) Always Below 1 Ω
C5-3 (IGT1) or C10-57 (IGT1) - Body ground Always 10 kΩ or higher
C6-3 (IGT2) or C10-56 (IGT2) - Body ground Always 10 kΩ or higher
C7-3 (IGT3) or C10-55 (IGT3) - Body ground Always 10 kΩ or higher
C8-3 (IGT4) or C10-54 (IGT4) - Body ground Always 10 kΩ or higher
C5-2 (IGF), C6-2 (IGF), C7-2 (IGF), C8-2 (IGF) or C10-102 (IGF1) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C5-2 (IGF) - C9-102 (IGF1) Always Below 1 Ω
C6-2 (IGF) - C9-102 (IGF1) Always Below 1 Ω
C7-2 (IGF) - C9-102 (IGF1) Always Below 1 Ω
C8-2 (IGF) - C9-102 (IGF1) Always Below 1 Ω
C5-3 (IGT1) - C9-57 (IGT1) Always Below 1 Ω
C6-3 (IGT2) - C9-56 (IGT2) Always Below 1 Ω
C7-3 (IGT3) - C9-55 (IGT3) Always Below 1 Ω
C8-3 (IGT4) - C9-54 (IGT4) Always Below 1 Ω
C5-3 (IGT1) or C9-57 (IGT1) - Body ground Always 10 kΩ or higher
C6-3 (IGT2) or C9-56 (IGT2) - Body ground Always 10 kΩ or higher
C7-3 (IGT3) or C9-55 (IGT3) - Body ground Always 10 kΩ or higher
C8-3 (IGT4) or C9-54 (IGT4) - Body ground Always 10 kΩ or higher
C5-2 (IGF), C6-2 (IGF), C7-2 (IGF), C8-2 (IGF) or C9-102 (IGF1) - Body ground Always 10 kΩ or higher




OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.



e.

Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 4 cylinders).

NOTICE:

Do not change the location of the connectors.



f.

Perform a simulation test.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.


h.

Read the DTCs.

Result
Result Proceed to
Same DTC output A
Different ignition coil DTC output B

HINT:

Perform "Inspection After Repair" after replacing the ignition coil assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).




A

B

5.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - NO. 1 INTEGRATION RELAY)
a.

Disconnect the ignition coil assembly connectors.


b.

Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C5-1 (+B) - 2D-4 Always Below 1 Ω
C6-1 (+B) - 2D-4 Always Below 1 Ω
C7-1 (+B) - 2D-4 Always Below 1 Ω
C8-1 (+B) - 2D-4 Always Below 1 Ω
C5-1 (+B), C6-1 (+B), C7-1 (+B), C8-1 (+B) or 2D-4 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR