Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module)
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0277909 SFI SYSTEM(w/o Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P0010  Camshaft Position "A" Actuator Circuit (Bank 1)  


DESCRIPTION

The Variable Valve Timing (VVT) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing.

The camshaft timing oil control valve assembly is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A384173E11
2.542,4.625 2.813,4.271 2.813,4.271 3.521,4.271 false 3.74,5.115 3.344,5.115 3.344,5.115 3.156,4.813 false 0.135,0.104 1.188,0.49 1.052,0.385 10 false VVT System: 0.177,2.646 0.979,3.021 0.802,0.375 10 false Duty-cycle 1.604,3.74 4.427,4.094 2.823,0.354 10 false Camshaft Timing Oil Control Valve Assembly 0.323,4.313 1.719,4.698 1.396,0.385 10 false Engine Oil Pressure 3.573,4.198 6.635,4.51 3.063,0.313 10 false VVT Controller (Camshaft Timing Gear Assembly) 3.802,5.01 5.344,5.385 1.542,0.375 10 false Intake Camshaft 4.896,0.854 6.854,1.177 1.958,0.323 10 false Cam Position Sensor 4.844,1.385 6.729,1.708 1.885,0.323 10 false Crank Position Sensor 4.51,1.885 6.823,2.198 2.313,0.313 10 false Mass Air Flow Meter Sub-assembly 4.823,2.385 6.563,2.771 1.74,0.385 10 false Throttle Position Sensor 4.49,2.885 6.802,3.156 2.313,0.271 10 false Engine Coolant Temperature Sensor 4.885,3.385 6.51,3.75 1.625,0.365 10 false Vehicle Speed Sensor 2.365,1.271 3.656,1.656 1.292,0.385 10 false Actual Valve Timing 2.354,2.021 3.74,2.396 1.385,0.375 10 false Target Valve Timing 2.646,2.729 3.448,3.104 0.802,0.375 10 false Correction 2.865,3.24 3.667,3.615 0.802,0.375 10 false ECM

DTC No. DTC Detection Condition Trouble Area
P0010 Open or short in camshaft timing oil control valve assembly circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve assembly circuit

·

Camshaft timing oil control valve assembly

·

ECM



MONITOR DESCRIPTION

This DTC is designed to detect an open or short in the camshaft timing oil control valve assembly circuit. If the camshaft timing oil control valve duty-cycle is excessively high or low while the power switch is on (IG) or the engine is running, the ECM will illuminate the MIL and store the DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the power switch on (IG) and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the tester on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / DTC.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0010.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A255118E21
0.557,1.862 2.341,2.232 1.785,0.370 10 Camshaft Timing Oil Control Valve Assembly 0.24,1.862 0.535,2.008 0.295,0.145 10 C20 1.591,0.804 1.698,0.950 0.107,0.145 10 1 1.591,1.44 1.698,1.585 0.107,0.145 10 2 4.864,0.8 5.072,0.945 0.207,0.145 10 75 4.863,1.442 5.065,1.587 0.202,0.145 10 74 5.136,1.444 5.543,1.589 0.407,0.145 10 OC1- 5.136,0.808 5.543,0.953 0.407,0.145 10 OC1+ 5.97,2.224 6.301,2.370 0.331,0.145 10 ECM 5.101,2.224 5.914,2.370 0.813,0.145 10 C10*1, C9*2 2.945,2.202 3.740,2.347 0.795,0.145 10 *1: for LHD 2.945,2.475 3.740,2.620 0.795,0.145 10 *2: for RHD

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (DTC P0010)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Clear the DTC after recording the freeze frame data and DTC.


e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the tester on.


h.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


i.

Start the engine and allow the engine to idle.


j.

Enter the following menus: Powertrain / Engine and ECT / DTC.


k.

Read the DTCs.

Result
Result Proceed to
DTC P0010 is output A
DTC is not output B



A

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

B

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the camshaft timing oil control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C20-1 - C10-75 (OC1+) Always Below 1 Ω
C20-2 - C10-74 (OC1-) Always Below 1 Ω
C20-1 or C10-75 (OC1+) - Body ground Always 10 kΩ or higher
C20-2 or C10-74 (OC1-) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C20-1 - C9-75 (OC1+) Always Below 1 Ω
C20-2 - C9-74 (OC1-) Always Below 1 Ω
C20-1 or C9-75 (OC1+) - Body ground Always 10 kΩ or higher
C20-2 or C9-74 (OC1-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR