The fuel injectors are located on the intake port. They inject fuel into the cylinders based on the signals from the ECM.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Disconnect the fuel injector assembly connectors.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C1-1 - Body ground | Power switch on (IG) | 11 to 14 V |
| C2-1 - Body ground | Power switch on (IG) | 11 to 14 V |
| C3-1 - Body ground | Power switch on (IG) | 11 to 14 V |
| C4-1 - Body ground | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector
(to Fuel Injector Assembly) |
OK
NG
Check the fuel injector assembly (See page Engine / Hybrid System>1NZ-FXE FUEL>FUEL INJECTOR>INSPECTION).
Perform "Inspection After Repair" after replacing the fuel injector assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).
OK
NG
Disconnect the fuel injector assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C1-1 - C10-20 (#10) | Always | Below 1 Ω |
| C2-1 - C10-17 (#20) | Always | Below 1 Ω |
| C3-1 - C10-18 (#30) | Always | Below 1 Ω |
| C4-1 - C10-19 (#40) | Always | Below 1 Ω |
| C1-1 or C10-20 (#10) - Body ground | Always | 10 kΩ or higher |
| C2-1 or C10-17 (#20) - Body ground | Always | 10 kΩ or higher |
| C3-1 or C10-18 (#30) - Body ground | Always | 10 kΩ or higher |
| C4-1 or C10-19 (#40) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C1-1 - C9-20 (#10) | Always | Below 1 Ω |
| C2-1 - C9-17 (#20) | Always | Below 1 Ω |
| C3-1 - C9-18 (#30) | Always | Below 1 Ω |
| C4-1 - C9-19 (#40) | Always | Below 1 Ω |
| C1-1 or C9-20 (#10) - Body ground | Always | 10 kΩ or higher |
| C2-1 or C9-17 (#20) - Body ground | Always | 10 kΩ or higher |
| C3-1 or C9-18 (#30) - Body ground | Always | 10 kΩ or higher |
| C4-1 or C9-19 (#40) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the fuel injector assembly connectors.
Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C1-2 - 2D-4 | Always | Below 1 Ω |
| C2-2 - 2D-4 | Always | Below 1 Ω |
| C3-2 - 2D-4 | Always | Below 1 Ω |
| C4-2 - 2D-4 | Always | Below 1 Ω |
| C1-2 or 2D-4 - Body ground | Always | 10 kΩ or higher |
| C2-2 or 2D-4 - Body ground | Always | 10 kΩ or higher |
| C3-2 or 2D-4 - Body ground | Always | 10 kΩ or higher |
| C4-2 or 2D-4 - Body ground | Always | 10 kΩ or higher |
OK
NG