Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0AA1-231  Hybrid Battery Positive Contactor Circuit Stuck Closed  


DESCRIPTION

Refer to the description for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

DTC No. INF Code DTC Detection Condition Trouble Area
P0AA1 231 SMRB on the HV battery positive side is stuck closed.
·

Hybrid battery junction block assembly

·

Inverter with converter assembly

·

Hybrid vehicle control ECU

·

Wire harness and connector



WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

CAUTION / NOTICE / HINT

CAUTION:
·

When performing P0AA1-231 troubleshooting, use either a tool wrapped with vinyl insulation tape or a insulated tool. (It is extremely dangerous when a high-voltage charge passes through a non-insulated tool causing a short.)

·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

If the DTCs are cleared or the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal before performing repairs, turning the power switch on (READY) may cause a malfunction. Do not turn the power switch on (READY).



HINT:
·

If P0AA1-231 is stored, the hybrid system cannot be turned on (READY).

·

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

(a)

Turn the power switch off and wait for 30 seconds or more.

(b)

Turn the power switch on (READY) and wait for 30 seconds or more.

(c)

Turn the power switch off and wait for 30 seconds or more.




PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
Only P0AA1-231 is output or P0AA1-231 and DTCs other than the ones in the table below are also output. A
Any of the following DTCs are also output. B


DTC No. Relevant Diagnosis
P06B0-163 Sensor Power Supply "A" Circuit/Open
P06D6-511 Sensor Reference Voltage "F" Circuit/Open
P06E6-164 Sensor Power Supply "C" Circuit/Open
P0A1A-151, 658, 791 Generator Control Module
P0A1B-786, 794 Drive Motor "A" Control Module
P0A1D-148 Hybrid Powertrain Control Module
P0A3F-243 Drive Motor "A" Position Sensor Circuit
P0A40-500 Drive Motor "A" Position Sensor Circuit Range/Performance
P0A41-245 Drive Motor "A" Position Sensor Circuit Low
P0A4B-253 Generator Position Sensor Circuit
P0A4C-513 Generator Position Sensor Circuit Range/Performance
P0A4D-255 Generator Position Sensor Circuit Low
P0ADC-226 Hybrid Battery Positive Contactor Control Circuit High
P0C76-523 Hybrid Battery System Discharge Time Too Long
P0CA3-442 DC/DC Converter Step Up Voltage Performance
P0D2E-586 Drive Motor "A" Inverter Voltage Sensor Circuit Range/Performance
P0D2F-266 Drive Motor "A" Inverter Voltage Sensor Circuit Low
P0D30-267 Drive Motor "A" Inverter Performance
P1C2A-155 Generator A/D Converter Circuit
P1C73-512 Sensor Standard Voltage "F" Circuit/Open
P1CA6-156 Generator Control Module Malfunction
P1CA7-193 Drive Motor Control Module Malfunction
P1CAC-200 Generator Position Sensor Angle Malfunction
P1CAD-168 Drive Motor "A" Position Sensor Angle Malfunction
P1CAF-792 Generator Position Sensor REF Signal Cycle Malfunction
P1CB0-795 Drive Motor "A" Position Sensor REF Signal Cycle Malfunction
P1CB2-793 Generator Position Sensor REF Signal Stop Malfunction
P1CB3-796 Drive Motor "A" Position Sensor REF Signal Stop Malfunction
P2511-149 HV CPU Power Relay Sense Circuit Intermittent No Continuity
P3004-132 High Voltage Power Resource
P3133-659 Communication Error from Generator to Drive Motor "A"
P3134-661 Communication Error from Drive Motor "A" to Generator
P324E-788 MG-ECU Power Relay Intermittent Circuit
U0110 (all INF codes)*1 Lost Communication with Drive Motor Control Module "A"

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P0AA1-231 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.




e.

Turn the power switch off.



A

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Read the freeze frame data of DTC P0AA1-231.

Result:
Result Proceed to
"VL-Voltage before Boosting" is 55 V or more. A
"VL-Voltage before Boosting" is less than 55 V. B


HINT:

If VH-Voltage after Boosting is output even when an off command is being sent to the system main relay (positive side), P0AA1-231 is output. If the difference between the "VL-Voltage before Boosting" and the "VH-Voltage after Boosting" is large, it is determined that there is an inverter (VH sensor) malfunction.



e.

Turn the power switch off.



A

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

B

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

5.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

NG

4.CONNECT SECURELY
4.CONNECT SECURELY

NEXT

5.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)
5.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)
a.

Check the connection condition of the MG5 floor wire connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

OK:
·

The connector is connected securely.

·

The terminals are not deformed and are connected securely.

·

No water or foreign matter in the connector.


Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C




A

8.CHECK CONNECTOR CONNECTION CONDITION (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

B

6.CONNECT SECURELY

C

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CONNECT SECURELY

NEXT

8.CHECK CONNECTOR CONNECTION CONDITION (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)
7.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

8.CHECK CONNECTOR CONNECTION CONDITION (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)
8.CHECK CONNECTOR CONNECTION CONDITION (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid vehicle battery cover panel LH (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.
A266763

Check the connector connections and contact pressure of the relevant terminals for the hybrid battery junction block assembly connector (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE ).

OK:

The connector is connected securely and there are no contact pressure problems.



d.

Install the No. 1 hybrid vehicle battery cover panel LH.



OK

10.CHECK GROUND WIRE CONNECTION CONDITION (SMR ACTIVATION LOW-VOLTAGE CIRCUIT)

NG

9.CONNECT SECURELY
9.CONNECT SECURELY

NEXT

10.CHECK GROUND WIRE CONNECTION CONDITION (SMR ACTIVATION LOW-VOLTAGE CIRCUIT)
10.CHECK GROUND WIRE CONNECTION CONDITION (SMR ACTIVATION LOW-VOLTAGE CIRCUIT)
a.

Check the installation condition of the G6 ground wire.

OK:

The G6 ground wire is securely installed.




OK

12.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HYBRIDBATTERY JUNCTION BLOCK ASSEMBLY)

NG

11.CONNECT SECURELY
11.CONNECT SECURELY

NEXT

12.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HYBRIDBATTERY JUNCTION BLOCK ASSEMBLY)
12.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HYBRIDBATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid vehicle battery cover panel LH (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.

Disconnect connector M40 from the hybrid battery junction block assembly.


d.

Disconnect connector G80 from the hybrid vehicle control ECU.


e.
A380673E09
1.833,2.417 2.25,2.667 0.417,0.25 1.458,3.583 1.875,3.833 0.417,0.25 1.479,1.792 2.031,1.792 false 2.615,4.438 2.208,3.771 false 0.094,0.135 0.406,0.333 0.313,0.198 10 false *a 0.135,2.656 0.448,2.854 0.313,0.198 10 false *b 1.021,1.719 1.563,2.083 0.542,0.365 10 false SMRB 1.906,2.458 2.219,2.656 0.313,0.198 10 false G80 1.531,3.625 1.844,3.823 0.313,0.198 10 false M40 2.656,4.385 3.208,4.667 0.552,0.281 10 false SMRB

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
G80-4 (SMRB) - M40-1 (SMRB) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
G80-4 (SMRB) and M40-1 (SMRB) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Rear view of wire harness connector
(to Hybrid Battery Junction Block Assembly)


f.

Connect the hybrid vehicle control ECU connector.


g.

Connect the hybrid battery junction block assembly connector.


h.

Install the No. 1 hybrid vehicle battery cover panel LH.



OK

14.CHECK HARNESS AND CONNECTOR (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY- BODY GROUND)

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
13.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

14.CHECK HARNESS AND CONNECTOR (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY- BODY GROUND)
14.CHECK HARNESS AND CONNECTOR (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY- BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid vehicle battery cover panel LH (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.

Disconnect connector M40 from the hybrid battery junction block assembly.


d.
U158947E02
2.146,1.208 2.552,1.906 false 0.042,0.031 0.24,0.188 0.198,0.156 10 false *a 2.604,1.854 3.365,2.177 0.76,0.323 10 false GND 1.458,1.083 1.76,1.26 0.302,0.177 10 false M40

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
M40-2 (GND) - Body ground Power switch off Below 1 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Battery Junction Block Assembly)


e.

Connect the hybrid battery junction block assembly connector.


f.

Install the No. 1 hybrid vehicle battery cover panel LH.



OK

16.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
15.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

16.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)
16.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid vehicle battery cover panel LH (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.

Disconnect connector M40 from the hybrid battery junction block assembly.


d.
U158950E03
1.385,2.531 1.573,2.792 true 1.198,2.552 0.844,2.802 true 0.323,2.406 0.729,2.594 0.406,0.188 10 false M40 1.406,2.823 1.958,3.104 0.552,0.281 10 false SMRB 0.698,2.823 1.552,3.115 0.854,0.292 10 false GND 0.052,0.031 0.396,0.198 0.344,0.167 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M40-1 (SMRB) - M40-2 (GND) -40 to 80 °C (-40 to 176°F) 25.0 to 59.0 Ω


Text in Illustration
*a Component without harness connected
(Hybrid Battery Junction Block Assembly)


e.

Connect the hybrid battery junction block assembly connector.


f.

Install the No. 1 hybrid vehicle battery cover panel LH.



OK

17.CHECK HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

NG

18.REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY
17.CHECK HYBRID BATTERY JUNCTION BLOCK ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 2 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.
U159041E03
1.292,0.677 0.823,0.677 false 2.26,1.208 2.771,1.708 false 2.563,1.083 2.719,1.26 0.156,0.177 10 false A 1.271,0.354 1.51,0.552 0.24,0.198 10 false P5 0.552,0.604 1.063,0.823 0.51,0.219 10 false CBI 2.813,1.708 2.948,1.875 0.135,0.167 10 false +

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
P5-1 (CBI) - A-1 (+) Power switch off 10 kΩ or higher


HINT:
·

If a system main relay is stuck closed, inspect the hybrid battery junction block assembly without removing it from the vehicle, in order to keep the relay closed.

·

If the result of reading the freeze frame data is A, the hybrid battery junction block assembly must be replaced. Measuring resistance can determine that this is either a present or past malfunction.




d.

Install the No. 2 hybrid battery shield sub-assembly.



OK

18.REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

NG

18.REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY
18.REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

NEXT

19.CHECK HYBRID VEHICLE CONTROL ECU (CHECK FOR NORMAL OPERATION)
19.CHECK HYBRID VEHICLE CONTROL ECU (CHECK FOR NORMAL OPERATION)
a.

Install the service plug grip.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).



e.

Turn the power switch off and wait for 30 seconds or more.


f.

Turn the power switch on (READY).


g.

Enter the following menus: Powertrain / Hybrid Control / Data List / Power Resource VB, VL-Voltage before Boosting.


h.

According to the display on the intelligent tester, read the Data List and monitor the values of "Power Resource VB" and "VL-Voltage before Boosting" for 3 minutes.

Result:
Result Proceed to
Difference between "Power Resource VB" and "VL-Voltage before Boosting" is always less than 100 V. A
Difference between "Power Resource VB" and "VL-Voltage before Boosting" is 100 V or more. B




A

END

B

REPLACE HYBRID VEHICLE CONTROL ECU AND HYBRID BATTERY JUNCTION BLOCK ASSEMBLY