Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0ADC-226  Hybrid Battery Positive Contactor Control Circuit High  


DESCRIPTION

Refer to the description for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

DTC No. INF Code DTC Detection Condition Trouble Area
P0ADC 226 Open or short to +B in the SMRB circuit
·

Wire harness or connector

·

Hybrid battery junction block assembly

·

Power management control ECU



WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

If DTC P0ADC-226 is stored, the power switch cannot be turned on (READY).

·

After the repair, clear the DTCs, perform the following procedure and check that the same DTC (including pending DTC) is not output.

(a)

Turn the power switch off and wait for 30 seconds or more.

(b)

Turn the power switch on (READY) and wait for 30 seconds or more.

(c)

Turn the power switch off and wait for 60 seconds or more.




PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (SMRB STATUS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / SMRB Status.


d.

Read the Data List.

OK:
Tester Display Switch Condition Specified Condition
SMRB Status Power switch on (IG) OFF



e.

Turn the power switch off.



OK

2.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

NG

4.CHECK HARNESS AND CONNECTOR (SMRB VOLTAGE)
2.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid vehicle battery cover panel LH (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.
A266763

Check the connector connections and contact pressure of the relevant terminals for the hybrid battery junction block assembly connector (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

OK:

The connector is connected securely and there are no contact pressure problems.



d.

Install the No. 1 hybrid vehicle battery cover panel LH.



OK

NG

CONNECT SECURELY

4.CHECK HARNESS AND CONNECTOR (SMRB VOLTAGE)
a.

Turn the power switch on (IG).


b.
U158913E02
2.031,1.698 1.583,2.469 false 0.135,0.208 0.406,0.375 0.271,0.167 10 false *a 1.229,2.479 1.729,2.646 0.5,0.167 10 false SMRB 1.917,1.031 2.208,1.188 0.292,0.156 10 false G57

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G57-4 (SMRB) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)


c.

Turn the power switch off.



OK

5.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

NG

6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
5.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

NG

CONNECT SECURELY

6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
a.

Disconnect connector G57 from the power management control ECU.


b.
U158841E02
2.031,2.365 1.667,2.438 false 2.677,2.292 3.031,2.469 0.354,0.177 10 false G57 1.188,2.365 1.625,2.542 0.438,0.177 10 false SMRB 0.146,0.083 0.302,0.26 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G57-4 (SMRB) - Body ground Power switch off 25.0 to 59.0 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)


c.

Connect the power management control ECU connector.



OK

7.CHECK HARNESS AND CONNECTOR (SHORT TO POWER SUPPLY WIRES)

NG

8.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (SHORT TO POWER SUPPLY WIRES)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A263816E03
2.49,2.156 2.615,2.875 false 0.667,2.51 0.604,2.875 false 0.833,2 0.292,2.135 false 0.156,0.073 0.396,0.302 0.24,0.229 10 false *1 0.104,2.052 0.344,2.281 0.24,0.229 10 false *2 0.521,2.896 0.76,3.125 0.24,0.229 10 false *4 2.552,2.896 2.792,3.125 0.24,0.229 10 false *3

Remove the IG2 No. 2 fuse, IGCT No. 2 fuse and AM2 fuse from the No. 2 engine room relay block and No. 2 junction block assembly.

Text in Illustration
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
*2 IG2 No. 2 Fuse
*3 IGCT No. 2 Fuse
*4 AM2 Fuse


c.

Remove the No. 1 hybrid vehicle battery cover panel LH (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


d.
U159020E03
1.948,0.594 2.427,0.906 0.479,0.313 10 false M40

Disconnect connector M40 from the hybrid battery junction block assembly.


e.

Disconnect all the connectors from the power management control ECU.


f.
U183242E01
0.418,1.441 0.682,1.622 0.264,0.181 10 A38 0.369,2.809 0.637,2.990 0.268,0.181 10 +B2 0.958,2.809 1.226,2.990 0.268,0.181 10 +B1 0.187,0.146 0.343,0.328 0.156,0.181 10 *a 1.174,1.447 1.438,1.628 0.264,0.181 10 A39 0.702,2.114 0.545,2.802 false 1.25,2.124 1.115,2.795 false 2.142,2.124 2.122,2.809 false 1.43,2.809 1.672,2.990 0.242,0.181 10 IG2 1.596,2.124 1.575,2.809 false 0.536,3.101 0.945,3.248 0.409,0.146 10 MREL 1.19,2.124 0.792,3.1 false 2.028,2.187 1.775,3.101 false 3.072,2.114 2.895,3.101 false 1.099,3.101 1.451,3.241 0.351,0.140 10 IG2D 1.529,2.124 1.301,3.092 false 1.992,1.448 2.337,1.629 0.345,0.181 10 G57 2.754,1.431 3.108,1.612 0.354,0.181 10 G58 2.179,3.101 2.561,3.241 0.382,0.140 10 AM22 2.688,3.101 3.033,3.241 0.346,0.140 10 IG1D 2.436,2.833 2.817,2.972 0.380,0.139 10 AM21 2.342,2.123 2.405,3.106 false 3.139,2.113 3.184,2.825 false 2.726,2.115 2.684,2.828 false 1.557,3.101 1.904,3.243 0.348,0.142 10 SPDI 1.87,2.809 2.291,2.951 0.421,0.142 10 SMRB 2.941,2.833 3.361,2.975 0.420,0.142 10 ACCD

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G57-4 (SMRB) - A38-2 (+B2) Power switch off 10 kΩ or higher
G57-4 (SMRB) - A39-5 (+B1) Power switch off 10 kΩ or higher
G57-4 (SMRB) - G57-1 (AM22) Power switch off 10 kΩ or higher
G57-4 (SMRB) - G58-7 (AM21) Power switch off 10 kΩ or higher
G57-4 (SMRB) - A39-6 (MREL) Power switch off 10 kΩ or higher
G57-4 (SMRB) - A39-1 (IG2) Power switch off 10 kΩ or higher
G57-4 (SMRB) - G58-1 (ACCD) Power switch off 10 kΩ or higher
G57-4 (SMRB) - G58-2 (IG1D) Power switch off 10 kΩ or higher
G57-4 (SMRB) - A39-2 (IG2D) Power switch off 10 kΩ or higher
G57-4 (SMRB) - G57-14 (SPDI) Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)


g.

Connect the power management control ECU connectors.


h.

Connect the hybrid battery junction block assembly connector.


i.

Install the No. 1 hybrid vehicle battery cover panel LH.


j.

Install the IG2 No. 2 fuse, IGCT No. 2 fuse and AM2 fuse to the No. 2 engine room relay block and No. 2 junction block assembly.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid vehicle battery cover panel LH (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.

Disconnect connector M40 from the hybrid battery junction block assembly.


d.

Disconnect connector G57 from the power management control ECU.


e.
A380673E01
1.833,2.417 2.25,2.667 0.417,0.25 1.458,3.583 1.875,3.833 0.417,0.25 1.479,1.792 2.031,1.792 false 2.615,4.438 2.208,3.771 false 0.094,0.135 0.406,0.333 0.313,0.198 10 false *a 0.135,2.656 0.448,2.854 0.313,0.198 10 false *b 1.021,1.719 1.563,2.083 0.542,0.365 10 false SMRB 1.896,2.458 2.208,2.656 0.313,0.198 10 false G57 1.531,3.625 1.844,3.823 0.313,0.198 10 false M40 2.656,4.385 3.208,4.667 0.552,0.281 10 false SMRB

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
G57-4 (SMRB) - M40-1 (SMRB) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
G57-4 (SMRB) and M40-1 (SMRB) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Rear view of wire harness connector
(to Hybrid Battery Junction Block Assembly)


f.

Connect the power management control ECU connector.


g.

Connect the hybrid battery junction block assembly connector.


h.

Install the No. 1 hybrid vehicle battery cover panel LH.



OK

9.CHECK HARNESS AND CONNECTOR (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid vehicle battery cover panel LH (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.

Disconnect connector M40 from the hybrid battery junction block assembly.


d.
U158947E02
2.146,1.208 2.552,1.906 false 0.042,0.031 0.24,0.188 0.198,0.156 10 false *a 2.604,1.854 3.365,2.177 0.76,0.323 10 false GND 1.458,1.083 1.76,1.26 0.302,0.177 10 false M40

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
M40-2 (GND) - Body ground Power switch off Below 1 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Battery Junction Block Assembly)


e.

Connect the hybrid battery junction block assembly connector.


f.

Install the No. 1 hybrid vehicle battery cover panel LH.



OK

10.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the hybrid battery junction block assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>COMPONENTS).


c.
U158950E03
1.385,2.531 1.573,2.792 true 1.198,2.552 0.844,2.802 true 0.323,2.406 0.729,2.594 0.406,0.188 10 false M40 1.406,2.823 1.958,3.104 0.552,0.281 10 false SMRB 0.698,2.823 1.552,3.115 0.854,0.292 10 false GND 0.052,0.031 0.396,0.198 0.344,0.167 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M40-1 (SMRB) - M40-2 (GND) -40 to 80 °C (-40 to 176°F) 25.0 to 59.0 Ω


Text in Illustration
*a Component without harness connected
(Hybrid Battery Junction Block Assembly)


d.

Install the hybrid battery junction block assembly.



OK

NG

REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY