Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0AE2-773  Hybrid Battery Precharge Contactor Circuit Stuck Closed  


DESCRIPTION

Refer to the description for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

DTC No. INF Code DTC Detection Condition Trouble Area
P0AE2 773 SMRP on the HV battery positive side stuck closed
·

Hybrid battery junction block assembly

·

Inverter with converter assembly

·

POWER MANAGEMENT CONTROL ECU

·

Wire harness and connector



WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

CAUTION / NOTICE / HINT

CAUTION:
·

When performing P0AE2-773 troubleshooting, use either a tool wrapped with vinyl insulation tape or a insulated tool. (It is extremely dangerous when a high-voltage charge passes through a non-insulated tool causing a short.)

·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

If the DTCs are cleared or the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal before performing repairs, turning the power switch on (READY) may cause a malfunction. Do not turn the power switch on (READY).



HINT:

After the repair, clear the DTCs, perform the following procedure and check that the same DTC (including pending DTC) is not output.

1.

Turn the power switch off and wait for 30 seconds or more.

2.

Turn the power switch on (READY) and wait for 30 seconds or more.

3.

Turn the power switch off and wait for 60 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
Only P0AE2-773 is output or P0AE2-773 and DTCs other than the ones in the table below are also output. A
Any of the following DTCs are also output. B


DTC No. Relevant Diagnosis
P0A1A-151, 155, 156, 200, 658, 659, 791, 792, 793 Generator Control Module
P0A1B-163, 164, 168, 193, 511, 512, 661, 786, 794, 795, 796 Drive Motor "A" Control Module
P0A1D-148 Hybrid Powertrain Control Module
P0A3F-243 Drive Motor "A" Position Sensor Circuit
P0A40-500 Drive Motor "A" Position Sensor Circuit Range/Performance
P0A41-245 Drive Motor "A" Position Sensor Circuit Low
P0A4B-253 Generator Position Sensor Circuit
P0A4C-513 Generator Position Sensor Circuit Range/Performance
P0A4D-255 Generator Position Sensor Circuit Low
P0A78-266, 267, 586 Drive Motor "A" Inverter Performance
P0A94-442 DC / DC Converter Performance
P0AE0-228 Hybrid Battery Negative Contactor Control Circuit High
P0AA4-232 Hybrid Battery Negative Contactor Circuit Stuck Closed
P0AE7-224 Hybrid Battery Precharge Contactor Control Circuit High
P0C76-523 Hybrid Battery System Discharge Time Too Long
P2511-149 ECM/PCM Power Relay Sense Circuit Intermittent
P3004-132 High Voltage Power Resource
P324E-788 MG-ECU Power Relay Intermittent Circuit
U0110 (all INF codes)*1 Lost Communication with Drive Motor Control Module "A"

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P0AE2-773 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.




e.

Turn the power switch off.



A

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Read the freeze frame data of DTC P0AE2-773.

Result:
Result Proceed to
"VL-Voltage before Boosting" is 55 V or more. A
"VL-Voltage before Boosting" is less than 55 V. B


HINT:

If VH-Voltage after Boosting is output even when an off command is being sent to the system main relay (positive side), P0AE2-773 is output. If the difference between the "VL-Voltage before Boosting" and the "VH-Voltage after Boosting" is large, it is determined that there is an inverter (VH sensor) malfunction.



e.

Turn the power switch off.



A

3.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

B

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

3.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

5.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

NG

4.CONNECT SECURELY
4.CONNECT SECURELY

NEXT

5.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)
5.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

A

8.CHECK CONNECTOR CONNECTION CONDITION (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

B

6.CONNECT SECURELY

C

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CONNECT SECURELY

NEXT

8.CHECK CONNECTOR CONNECTION CONDITION (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)
7.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

8.CHECK CONNECTOR CONNECTION CONDITION (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)
8.CHECK CONNECTOR CONNECTION CONDITION (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

OK

10.CHECK GROUND WIRE CONNECTION CONDITION (SMR ACTIVATION LOW-VOLTAGE CIRCUIT)

NG

9.CONNECT SECURELY
9.CONNECT SECURELY

NEXT

10.CHECK GROUND WIRE CONNECTION CONDITION (SMR ACTIVATION LOW-VOLTAGE CIRCUIT)
10.CHECK GROUND WIRE CONNECTION CONDITION (SMR ACTIVATION LOW-VOLTAGE CIRCUIT)

OK

12.CHECK POWER MANAGEMENT CONTROL ECU - HYBRIDBATTERY JUNCTION BLOCK ASSEMBLY)

NG

11.CONNECT SECURELY
11.CONNECT SECURELY

NEXT

12.CHECK POWER MANAGEMENT CONTROL ECU - HYBRIDBATTERY JUNCTION BLOCK ASSEMBLY)
12.CHECK POWER MANAGEMENT CONTROL ECU - HYBRIDBATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid vehicle battery cover panel LH (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.

Disconnect connector M40 from the hybrid battery junction block assembly.


d.

Disconnect connector G80 from the power management control ECU.


e.
A380673E12
1.833,2.417 2.25,2.667 0.417,0.25 1.458,3.583 1.875,3.833 0.417,0.25 2.646,1.969 2.094,1.792 false 2.396,4.385 2,3.771 false 0.094,0.135 0.406,0.333 0.313,0.198 10 false *a 0.135,2.656 0.448,2.854 0.313,0.198 10 false *b 2.688,1.906 3.229,2.271 0.542,0.365 10 false SMRP 1.896,2.458 2.208,2.656 0.313,0.198 10 false G80 1.531,3.625 1.844,3.823 0.313,0.198 10 false M40 2.313,4.396 2.865,4.635 0.552,0.24 10 false SMRP

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
G80-3 (SMRP) - M40-4 (SMRP) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
G80-3 (SMRP) and M40-4 (SMRP) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Rear view of wire harness connector
(to Hybrid Battery Junction Block Assembly)


f.

Connect the power management control ECU connector.


g.

Connect the hybrid battery junction block assembly connector.


h.

Install the No. 1 hybrid vehicle battery cover panel LH.



OK

14.CHECK HARNESS AND CONNECTOR (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY- BODY GROUND)

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
13.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

14.CHECK HARNESS AND CONNECTOR (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY- BODY GROUND)
14.CHECK HARNESS AND CONNECTOR (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY- BODY GROUND)

OK

16.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRP)

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
15.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

16.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRP)
16.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRP)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid vehicle battery cover panel LH (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.

Disconnect connector M40 from the hybrid battery junction block assembly.


d.
U158952E03
1.25,2.531 1.615,2.813 false 0.927,2.531 0.729,2.813 false 0.344,2.396 0.813,2.615 0.469,0.219 10 false M40 1.5,2.833 1.844,3 0.344,0.167 10 false GND 0.51,2.865 0.938,3.031 0.427,0.167 10 false SMRP 0.063,0.031 0.406,0.198 0.344,0.167 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M40-4 (SMRP) - M40-2 (GND) -40 to 80 °C (-40 to 176°F) 112 to 274 Ω


Text in Illustration
*a Component without harness connected
(Hybrid Battery Junction Block Assembly)


e.

Connect the hybrid battery junction block assembly connector.


f.

Install the No. 1 hybrid vehicle battery cover panel LH.



OK

17.CHECK HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

NG

18.REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY
17.CHECK HYBRID BATTERY JUNCTION BLOCK ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 2 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.
U159042E03
2.26,1.344 2.74,1.76 false 1.24,0.771 0.854,0.49 false 2.115,1.594 2.313,1.771 0.198,0.177 10 false c1 0.854,0.854 1.167,1.083 0.313,0.229 10 false P4 0.594,0.365 0.854,0.531 0.26,0.167 10 false CEI 2.802,1.688 2.938,1.854 0.135,0.167 10 false -

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
P4-1 (CEI) - c1-1 (-) Power switch off 10 kΩ or higher


HINT:
·

If a system main relay is stuck closed, inspect the hybrid battery junction block assembly without removing it from the vehicle, in order to keep the relay closed.

·

If the result of reading the freeze frame data is A, the hybrid battery junction block assembly must be replaced. Measuring resistance can determine that this is either a present or past malfunction.




d.

Install the No. 2 hybrid battery shield sub-assembly.



OK

18.REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

NG

18.REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY
18.REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

NEXT

19.CHECK POWER MANAGEMENT CONTROL ECU (CHECK FOR NORMAL OPERATION)
19.CHECK POWER MANAGEMENT CONTROL ECU (CHECK FOR NORMAL OPERATION)

A

END

B

REPLACE POWER MANAGEMENT CONTROL ECU AND HYBRID BATTERY JUNCTION BLOCK ASSEMBLY