Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0C30-390  Hybrid Battery Pack State of Charge High  


DESCRIPTION

The hybrid vehicle control ECU monitors its internal operation, it will set DTCs and perform fail-safe control when it detects the following malfunctions.

DTC No. INF Code DTC Detection Condition Trouble Area
P0C30 390 Charge control error
·

Hybrid vehicle control ECU

·

Hybrid battery junction block assembly

·

Battery smart unit

·

Wire harness or connector



WIRING DIAGRAM

A308307E03
1.729,1.177 2.146,1.469 0.417,0.292 10 false VIB 2.104,1.031 2.521,1.323 0.417,0.292 10 false 1 2.125,1.719 2.542,2.01 0.417,0.292 10 false 3 2.125,2.344 2.542,2.635 0.417,0.292 10 false 2 4.906,1.073 5.323,1.365 0.417,0.292 10 false 6 4.927,1.708 5.344,2 0.417,0.292 10 false 5 4.875,2.344 5.292,2.635 0.417,0.292 10 false 12 4.927,3.052 5.344,3.344 0.417,0.292 10 false d1 5.188,3.042 6.583,3.365 1.396,0.323 10 false Battery Smart Unit 0.458,2.865 0.875,3.156 0.417,0.292 10 false d2 0.458,3.031 2.573,3.646 2.115,0.615 10 false Battery Current Sensor (Hybrid Battery Junction Block Assembly) 1.833,1.833 2.25,2.125 0.417,0.292 10 false IB 1.729,2.458 2.146,2.75 0.417,0.292 10 false GIB 5.146,1.073 5.563,1.365 0.417,0.292 10 false VIB 5.135,2.344 5.552,2.635 0.417,0.292 10 false GIB 5.156,1.708 5.573,2 0.417,0.292 10 false IB

Refer to the wiring diagram for DTC P0AFC-123.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0AFC-123

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

When the vehicle is stopped with the power switch on (READY) and the shift lever in D, depress the accelerator pedal. The engine rpm will increase as well as "State of Charge (All Bat)".

If charge current drops, release the accelerator pedal and then depress it again to maintain charging.

2.

Select "Charge Control Value" in the Data List and check that charging stops when "Charge Control Value" reaches 0 kW.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
P0C30-390 only is output. A
DTCs other than P0C30-390 are output. B



e.

Turn the power switch off.



A

2.CHECK BATTERY SMART UNIT (IGCT VOLTAGE)

B

2.CHECK BATTERY SMART UNIT (IGCT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery exhaust duct.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY SMART UNIT>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
U158969E03
1.333,1.229 1.031,0.531 true 1.333,1.292 0.531,2.49 true 0.146,0.125 0.333,0.292 0.188,0.167 10 false *a 0.313,2.521 0.656,2.76 0.344,0.24 10 false GND 0.698,0.406 1.083,0.625 0.385,0.219 10 false IGCT 0.313,1.188 0.823,1.479 0.51,0.292 10 false M39

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M39-3 (IGCT) - M39-6 (GND) Power switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(Battery Smart Unit)

NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

As there might be an intermittent malfunction in the battery smart unit power source circuit, inspect the following even if the measured voltage is as specified:


·

Installation condition of fuse(s) (before removing fuse(s)) (IGCT circuit)

·

Fuse condition (before and after removing fuse(s)) (IGCT circuit)

·

Connection condition of connectors (IGCT circuit)

·

Wire harness condition (IGCT circuit)

·

Wire harness condition (GND circuit)



f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the No. 1 hybrid battery exhaust duct.



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY - BATTERY SMART UNIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY SMART UNIT POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY - BATTERY SMART UNIT)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY SMART UNIT>REMOVAL


c.

Remove the No. 2 hybrid battery shield sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


d.

Disconnect only the d1 connector of the battery smart unit.


e.
A389837E01
2.26,0.969 2.604,1.156 0.344,0.188 2.354,0.99 2.667,1.188 0.313,0.198 10 false d2

Disconnect the d2 battery current sensor connector from the hybrid battery junction block assembly.


f.
U158972E03
1.594,1.667 2.292,1.188 false 1.979,3.76 2.594,3.708 false 1.479,1.667 1.844,1 false 1.531,3.844 0.917,3.188 false 1.469,1.833 1.083,2.135 false 1.771,3.75 2.427,3.188 false 1.125,1.125 1.354,1.323 0.229,0.198 10 false *a 1.156,2.698 1.385,2.896 0.229,0.198 10 false *b 2.365,1.083 2.594,1.271 0.229,0.188 10 false IB 2.656,3.615 2.885,3.802 0.229,0.188 10 false IB 1.906,0.896 2.177,1.083 0.271,0.188 10 false VIB 0.604,3.104 0.875,3.292 0.271,0.188 10 false VIB 0.781,2.063 1.073,2.26 0.292,0.198 10 false GIB 2.531,3.104 2.823,3.302 0.292,0.198 10 false GIB 0.708,1.573 0.896,1.719 0.188,0.146 10 false d1 0.677,3.604 0.906,3.75 0.229,0.146 10 false d2

Measure the resistance according to the value(s) in the tables below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
d1-5 (IB) - d2-3 (IB) Power switch off Below 1 Ω
d1-12 (GIB) - d2-2 (GIB) Power switch off Below 1 Ω
d1-6 (VIB) - d2-1 (VIB) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
d1-5 (IB) or d2-3 (IB) - Body ground and other terminals Power switch off 10 kΩ or higher
d1-12 (GIB) or d2-2 (GIB) - Body ground and other terminals Power switch off 10 kΩ or higher
d1-6 (VIB) or d2-1 (VIB) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Battery Smart Unit)
*b Front view of wire harness connector
(to Hybrid Battery Junction Block Assembly)

HINT:

Because the battery harness is not available as a supply part, if the harness cannot be repaired, replace the HV battery assembly.



g.

Connect the battery smart unit connector.


h.

Connect the battery current sensor connector to the hybrid battery junction block assembly.


i.

Install the No. 2 hybrid battery shield sub-assembly.


j.

Install the No. 1 hybrid battery shield sub-assembly.



OK

4.CHECK BATTERY SMART UNIT (VIB VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK BATTERY SMART UNIT (VIB VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY SMART UNIT>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
U158965E03
0.583,0.448 0.917,0.885 true 0.917,0.969 0.625,1.719 true 0.115,0.073 0.302,0.24 0.188,0.167 10 false *a 0.302,0.375 0.552,0.615 0.25,0.24 10 false VIB 0.49,1.75 0.844,1.969 0.354,0.219 10 false GIB 1.01,0.146 1.313,0.333 0.302,0.188 10 false d1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
d1-6 (VIB) - d1-12 (GIB) Power switch on (IG) 4.6 to 5.4 V


Text in Illustration
*a Component with harness connected
(Battery Smart Unit)

NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the No. 1 hybrid battery shield sub-assembly.



OK

5.CHECK BATTERY SMART UNIT (GIB TERMINAL - GND TERMINAL)

NG

7.CHECK BATTERY SMART UNIT (VIB VOLTAGE)
5.CHECK BATTERY SMART UNIT (GIB TERMINAL - GND TERMINAL)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY SMART UNIT>REMOVAL


c.

Disconnect connectors d1 and M39 from the battery smart unit.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A467959E01
0.333,0.823 0.833,1.073 0.5,0.25 0.198,3.177 0.698,3.427 0.5,0.25 0.875,4.167 1.229,3.344 true 1.375,0.969 0.604,2.052 true 0.208,0.188 0.479,0.365 0.271,0.177 10 false *a 0.729,4.198 1.052,4.406 0.323,0.208 10 false GIB 0.438,0.865 0.833,1.083 0.396,0.219 10 false M39 0.396,3.219 0.656,3.396 0.26,0.177 10 false d1 0.438,2.083 0.844,2.323 0.406,0.24 10 false GND

Measure the resistance according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
d1-12(GIB) -M39-6(GND) Power switch off Below 1 Ω


Text in Illustration
*a Component without harness connected
(Battery Smart Unit)


e.

Connect the battery smart unit connectors.


f.

Install the No. 1 hybrid battery shield sub-assembly.



OK

6.CHECK HYBRID VEHICLE CONTROL ECU (POWER RESOURCE IB, BATT PACK CURRENT VAL)

NG

REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

6.CHECK HYBRID VEHICLE CONTROL ECU (POWER RESOURCE IB, BATT PACK CURRENT VAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).

NOTICE:

During the inspection, make sure to only turn the power switch on (IG). Do not turn the power switch on (READY).



c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Power Resource IB, Batt Pack Current Val.


d.

With the power switch on (IG), monitor Data List item "Power Resource IB" and "Batt Pack Current" for 1 minute.

Result:
Result Proceed to
The value of Data List item "Power Resource IB" and "Batt Pack Current" is -0.5 A or less or 0.5 A or more. A
Other than above B



e.

Turn the power switch off.



A

B

7.CHECK BATTERY SMART UNIT (VIB VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY SMART UNIT>REMOVAL


c.

Remove the No. 2 hybrid battery shield sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


d.
U159017E02
2.354,0.969 2.563,1.135 0.208,0.167 10 true d2

Disconnect the d2 battery current sensor connector from the hybrid battery junction block assembly.


e.

Connect the cable to the negative (-) auxiliary battery terminal.


f.

Turn the power switch on (IG).


g.
U158965E02
0.583,0.448 0.917,0.885 true 0.917,0.969 0.625,1.719 true 0.115,0.073 0.302,0.24 0.188,0.167 10 false *a 0.302,0.375 0.552,0.615 0.25,0.24 10 false VIB 0.49,1.75 0.844,1.969 0.354,0.219 10 false GIB 1.01,0.146 1.313,0.333 0.302,0.188 10 false d1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
d1-6(VIB) - d1-12(GIB) Power switch on (IG) 4.6 to 5.4 V


Text in Illustration
*a Component with harness connected
(Battery Smart Unit)

NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


j.

Connect the battery current sensor connector to the hybrid battery junction block assembly.


k.

Install the No. 2 hybrid battery shield sub-assembly.


l.

Install the No. 1 hybrid battery shield sub-assembly.



OK

REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

NG