This DTC indicates that the power management control ECU monitors the +B power source voltage to detect an instantaneous interruption.
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P2511 | 149 | When the power switch is on (READY), the power management control ECU is reset. | ·
Wire harness or connector ·
Power management control ECU |
Refer to the wiring diagram for DTC P3110-223 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P3110-223).
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Turn the power switch on (READY) and wait for 30 seconds or more.
(If the DTC is not output, drive the vehicle on urban roads according to the freeze frame data item "Vehicle Spd" for approximately 5 minutes.)
Confirm whether the auxiliary battery terminals have been disconnected recently.
| Result | Proceed to |
|---|---|
| Terminals have been disconnected. | A |
| Terminals have not been disconnected. | B |
A
B
Turn the power switch on (READY) from off.
Confirm that the master warning light illuminates.
| Result | Proceed to |
|---|---|
| Master warning light illuminates. | A |
| Master warning light does not illuminates. | B |
DTC P2511-149 may be stored after disconnecting and reconnecting the auxiliary battery terminals. If this happens, the DTC will not be output if the power switch is turned off and then on (READY) again. In this case, clear DTCs to complete the inspection.
Turn the power switch off.
A
B
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Read and record the DTCs and freeze frame data.
Clear the DTCs and freeze frame data.
Turn the power switch off.
NEXT
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| DTC P2511-149 is output again. | A |
| DTCs other than P2511-149 are also output. | B |
Turn the power switch off.
A
B
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
Check the connection of the auxiliary battery terminal.
The terminal is connected securely and there is no contact problem.
OK
NG
OK
NG
Remove the IGCT relay from the No. 2 engine room relay block and No. 2 junction block assembly.
Disconnect connectors A38 and A39 from power management control ECU.
| *1 | No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly | *2 | IGCT Relay |
| *a | Rear view of wire harness connector
(to Power Management Control ECU) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A39-5 (+B1) - 5 (IGCT relay) | Power switch off | Below 1 Ω |
| A38-2 (+B2) - 5 (IGCT relay) | Power switch off | Below 1 Ω |
Install the IGCT relay.
Connect the power management control ECU connectors.
OK
NG
Check for intermittent problems (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).
Check the connection and terminal contact pressure of connectors and wire harnesses between the power management control ECU and the No. 2 engine room relay block and No. 2 junction block assembly.
When the power switch is on (READY), jiggle the connectors and wire harnesses between the power management control ECU and the No. 2 engine room relay block and No. 2 junction block assembly.
| Result | Proceed to |
|---|---|
| Problem symptom does not recur. | A |
| Problem symptom recurs. | B |
A
B