Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3004-131  High Voltage Power Resource  


DESCRIPTION

Refer to the description for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

The hybrid vehicle control ECU monitors the high-voltage wiring between the HV battery and the inverter with converter assembly and detects the following malfunction.

DTC No. INF Code DTC Detection Condition Trouble Area
P3004 131 One of the following occurs during pre-charge (the time from when SMRP turns on until SMRG turns on):
·

Electric battery fuse in the service plug grip has an open circuit

·

Service plug grip is not installed

·

SMRP remains open

·

SMRB remains open

·

Precharge resistor has an open circuit

·

High voltage cable has an open circuit


·

Hybrid battery junction block assembly

·

Frame wire

·

Inverter with converter assembly

·

HV battery

·

Wire harness or connector



WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AA6-526 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA6-526).

Refer to the wiring diagram for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).


CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs, perform the following procedure and check that the same DTC (including pending DTC) is not output.

1.

Turn the power switch off and wait for 30 seconds or more.

2.

Turn the power switch on (READY) and wait for 30 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
Only P3004-131 is output or P3004-131 and DTCs other than the ones in the table below are also output. A
DTCs shown in Table 1 are output simultaneously. B
DTCs shown in Table 2 are output simultaneously. C


Table 1
DTC No. Relevant Diagnosis
P06E6-164 Sensor Power Supply "C" Circuit/Open
P0A1A-151, 658 Generator Control Module
P0A1B-786 Drive Motor "A" Control Module
P0A1D-148 Hybrid Powertrain Control Module
P0ADB-227 Hybrid Battery Positive Contactor Control Circuit Low
P0ADC-226 Hybrid Battery Positive Contactor Control Circuit High
P0ADF-229 Hybrid Battery Negative Contactor Control Circuit Low
P0AE0-228 Hybrid Battery Negative Contactor Control Circuit High
P0AE6-225 Hybrid Battery Precharge Contactor Control Circuit Low
P0AE7-224 Hybrid Battery Precharge Contactor Control Circuit High
P0C76-523 Hybrid Battery System Discharge Time Too Long
P0CA3-442 DC/DC Converter Step Up Voltage Performance
P0D2E-586 Drive Motor "A" Inverter Voltage Sensor Circuit Range/Performance
P0D2F-266 Drive Motor "A" Inverter Voltage Sensor Circuit Low
P0D30-267 Drive Motor "A" Inverter Performance
P1C2A-155 Generator A/D Converter Circuit
P1C73-512 Sensor Standard Voltage "F" Circuit/Open
P1CA6-156 Generator Control Module Malfunction
P1CA7-193 Drive Motor Control Module Malfunction
P2511-149 HV CPU Power Relay Sense Circuit Intermittent No Continuity
P3004-800, 801 High Voltage Power Resource
P3133-659 Communication Error from Generator to Drive Motor "A"
P3134-661 Communication Error from Drive Motor "A" to Generator
P324E-788 MG-ECU Power Relay Intermittent Circuit
U0110 (all INF codes)*1 Lost Communication with Drive Motor Control Module "A"

Table 2
DTC No. Relevant Diagnosis
P0A95-123 High Voltage Fuse
P0ABF-123 Hybrid Battery Pack Current Sensor Circuit
P0AC0-123 Hybrid Battery Pack Current Sensor Circuit Range / Performance
P0AC1-123 Hybrid Battery Pack Current Sensor "A" Circuit Low
P0AC2-123 Hybrid Battery Pack Current Sensor "A" Circuit High
P0AFC-123 Hybrid Battery Pack Sensor Module
P0B3D-123 Hybrid Battery Voltage Sensor "A" Circuit Low
P0B42-123 Hybrid Battery Voltage Sensor "B" Circuit Low
P0B47-123 Hybrid Battery Voltage Sensor "C" Circuit Low
P0B4C-123 Hybrid Battery Voltage Sensor "D" Circuit Low
P0B51-123 Hybrid Battery Voltage Sensor "E" Circuit Low
P0B56-123 Hybrid Battery Voltage Sensor "F" Circuit Low
P0B5B-123 Hybrid Battery Voltage Sensor "G" Circuit Low
P0B60-123 Hybrid Battery Voltage Sensor "H" Circuit Low
P0B65-123 Hybrid Battery Voltage Sensor "I" Circuit Low
P0B6A-123 Hybrid Battery Voltage Sensor "J" Circuit Low
P0B6F-123 Hybrid Battery Voltage Sensor "K" Circuit Low
P308A-123 Hybrid Battery Voltage Sensor All Circuits Low
U029A-123 Lost Communication with Hybrid Battery Pack Sensor Module

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P3004-131 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.




e.

Turn the power switch off.



A

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

C

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Read the freeze frame data of DTC P3004-131.

Result:
Result Proceed to
Both of the following conditions are met:
·

Post-boost voltage (VH-Voltage after Boosting) is below 50 V.

·

Difference between HV battery voltage (Power Resource VB) and pre-boost voltage (VL-Voltage before Boosting) is 50 V or less.


A
Other than above B



e.

Turn the power switch off.



A

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

B

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

4.CHECK INVERTER WITH CONVERTER ASSEMBLY (FRAME WIRE CONNECTION CONDITION)

NG

CONNECT SECURELY

4.CHECK INVERTER WITH CONVERTER ASSEMBLY (FRAME WIRE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258644

Remove the inverter terminal cover from the inverter with converter assembly.


c.
A258645

Remove the inverter cover from the inverter with converter assembly.


d.
U158934E02
1.708,1.031 1.906,1.208 0.198,0.177 10 false P1 0.667,0.917 0.802,1.094 0.135,0.177 10 true A 1.823,0.615 2,0.833 0.177,0.219 10 true B 1.094,1.313 1.229,1.49 0.135,0.177 10 false A 0.813,0.167 0.948,0.344 0.135,0.177 10 true B

Check the connector P1 connection condition between the frame wire and the inverter with converter assembly.


Torque:
Bolt A : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Bolt B : 9.2 N*m (94 kgf*cm, 81 in.*lbf)

e.

Disconnect connector P1 of the frame wire from the inverter with converter assembly.


f.

Check for arc marks on the terminals of the frame wire.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



g.

Connect the frame wire to the inverter with converter assembly.


h.

Install the inverter cover.


i.

Install the inverter terminal cover.



A

5.CHECK HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (FRAME WIRE CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

5.CHECK HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (FRAME WIRE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid vehicle battery cover panel LH (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.
U159050E03
1.531,0.302 1.917,0.594 0.385,0.292 10 false P5 1.365,1.063 1.76,1.344 0.396,0.281 10 false P4

Check the connector P5 and connector P4 connection condition between the frame wire and the hybrid battery junction block assembly.


d.

Disconnect connector P5 and connector P4 of the frame wire from the hybrid battery junction block assembly.


e.

Check for arc marks on the terminals of the frame wire.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



f.

Connect the frame wire to the hybrid battery junction block assembly.


g.

Install the No. 1 hybrid vehicle battery cover panel LH.



A

6.CHECK FRAME WIRE (INVERTER WITH CONVERTER ASSEMBLY - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

6.CHECK FRAME WIRE (INVERTER WITH CONVERTER ASSEMBLY - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258644

Remove the inverter terminal cover from the inverter with converter assembly.


c.
A258645

Remove the inverter cover from the inverter with converter assembly.


d.
U158935E02
1.698,0.979 1.896,1.156 0.198,0.177 10 false P1

Disconnect connector P1 of the frame wire from the inverter with converter assembly.


e.

Remove the No. 1 hybrid vehicle battery cover panel LH (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


f.
U159050E03
1.531,0.302 1.917,0.594 0.385,0.292 10 false P5 1.365,1.063 1.76,1.344 0.396,0.281 10 false P4

Disconnect connector P5 and connector P4 of the frame wire from the hybrid battery junction block assembly.


g.
U158990E02
2.073,1.771 2.344,1.771 false 1.094,1.771 1.365,1.771 false 1,3.469 1,3.188 false 1.833,3.469 1.833,3.188 false 0.531,1.042 0.729,1.219 0.198,0.177 10 false P1 0.896,2.604 1.094,2.781 0.198,0.177 10 false P5 1.729,2.604 1.927,2.781 0.198,0.177 10 false P4 0.167,0.146 0.375,0.344 0.208,0.198 10 false *a 0.167,2.323 0.375,2.521 0.208,0.198 10 false *b 2.406,1.688 2.708,1.865 0.302,0.177 10 false CBI 0.792,1.688 1.094,1.865 0.302,0.177 10 false CEI 0.854,3.49 1.156,3.667 0.302,0.177 10 false CBI 1.667,3.479 1.969,3.656 0.302,0.177 10 false CEI

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
P5-1 (CBI) - P1-2 (CBI) Power switch off Below 1 Ω
P4-1 (CEI) - P1-1 (CEI) Power switch off Below 1 Ω


Text in Illustration
*a Frame wire
(Inverter with Converter Assembly Side)
*b Frame wire
(Hybrid Battery Junction Block Assembly Side)


h.

Connect the frame wire to the hybrid battery junction block assembly.


i.

Install the No. 1 hybrid vehicle battery cover panel LH.


j.

Connect the frame wire to the inverter with converter assembly.


k.

Install the inverter cover.


l.

Install the inverter terminal cover.



OK

7.CHECK HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (HV BATTERY HIGH VOLTAGE TERMINAL CONNECTION CONDITION)

NG

7.CHECK HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (HV BATTERY HIGH VOLTAGE TERMINAL CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 2 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.
A267591

Check the connections between the HV battery high voltage terminals and the hybrid battery junction block assembly.

Specified Condition:

5.4 N*m (55 kgf*cm, 48 in.*lbf)



d.

Disconnect the HV battery high voltage terminals from the hybrid battery junction block assembly.


e.

Check for arc marks on the terminals of the HV battery high voltage terminals.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



f.

Connect the HV battery high voltage terminals.


g.

Install the No. 2 hybrid battery shield sub-assembly.



A

8.CHECK HV BATTERY

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

8.CHECK HV BATTERY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 2 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.
A380686E01
2.615,1.25 3.052,1.135 false 2.573,1.427 3.052,1.51 false 0.875,2.771 1.375,2.979 false 0.844,4.146 1.375,3.729 false 3.115,1.031 3.375,1.25 0.26,0.219 10 false + 3.094,1.417 3.354,1.635 0.26,0.219 10 false - 0.708,2.667 0.969,2.885 0.26,0.219 10 false 2 0.698,4.063 0.958,4.281 0.26,0.219 10 false 1 2.5,0.854 2.708,1.094 0.208,0.24 10 false A 2.552,1.771 2.76,2.01 0.208,0.24 10 false c1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A-1 (+) - Service plug grip terminal 1 Power switch off 66 V or higher
c1-1 (-) - Service plug grip terminal 2 Power switch off 54 V or higher


CAUTION:

Do not allow the probes of the electrical tester to contact each other during this inspection.



d.

Install the No. 2 hybrid battery shield sub-assembly.



OK

9.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)

NG

9.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector G80 from the hybrid vehicle control ECU.


c.

Remove the No. 1 hybrid vehicle battery cover panel LH (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


d.

Disconnect the connector M40 that drives the system main relay of the hybrid battery junction block assembly.

HINT:

Before disconnecting the connector M40 that drives the system main relay of the hybrid battery junction block assembly, make sure that the connector is securely engaged.



e.
A380673E14
1.833,2.417 2.25,2.667 0.417,0.25 1.458,3.583 1.875,3.833 0.417,0.25 1.479,1.792 2.031,1.792 false 2.615,4.438 2.208,3.771 false 2.094,1.792 2.646,1.792 false 1.229,4.333 2,3.771 false 0.094,0.135 0.406,0.333 0.313,0.198 10 false *a 0.135,2.656 0.448,2.854 0.313,0.198 10 false *b 1.021,1.719 1.563,2.083 0.542,0.365 10 false SMRB 1.917,2.458 2.229,2.656 0.313,0.198 10 false G80 1.531,3.625 1.844,3.823 0.313,0.198 10 false M40 2.656,4.385 3.208,4.667 0.552,0.281 10 false SMRB 2.708,1.719 3.25,2.083 0.542,0.365 10 false SMRP 0.979,4.365 1.5,4.656 0.521,0.292 10 false SMRP

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G80-4 (SMRB) - M40-1 (SMRB) Power switch off Below 1 Ω
G80-3 (SMRP) - M40-4 (SMRP) Power switch off Below 1 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Rear view of wire harness connector
(to Hybrid Battery Junction Block Assembly)


f.

Connect the hybrid battery junction block assembly connector.


g.

Install the No. 1 hybrid vehicle battery cover panel LH.


h.

Connect the hybrid vehicle control ECU connector.



OK

10.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the hybrid battery junction block assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>COMPONENTS).


c.
A381348E01
1.01,2.792 1.208,2.542 false 1.604,2.781 1.375,2.552 false 3.021,1.438 2.729,1.208 false 0.573,0.729 0.833,0.823 false 0.281,0.656 0.698,0.948 0.417,0.292 10 false CBI 1.146,0.448 1.563,0.74 0.417,0.292 10 false P5 0.073,0.083 0.49,0.375 0.417,0.292 10 false *a 3.031,0.823 3.281,1.104 0.25,0.281 10 false A 3.052,1.375 3.427,1.667 0.375,0.292 10 false + 1.5,2.813 2.125,3.083 0.625,0.271 10 false SMRB 0.823,2.813 1.24,3.104 0.417,0.292 10 false GND 0.177,2.167 0.594,2.458 0.417,0.292 10 false M40

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P5-1 (CBI) - A-1 (+) Auxiliary battery voltage is applied between terminals M40-1 (SMRB) and M40-2 (GND) Below 1 Ω


Text in Illustration
*a Component without harness connected
(Hybrid Battery Junction Block Assembly)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M40-1 (SMRB) - M40-2 (GND) -40 to 80 °C (-40 to 176°F) 25.0 to 59.0 Ω



e.

Install the hybrid battery junction block assembly.



OK

11.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRP)

NG

REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

11.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRP)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the hybrid battery junction block assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>COMPONENTS).


c.
U158954E03
1.24,2.531 1.604,2.813 true 0.927,2.542 0.802,2.771 true 0.823,0.938 1.552,0.563 false 2.75,1.396 3.156,0.938 false 0.188,0.969 0.406,1.135 0.219,0.167 10 false P4 0.375,2.375 0.667,2.542 0.292,0.167 10 false M40 2.854,1.656 3.042,1.823 0.188,0.167 10 false c1 1.479,2.833 1.823,3 0.344,0.167 10 false GND 0.604,2.823 1.063,2.99 0.458,0.167 10 false SMRP 0.125,0.073 0.469,0.24 0.344,0.167 10 false *a 1.615,0.448 1.917,0.625 0.302,0.177 10 false CEI 3.208,0.813 3.292,0.99 0.083,0.177 10 false -

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P4-1 (CEI) - c1-1 (-) Auxiliary battery voltage is applied between terminals M40-4 (SMRP) and M40-2 (GND) 28.5 to 31.5 Ω


Text in Illustration
*a Component without harness connected
(Hybrid Battery Junction Block Assembly)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M40-4 (SMRP) - M40-2 (GND) -40 to 80 °C (-40 to 176°F) 112 to 274 Ω



e.

Install the hybrid battery junction block assembly.



OK

12.CHECK FOR INTERMITTENT PROBLEMS

NG

REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

12.CHECK FOR INTERMITTENT PROBLEMS

(See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS)

HINT:
·

Since 2 trip detection logic is used, the DTC detection condition must be met twice.

·

If DTC P3004-131 is output again after performing the inspection, replace the hybrid vehicle converter. If DTC P3004-131 is not output again, replace the hybrid battery junction block assembly.




OK

REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

NG

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS