Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3107-214  Lost Communication with Airbag System Control Module  


DESCRIPTION

Refer to the description for DTC P3107-213 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P3107-213).


DTC No. INF Code DTC Detection Condition Trouble Area
P3107 214 Open or short to +B in the communication circuit
·

Wire harness or connector

·

Airbag sensor assembly

·

Power management control ECU



WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

Refer to the wiring diagram for DTC P3107-213 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P3107-213).

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG) and wait for 15 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT (SRS AIRBAG)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body / SRS Airbag / DTC.


d.

Check if DTCs are output.


Result:
Result Proceed to
Airbag system DTCs are not output. A
Airbag system DTCs are output. B


e.

Turn the power switch off.



A

2.CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)

B

2.CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)

A

3.CLEAR DTC

B

6.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)
3.CLEAR DTC

NEXT

4.CHECK DTC OUTPUT (HYBRID CONTROL)
4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
P3107-214 is not output. A
P3107-214 is output again. B



e.

Turn the power switch off.



A

5.CHECK FOR INTERMITTENT PROBLEMS

B

5.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

6.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

7.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG SENSOR ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

7.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG SENSOR ASSEMBLY CONNECTOR)
a.
U158888E02
1.208,1.042 1.479,1.688 false 0.177,0.073 0.427,0.302 0.25,0.229 10 false *a 1.281,1.708 1.854,1.938 0.573,0.229 10 false GSW2 0.958,0.375 1.25,0.531 0.292,0.156 10 false G18

Check the connector connections and contact pressure of the relevant terminals for the airbag sensor assembly connectors.

Text in Illustration
*a Component with harness connected
(Airbag Sensor Assembly)

OK:

The connectors are connected securely and there are no contact pressure problems.




OK

8.CHECK HARNESS AND CONNECTOR (+B SHORT)

NG

CONNECT SECURELY

8.CHECK HARNESS AND CONNECTOR (+B SHORT)
a.
A263605E02
0.677,2.51 0.5,2.833 false 2.552,2.115 3.125,1.75 false 0.188,0.094 0.479,0.302 0.292,0.208 10 false *1 0.396,2.844 0.688,3.052 0.292,0.208 10 false *2 3.135,1.646 3.344,1.854 0.208,0.208 10 false *3

Remove the IGCT No. 2 fuse and AM2 fuse from the No. 2 engine room relay block and No. 2 junction block assembly.

Text in Illustration
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
*2 AM2 Fuse
*3 IGCT No. 2 Fuse


b.
U158887E03
0.094,0.031 0.344,0.25 0.25,0.219 10 false *a 0.49,1.365 0.781,1.531 0.292,0.167 10 false G18

Disconnect connector G18 from the airbag sensor assembly.

Text in Illustration
*a Component without harness connected
(Airbag Sensor Assembly)


c.
U183245E01
0.165,0.134 0.330,0.299 0.165,0.165 10 *a 1.881,2.396 2.261,2.562 0.380,0.165 10 ABFS 0.646,0.979 0.925,1.142 0.279,0.163 10 A38 1.251,0.979 1.529,1.142 0.279,0.163 10 A39 1.899,0.979 2.192,1.142 0.294,0.163 10 G57 2.491,0.979 2.803,1.142 0.312,0.163 10 G58 0.395,2.396 0.663,2.578 0.268,0.181 10 +B2 1.026,2.396 1.294,2.578 0.268,0.181 10 +B1 0.944,1.701 0.557,2.412 false 1.339,1.693 1.199,2.389 false 1.494,2.396 1.736,2.578 0.242,0.181 10 IG2 1.673,1.701 1.625,2.39 false 0.564,2.86 0.972,3.007 0.409,0.146 10 MREL 1.269,1.701 0.815,2.847 false 1.925,1.775 1.81,2.851 false 2.785,1.702 2.943,2.851 false 1.14,2.86 1.491,3.000 0.351,0.140 10 IG2D 1.61,1.701 1.326,2.851 false 2.193,2.86 2.575,3.000 0.382,0.140 10 AM22 2.75,2.86 3.095,3.000 0.346,0.140 10 IG1D 2.421,2.42 2.801,2.559 0.380,0.139 10 AM21 2.249,1.701 2.423,2.845 false 2.852,1.7 3.162,2.412 false 2.45,1.703 2.659,2.415 false 1.597,2.86 1.945,3.002 0.348,0.142 10 SPDI 2.936,2.42 3.356,2.562 0.420,0.142 10 ACCD 2.247,1.906 2.116,2.389 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G57-29 (ABFS) - A38-2 (+B2) Power switch off 10 kΩ or higher
G57-29 (ABFS) - A39-1 (IG2) Power switch off 10 kΩ or higher
G57-29 (ABFS) - A39-2 (IG2D) Power switch off 10 kΩ or higher
G57-29 (ABFS) - A39-5 (+B1) Power switch off 10 kΩ or higher
G57-29 (ABFS) - A39-6 (MREL) Power switch off 10 kΩ or higher
G57-29 (ABFS) - G57-1 (AM22) Power switch off 10 kΩ or higher
G57-29 (ABFS) - G57-14 (SPDI) Power switch off 10 kΩ or higher
G57-29 (ABFS) - G58-1 (ACCD) Power switch off 10 kΩ or higher
G57-29 (ABFS) - G58-2 (IG1D) Power switch off 10 kΩ or higher
G57-29 (ABFS) - G58-7 (AM21) Power switch off 10 kΩ or higher


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)


d.

Connect the airbag sensor assembly connector.


e.

Install the IGCT No. 2 fuse and AM2 fuse.



OK

9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AIRBAG SENSOR ASSEMBLY)

NG

11.CHECK HARNESS AND CONNECTOR (SHORT TO POWER SUPPLY WIRES)
9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect connector G57 from the power management control ECU.


b.

Disconnect connector G18 from the airbag sensor assembly.


c.
U183222E02
2.25,1.823 2.552,2.052 false 1.281,3.854 1.781,4.229 false 0.063,0 0.333,0.198 0.271,0.198 10 false *a 0.083,2.385 0.354,2.583 0.271,0.198 10 false *b 1.313,1.573 1.604,1.74 0.292,0.167 10 false G57 0.427,3.729 0.729,3.896 0.302,0.167 10 false G18 2.594,1.99 3.063,2.188 0.469,0.198 10 false ABFS 1.802,4.177 2.438,4.396 0.635,0.219 10 false GSW2

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
G57-29 (ABFS) - G18-14 (GSW2) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
G57-29 (ABFS) or G18-14 (GSW2) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)

HINT:

As necessary, check that there is no short to power supply wires when performing the above wire harness inspection.



d.

Connect the airbag sensor assembly connector.


e.

Connect the power management control ECU connector.



OK

10.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK POWER MANAGEMENT CONTROL ECU
a.
U158887E03
0.094,0.031 0.344,0.25 0.25,0.219 10 false *a 0.49,1.365 0.781,1.531 0.292,0.167 10 false G18

Disconnect connector G18 from the airbag sensor assembly.

Text in Illustration
*a Component without harness connected
(Airbag Sensor Assembly)


b.

Turn the power switch on (IG).


c.
U183247E02
2.24,1.906 2.521,2.531 false 2.417,2.552 2.906,2.729 0.49,0.177 10 false ABFS 0.135,0.052 0.292,0.229 0.156,0.177 10 false *a 1.927,0.969 2.229,1.146 0.302,0.177 10 false G57

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G57-29 (ABFS) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)

NOTICE:

Turning the power switch on (IG) with the airbag sensor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the power switch off.


e.

Connect the airbag sensor assembly connector.



OK

NG

11.CHECK HARNESS AND CONNECTOR (SHORT TO POWER SUPPLY WIRES)
a.
A263605E02
0.677,2.51 0.5,2.833 false 2.552,2.115 3.125,1.75 false 0.188,0.094 0.479,0.302 0.292,0.208 10 false *1 0.396,2.844 0.688,3.052 0.292,0.208 10 false *2 3.135,1.646 3.344,1.854 0.208,0.208 10 false *3

Remove the IGCT No. 2 fuse and AM2 fuse from the No. 2 engine room relay block and No. 2 junction block assembly.

Text in Illustration
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
*2 AM2 Fuse
*3 IGCT No. 2 Fuse


b.
U158887E03
0.094,0.031 0.344,0.25 0.25,0.219 10 false *a 0.49,1.365 0.781,1.531 0.292,0.167 10 false G18

Disconnect connector G18 from the airbag sensor assembly.

Text in Illustration
*a Component without harness connected
(Airbag Sensor Assembly)


c.

Disconnect all the connectors from the power management control ECU.


d.
U183241E02
2.333,2.333 2.365,3.073 true 0.698,2.115 0.49,2.771 true 1.24,2.125 1.104,2.802 true 1.583,2.135 1.563,2.823 true 1.177,2.125 0.781,3.104 true 2.01,2.208 1.75,3.115 true 3.042,2.115 2.844,3.094 true 1.51,2.125 1.281,3.094 true 2.323,2.125 2.125,2.802 true 3.115,2.125 3.167,2.844 true 2.708,2.115 2.667,2.823 true 0.427,1.448 0.688,1.625 0.26,0.177 10 false A38 0.188,0.104 0.344,0.281 0.156,0.177 10 false *a 1.188,1.448 1.448,1.625 0.26,0.177 10 false A39 2.01,1.448 2.333,1.625 0.323,0.177 10 false G57 2.781,1.438 3.104,1.615 0.323,0.177 10 false G58 2.146,3.094 2.542,3.271 0.396,0.177 10 false ABFS 0.333,2.781 0.604,2.958 0.271,0.177 10 false +B2 0.958,2.813 1.229,2.99 0.271,0.177 10 false +B1 1.427,2.833 1.667,3.01 0.24,0.177 10 false IG2 0.531,3.104 0.938,3.25 0.406,0.146 10 false MREL 1.104,3.115 1.458,3.25 0.354,0.135 10 false IG2D 1.885,2.802 2.271,2.938 0.385,0.135 10 false AM22 2.667,3.115 3.01,3.25 0.344,0.135 10 false IG1D 2.438,2.823 2.813,2.958 0.375,0.135 10 false AM21 1.552,3.125 1.896,3.271 0.344,0.146 10 false SPDI 2.938,2.844 3.354,2.99 0.417,0.146 10 false ACCD

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G57-29 (ABFS) - A38-2 (+B2) Power switch off 10 kΩ or higher
G57-29 (ABFS) - A39-1 (IG2) Power switch off 10 kΩ or higher
G57-29 (ABFS) - A39-2 (IG2D) Power switch off 10 kΩ or higher
G57-29 (ABFS) - A39-5 (+B1) Power switch off 10 kΩ or higher
G57-29 (ABFS) - A39-6 (MREL) Power switch off 10 kΩ or higher
G57-29 (ABFS) - G57-1 (AM22) Power switch off 10 kΩ or higher
G57-29 (ABFS) - G57-14 (SPDI) Power switch off 10 kΩ or higher
G57-29 (ABFS) - G58-1 (ACCD) Power switch off 10 kΩ or higher
G57-29 (ABFS) - G58-2 (IG1D) Power switch off 10 kΩ or higher
G57-29 (ABFS) - G58-7 (AM21) Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)


e.

Connect the airbag sensor assembly connector.


f.

Connect the power management control ECU connectors.


g.

Install the IGCT No. 2 fuse and AM2 fuse.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR