Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › from 2015.11
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277925 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0A9C-123  Hybrid Battery Temperature Sensor "A" Range / Performance  P0AC6-123  Hybrid Battery Temperature Sensor "B" Range / Performance  P0ACB-123  Hybrid Battery Temperature Sensor "C" Range / Performance  P3065-123  Hybrid Battery Temperature Sensor Range/Performance Stuck "A"  


DESCRIPTION

The battery temperature sensors are provided at 3 locations of the HV battery. The resistance of the thermistor, which is built into each battery temperature sensor, varies in accordance with changes in the HV battery temperature. The lower the battery temperature, the higher the thermistor resistance. Conversely, the higher the temperature, the lower the resistance. The battery smart unit uses the battery temperature sensors to detect the HV battery temperature, and sends the detected value to the hybrid vehicle control ECU. Based on the results of this detection, the hybrid vehicle control ECU controls the blower fan. (The blower fan starts when HV battery temperature rises above a predetermined level.)

Temperature Sensor Identification Cross Reference Table:
DTC Title Sensor Battery Temperature Sensor Intelligent tester Display
A 0 1
B 1 2
C 2 3


HINT:

For example, sensor A in the DTC title is battery temperature sensor (No. 0). This sensor is displayed as Temp of Batt TB1 in the Data List.


A171806E02
1.824,0.012 2.564,0.170 0.740,0.157 10 Reference: 2.171,0.354 2.431,0.503 0.260,0.149 10 250 2.171,0.673 2.431,0.822 0.260,0.149 10 200 2.171,0.981 2.431,1.129 0.260,0.149 10 150 2.173,1.276 2.433,1.425 0.260,0.149 10 100 2.25,1.579 2.433,1.728 0.184,0.149 10 50 2.331,1.901 2.434,2.050 0.104,0.149 10 0 3.273,2.255 3.376,2.404 0.104,0.149 10 0 2.577,2.252 2.804,2.421 0.227,0.169 10 -40 2.921,2.252 3.148,2.421 0.227,0.169 10 -20 3.522,2.252 3.696,2.421 0.174,0.169 10 20 3.815,2.252 3.989,2.421 0.174,0.169 10 40 4.094,2.252 4.268,2.421 0.174,0.169 10 60 4.401,2.252 4.576,2.421 0.174,0.169 10 80 4.644,2.252 4.901,2.421 0.257,0.169 10 100 3.176,2.457 3.443,2.606 0.268,0.149 10 (32) 2.53,2.451 2.862,2.620 0.332,0.169 10 (-40) 2.908,2.453 3.170,2.622 0.262,0.169 10 (-4) 3.46,2.453 3.727,2.622 0.267,0.169 10 (68) 3.709,2.453 4.075,2.622 0.366,0.169 10 (104) 4.028,2.453 4.372,2.622 0.344,0.169 10 (140) 4.352,2.453 4.702,2.622 0.350,0.169 10 (176) 4.676,2.453 5.021,2.622 0.346,0.169 10 (212) 5.096,2.242 5.370,2.440 0.274,0.198 10 (°C) 5.096,2.445 5.427,2.643 0.331,0.198 10 (°F) 1.82,0.379 2.115,0.577 0.295,0.198 10 (kΩ) 1.403,0.568 2.135,0.752 0.731,0.184 10 Resistance 5.462,2.235 6.800,2.423 1.339,0.188 10 Battery Temperature 2.6,0.008 5.691,0.187 3.091,0.179 10 Battery Temperature Sensor Characteristic Graph


DTC No. INF Code DTC Detection Condition Trouble Area
P0A9C
P0AC6
P0ACB
P3065
123 When the battery temperature sensor performance is abnormal (1 trip detection/2 trip detection)
·

Hybrid battery thermistor

·

Battery smart unit

·

Wire harness or connector



WIRING DIAGRAM

A244328E17
5.563,6.438 6.844,6.875 1.281,0.438 10 false Battery Smart Unit 5.625,6.021 6.01,6.208 0.385,0.188 10 false GND 5.635,2.354 6.083,2.583 0.448,0.229 10 false TCO 5.635,4.917 6.01,5.094 0.375,0.177 10 false TB2 5.635,4.073 5.99,4.26 0.354,0.188 10 false TB1 5.646,3.219 5.99,3.417 0.344,0.198 10 false TBO 5.635,2.844 6.042,3.083 0.406,0.24 10 false GCO 5.635,3.698 6.031,3.896 0.396,0.198 10 false GBO 5.625,5.417 5.969,5.573 0.344,0.156 10 false GB2 5.635,4.552 6.021,4.74 0.385,0.188 10 false GB1 5.292,2.448 5.521,2.625 0.229,0.177 10 false d1 5.281,2.917 5.51,3.094 0.229,0.177 10 false d1 5.292,3.313 5.521,3.49 0.229,0.177 10 false d1 5.292,3.781 5.521,3.958 0.229,0.177 10 false d1 5.292,4.156 5.521,4.333 0.229,0.177 10 false d1 5.281,4.635 5.51,4.813 0.229,0.177 10 false d1 5.281,5.021 5.51,5.198 0.229,0.177 10 false d1 5.281,5.5 5.51,5.677 0.229,0.177 10 false d1 5.333,5.823 5.51,5.969 0.177,0.146 10 false 6 5.323,3.135 5.51,3.292 0.188,0.156 10 false 4 5.333,3.979 5.531,4.135 0.198,0.156 10 false 3 5.323,2.74 5.583,2.896 0.26,0.156 10 false 7 5.313,5.333 5.604,5.479 0.292,0.146 10 false 8 5.323,4.833 5.573,5 0.25,0.167 10 false 2 5.292,3.604 5.552,3.75 0.26,0.146 10 false 10 5.323,4.448 5.583,4.594 0.26,0.146 10 false 9 2.365,2.656 4.323,3.156 1.958,0.5 10 false Inlet Air Temperature Sensor 2.354,3.51 4.438,3.865 2.083,0.354 10 false Battery Temperature Sensor 0 2.365,4.354 4.396,4.76 2.031,0.406 10 false Battery Temperature Sensor 1 2.365,5.208 4.531,5.563 2.167,0.354 10 false Battery Temperature Sensor 2 2.479,6 4.385,6.219 1.906,0.219 10 false Hybrid Battery Thermistor 0.708,5.667 1.938,5.927 1.229,0.26 10 false Auxiliary Battery 4.135,0.938 4.979,1.156 0.844,0.219 10 false IGCT No. 4 2.938,1.177 3.344,1.396 0.406,0.219 10 false MREL 2.125,1.594 2.417,1.75 0.292,0.156 10 false A72 5.24,0.792 5.625,1.031 0.385,0.24 10 false M39 5.615,0.792 6.094,1.01 0.479,0.219 10 false IGCT 1.802,0.698 2.052,0.875 0.25,0.177 10 false 5 1.073,0.698 1.323,0.927 0.25,0.229 10 false 3 1.073,1.073 1.323,1.292 0.25,0.219 10 false 2 1.802,1.063 2.052,1.24 0.25,0.177 10 false 1 0.563,2.313 1.396,2.573 0.833,0.26 10 false IGCT-MAIN 2.75,1.073 3,1.25 0.25,0.177 10 false 6 5.333,0.594 5.521,0.781 0.188,0.188 10 false 3 5.344,2.26 5.521,2.458 0.177,0.198 10 false 1 5.229,6.021 5.542,6.229 0.313,0.208 10 false M39 1.313,1.417 1.76,1.615 0.448,0.198 10 false IGCT 0.604,4.104 1.083,4.302 0.479,0.198 10 false MAIN 2.417,1.594 4.708,1.938 2.292,0.344 10 false Hybrid Vehicle Control ECU 4.604,0.625 4.885,0.823 0.281,0.198 10 false 2 4.198,0.635 4.448,0.813 0.25,0.177 10 false 1 0.344,2.094 0.604,2.281 0.26,0.188 10 false 2 0.333,2.49 0.583,2.667 0.25,0.177 10 false 1

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION).

HINT:

At least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)

A

2.CHECK INSTALLATION OF BATTERY TEMPERATURE SENSOR

B

2.CHECK INSTALLATION OF BATTERY TEMPERATURE SENSOR
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper hybrid battery cover sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).


c.

Visually check the installation condition of the relevant battery temperature sensor.

A467983E01
0.667,0.146 1.042,0.385 0.375,0.24 12 false *A 0.667,3.021 1.042,3.26 0.375,0.24 12 false *B 4.563,1.948 4.938,2.188 0.375,0.24 10 false *1 3.26,1.656 3.635,1.896 0.375,0.24 10 false *2 2.167,1.625 2.542,1.865 0.375,0.24 10 false *3 4.563,4.729 4.938,4.969 0.375,0.24 10 false *1 3.25,4.396 3.625,4.635 0.375,0.24 10 false *2 2.167,4.385 2.542,4.625 0.375,0.24 10 false *3

Text in Illustration
*A for 2 Clamps Type *B for 6 Clamps Type
*1 Battery Temperature Sensor 0 *2 Battery Temperature Sensor 1
*3 Battery Temperature Sensor 2 - -

Standard Condition:

Each battery temperature sensor is installed in the correct location with the correct orientation and its claws are engaged securely.


Result:
Result Proceed to
Each battery temperature sensor is installed in the correct location with the correct orientation and its claws are engaged securely. A
Claws are damaged. B
Any of battery temperature sensors are not installed correctly, but claws are not damaged. C


NOTICE:

Do not use a stick or similar object to push on the sensors when inspecting them. Doing so may result in damage to the sensors.



d.

Install the upper hybrid battery cover sub-assembly.



A

3.CHECK HYBRID BATTERY THERMISTOR (BATTERY TEMPERATURE SENSOR)

B

C

INSTALL PARTS CORRECTLY

3.CHECK HYBRID BATTERY THERMISTOR (BATTERY TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY SMART UNIT>REMOVAL).


c.

Disconnect connectors d1 and M39 from the battery smart unit.


d.
U158964E03
1.667,2.042 0.844,1.417 false 2.271,1.24 1.781,2.021 false 2.688,1.677 1.896,2.042 false 2.573,2.438 1.917,2.156 false 2.104,2.677 1.802,2.156 false 1.635,2.177 1.01,2.531 false 0.771,0.24 0.969,0.417 0.198,0.177 10 false *a 2.719,1.583 3.073,1.771 0.354,0.188 10 false TB2 2.292,1.104 2.646,1.292 0.354,0.188 10 false TB1 0.448,1.292 0.802,1.479 0.354,0.188 10 false TBO 0.594,2.5 0.948,2.688 0.354,0.188 10 false GBO 2.125,2.635 2.479,2.823 0.354,0.188 10 false GB1 2.604,2.354 2.958,2.542 0.354,0.188 10 false GB2 1.635,1.208 1.906,1.438 0.271,0.229 10 false d1

Measure the resistance of the circuit for the malfunctioning sensor (battery temperature sensor 0 to 2).

Tester Connection
Tester Connection Battery Temperature Sensor No.
d1-4 (TBO) - d1-10 (GBO) 0
d1-3 (TB1) - d1-9 (GB1) 1
d1-2 (TB2) - d1-8 (GB2) 2

Standard Resistance:
Thermistor Temperature Switch Condition Specified Condition
0°C (32°F) Power switch off 26.7 to 27.8 kΩ
25°C (77°F) Power switch off 9.9 to 10.1 kΩ
40°C (104°F) Power switch off 5.73 to 5.92 kΩ


Text in Illustration
*a Rear view of wire harness connector
(to Battery Smart Unit)


e.
U158906E03
1.563,2.313 1.135,2.25 false 2.042,4.365 1.896,4.115 false 2.531,3.563 1.896,3.979 false 2.396,3.313 1.792,3.979 false 1.083,3.958 1.646,3.979 false 1.156,4.313 1.646,4.135 false 1.365,4.396 1.771,4.135 false 2.521,3.885 2.021,4.021 false 2.542,4.167 2.021,4.135 false 1.563,2.448 1.135,2.583 false 0.177,0.125 0.448,0.302 0.271,0.177 10 false *a 0.802,2.167 1.198,2.406 0.396,0.24 10 false IGCT 0.781,3.896 1.125,4.104 0.344,0.208 10 false TBO 2.448,3.146 2.781,3.354 0.333,0.208 10 false TB1 2.594,3.458 3.01,3.708 0.417,0.25 10 false TB2 0.792,4.26 1.146,4.458 0.354,0.198 10 false GBO 1.167,4.417 1.5,4.604 0.333,0.188 10 false GB1 1.969,4.385 2.281,4.563 0.313,0.177 10 false GB2 2.583,3.792 2.958,3.979 0.375,0.188 10 false TCO 2.594,4.083 2.969,4.292 0.375,0.208 10 false GCO 0.885,1.677 1.396,1.958 0.51,0.281 10 false M39 0.667,3.469 0.958,3.688 0.292,0.219 10 false d1 0.813,2.531 1.208,2.771 0.396,0.24 10 false GND

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Standard Resistance
d1-4 (TBO) - M39-3 (IGCT) Power switch off 10 kΩ or more
d1-4 (TBO) - M39-6 (GND) Power switch off 10 kΩ or more
d1-10 (GBO) - M39-3 (IGCT) Power switch off 10 kΩ or more
d1-10 (GBO) - M39-6 (GND) Power switch off 10 kΩ or more
d1-3 (TB1) - M39-3 (IGCT) Power switch off 10 kΩ or more
d1-3 (TB1) - M39-6 (GND) Power switch off 10 kΩ or more
d1-9 (GB1) - M39-3 (IGCT) Power switch off 10 kΩ or more
d1-9 (GB1) - M39-6 (GND) Power switch off 10 kΩ or more
d1-2 (TB2) - M39-3 (IGCT) Power switch off 10 kΩ or more
d1-2 (TB2) - M39-6 (GND) Power switch off 10 kΩ or more
d1-8 (GB2) - M39-3 (IGCT) Power switch off 10 kΩ or more
d1-8 (GB2) - M39-6 (GND) Power switch off 10 kΩ or more
d1-1 (TCO) - M39-3 (IGCT) Power switch off 10 kΩ or more
d1-1 (TCO) - M39-6 (GND) Power switch off 10 kΩ or more
d1-7 (GCO) - M39-3 (IGCT) Power switch off 10 kΩ or more
d1-7 (GCO) - M39-6 (GND) Power switch off 10 kΩ or more


Text in Illustration
*a Rear view of wire harness connector
(to Battery Smart Unit)


f.

Connect the battery smart unit connectors.


g.

Install the No. 1 hybrid battery shield sub-assembly.



OK

NG

4.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR)
4.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper hybrid battery cover sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).


c.

Check the wire harness and connectors of the battery temperature sensor for abnormalities by sight and touch.

Specified Condition:

There are no open or short circuits in the wire harness and connectors. There are no short circuits to other wire harnesses.



d.

Install the upper hybrid battery cover sub-assembly.



OK

NG

REPAIR HARNESS OR CONNECTOR (BATTERY TEMPERATURE SENSOR)