Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › BATTERY SMART UNIT › 2014.12–2017.06
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277929 BATTERY SMART UNIT A

HYBRID / BATTERY CONTROL  BATTERY SMART UNIT  INSTALLATION  


PROCEDURE

Hide 89892A 1.INSTALL BATTERY SMART UNIT

CAUTION:

Wear insulated gloves.


a.

w/o Wiring Harness Protector:

i.
A266715E01
2.689,0.788 2.914,1.027 0.225,0.239 10 *a 2.506,0.863 2.686,0.863 false

Install the battery smart unit to the HV battery with the bolt.

Text in Illustration
*a Red Label

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

NOTICE:

Check color of the label.



ii.

Connect the battery smart unit connector.

NOTICE:

The connector should be connected securely.




b.

w/ Wiring Harness Protector:

i.
A311369E02
2.26,0.938 2.479,0.938 false 2.5,0.854 3,1.417 0.5,0.563 10 false *a

Install the battery smart unit to the HV battery with the bolt.

Text in Illustration
*a Red Label

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

NOTICE:

Check color of the label.



ii.

Install the wiring harness protector to the battery smart unit connector.


iii.

Connect the battery smart unit connector.

NOTICE:

The connector should be connected securely.



iv.

Engage the 2 claws to install the wiring harness protector cover to the battery smart unit connector.



Hide G920C 2.INSTALL NO. 2 HYBRID VEHICLE BATTERY CARRIER BRACKET SUB-ASSEMBLY

CAUTION:

Wear insulated gloves.


a.

Install the No. 2 hybrid vehicle battery carrier bracket sub-assembly with the bolt and 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Engage the 3 clamps.


c.

Connect the battery smart unit connector.

NOTICE:

The connector should be connected securely.



Hide G920Q 3.INSTALL NO. 1 HYBRID BATTERY SHIELD SUB-ASSEMBLY

CAUTION:

Wear insulated gloves.


a.

Install the No. 1 hybrid battery shield sub-assembly with the 2 bolts and 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.
A255172

Install the electric vehicle battery plug with the bolt as shown in the illustration.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide G92T9 4.INSTALL HYBRID BATTERY SERVICE PLUG COVER

CAUTION:

Wear insulated gloves.


a.

Install the hybrid battery service plug cover with the 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 5.CONNECT WIRE HARNESS

a.

Engage the clamp.


b.

Connect the 2 connectors.


Hide G92F1 6.INSTALL NO. 1 HYBRID BATTERY EXHAUST DUCT

a.

Install the No. 1 hybrid battery exhaust duct with the clip.


Hide 71033 7.INSTALL REAR SEAT CUSHION LEG SUB-ASSEMBLY

a.

Temporarily install the rear seat cushion leg sub-assembly with the 4 bolts.


b.
A266710E02
3.167,0.948 3.406,1.177 0.24,0.229 10 false C 0.26,0.75 0.396,0.979 0.135,0.229 10 false C 0.292,1.792 0.531,2.021 0.24,0.229 10 false A 2.365,0.073 2.542,0.26 0.177,0.188 10 true B

Tighten the bolt (A).

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.

Tighten the bolt (B).

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


d.

Tighten the 2 bolts (C).

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 8.INSTALL REAR SEAT CUSHION ASSEMBLY (for Separate Type Seatback)

Hide 9.INSTALL REAR SEAT CUSHION ASSEMBLY (for Bench Type Seatback)