Home › Engine / Hybrid System › 1NZ-FXE (ENGINE MECHANICAL) › CAMSHAFT › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057005 1NZ-FXE ENGINE MECHANICAL _0277944 CAMSHAFT A

1NZ-FXE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


PROCEDURE

Hide 25680 1.REMOVE EGR COOLER ASSEMBLY

Hide 47220D 2.SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (for RHD)

a.
A266931

Disconnect the connector.


b.

Remove the bolt and nut, and separate the brake master cylinder reservoir assembly.


Hide 82121 4.SEPARATE ENGINE WIRE (for LHD)

a.
A266930

Disconnect the 4 injector connectors.


b.
A268171

Disconnect the wire harness clamp.


c.

Remove the 3 bolts and separate the engine wire.


Hide 82121 5.SEPARATE ENGINE WIRE (for RHD)

a.
A266930

Disconnect the 4 injector connectors.


b.
A266929

Remove the 3 bolts and separate the engine wire.


Hide 11201 6.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A266933

Disconnect the No. 1 ventilation hose and No. 2 ventilation hose.


b.
A265764

Remove the 9 bolts, 2 seal washers, 2 nuts and cylinder head cover sub-assembly.


c.

Remove the gasket from the cylinder head cover sub-assembly.


Hide 13512 9.REMOVE NO. 2 CAMSHAFT

a.
A266923E01
0.51,0.215 0.665,0.376 0.155,0.162 10 *a 1.588,0.305 0.705,0.305 false

Loosen the bolts on the camshaft timing gear or sprocket while holding the hexagonal portion of the No. 2 camshaft.

Text in Illustration
*a Hold


b.
A266920E01
1.839,1.589 2.000,1.738 0.160,0.150 10 *1 2.685,2.91 2.846,3.059 0.160,0.150 10 *a 1.324,2.951 1.484,3.100 0.160,0.150 10 *2 1.388,1.983 1.7,1.67 1.7,1.67 1.83,1.67 false 1.165,2.691 1.165,3.035 1.165,3.035 1.31,3.035 false

Insert a screwdriver from the plug hole and turn the stopper plate of the No. 1 chain tensioner assembly clockwise to release the lock, and keep it as it is.

Text in Illustration
*1 Plunger
*2 Stopper Plate
*a Unlock

HINT:
·

The plunger of the No. 1 chain tensioner assembly is locked.

·

If the stopper plate is locked firmly, slightly turn the hexagonal portion of the camshaft to the right and left.




c.
A266924E01
2.83,2.145 2.993,2.304 0.163,0.158 10 *1 2.681,2.457 2.681,2.231 2.681,2.231 2.819,2.231 false

Slightly turn the hexagonal portion of the No. 2 camshaft clockwise so that the plunger of the No. 1 chain tensioner assembly is pushed by the chain sub-assembly.

Text in Illustration
*1 Plunger


d.
A380684E01
1.448,2.208 1.656,1.979 1.656,1.979 1.896,1.979 false 1.323,3.104 1.323,2.833 false 1.26,3.125 1.573,3.323 0.313,0.198 10 false *3 1.927,1.896 2.24,2.094 0.313,0.198 10 false *2 2.708,3.073 3.021,3.271 0.313,0.198 10 false *a

A380685E01
2.688,1.104 2.958,1.104 false 2.99,1.021 3.302,1.219 0.313,0.198 10 false *1

Insert a screwdriver from the plug hole and turn the stopper plate of the No. 1 chain tensioner assembly counterclockwise to the lock, and keep it as it is. Insert the hexagon wrench into the stopper plate hole.

Text in Illustration
*1 Hexagon Wrench
*2 Plunger
*3 Stopper Plate
*a Lock

HINT:

Hold the hexagon wrench with tape so that the hexagon wrench does not come off.



e.
U159032E04
0.979,1.781 1.104,1.927 0.125,0.146 10 false 1 2.344,0.156 2.604,0.354 0.26,0.198 10 false 2 1.24,0.156 1.5,0.375 0.26,0.219 10 false 5 0.677,0.156 0.969,0.385 0.292,0.229 10 false 3 1.792,0.156 2.167,0.427 0.375,0.271 10 false 4

Using several steps, uniformly loosen and remove the 11 bolts in the sequence shown in the illustration. Then remove the No. 1 camshaft bearing cap and 4 No. 2 camshaft bearing caps.

NOTICE:

Uniformly loosen the bolts while keeping the No. 2 camshaft level.



f.
A037148

Remove the bolt with the No. 2 camshaft lifted up.


g.

Remove the No. 2 camshaft and camshaft timing gear or sprocket.


Hide 13511 10.REMOVE CAMSHAFT

a.
A266926E01
0.827,0.136 0.996,0.298 0.168,0.162 10 *a 2.055,0.927 1.357,0.229 1.357,0.229 1.029,0.229 false

Loosen the bolts on the camshaft timing gear assembly while holding the hexagonal portion of the camshaft.

Text in Illustration
*a Hold


b.
U159031E03
1.031,1.781 1.156,1.927 0.125,0.146 10 false 2 1.583,1.781 1.708,1.927 0.125,0.146 10 false 4 2.135,1.781 2.26,1.927 0.125,0.146 10 false 3 2.667,1.781 2.792,1.927 0.125,0.146 10 false 1

Using several steps, uniformly loosen and remove the 8 bolts in the sequence shown in the illustration. Then remove the 4 No. 2 camshaft bearing caps.

NOTICE:

Uniformly loosen the bolts while keeping the camshaft level.



c.
A035767

Hold the chain sub-assembly with one hand, and remove the camshaft.


d.
A266927

Tie the chain sub-assembly with a string or similar as shown in the illustration.

NOTICE:

Be careful not to drop anything inside the timing chain cover.



Hide 13050 11.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

a.

Check the camshaft timing gear assembly lock.

i.
A267919

Clamp the camshaft in a vise, and make sure that the camshaft timing gear assembly does not rotate.



b.

Release the lock pin.

i.
A266804E01
2.319,0.337 2.478,0.494 0.159,0.157 10 *a 0.685,1.778 0.845,1.935 0.159,0.157 10 *b 2.613,3.173 2.772,3.330 0.159,0.157 10 *c 2.622,3.446 2.781,3.603 0.159,0.157 10 *d 0.588,3.56 0.747,3.717 0.159,0.157 10 *c 0.567,3.124 0.726,3.281 0.159,0.157 10 *d 1.665,0.945 2.069,0.422 2.069,0.422 2.295,0.422 false 1.568,1.336 1.175,1.865 1.175,1.865 0.883,1.865 false 1.317,3.204 0.762,3.204 false 1.279,3.338 0.968,3.648 0.968,3.648 0.779,3.648 false 2.12,2.974 2.406,3.26 2.406,3.26 2.596,3.26 false 2.059,3.538 2.603,3.538 false

Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

Text in Illustration
*a Retard Side Path
*b Advance Side Path
*c Open
*d Close
V100144

Rubber Piece
V100145

Vinyl Tape

HINT:

4 oil paths are provided in the groove. Plug 2 paths with rubber pieces.



ii.

Prick a hole in the tape placed on the advance side path. Prick a hole in the tape placed on the retard side path, on the opposite side to that of the advance side path, as shown in the illustration.


iii.
A146376E01
0.711,0.281 0.873,0.428 0.163,0.147 10 *a 2.751,0.379 2.913,0.526 0.163,0.147 10 *b 1.63,0.904 1.198,0.361 1.198,0.361 0.903,0.361 false 1.911,0.996 2.446,0.461 2.446,0.461 2.73,0.461 false

Apply approximately 150 kPa (1.5 kgf/cm2, 22 psi) of air pressure to the 2 paths (the advance side path and the retard side path).

Text in Illustration
*a Advance Side Path
*b Retard Side Path

HINT:

Cover the paths with a piece of cloth when applying pressure to keep oil from splashing.



iv.
A146374E01
0.635,0.709 0.816,0.860 0.180,0.151 10 *a 0.521,2.371 0.701,2.522 0.180,0.151 10 *c 2.675,0.791 2.855,0.942 0.180,0.151 10 *b 2.764,2.475 2.944,2.625 0.180,0.151 10 *d 1.589,1.419 1.082,0.791 1.082,0.791 0.84,0.791 false 1.888,1.515 2.368,0.872 2.368,0.872 2.656,0.872 false

Make sure that the camshaft timing sprocket turns in the retard direction when reducing the air pressure applied to the advance side path.

Text in Illustration
*a Advance Side Path
*b Retard Side Path
*c Decompress
*d Hold Pressure

HINT:

The lock pin is released and the camshaft timing sprocket turns in the retard direction.



v.

When the camshaft timing sprocket moves to the most retarded position, release the air pressure from the advance side path, and then release the air pressure from the retard side path.

NOTICE:

Be sure to release the air pressure from the advance side path first. If the air pressure of the retard side path is released first, the camshaft timing sprocket may abruptly shift in the advance direction and break the lock pin or other parts.




Hide 13050 12.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A032639E07
1.167,1.583 1.167,1.823 1.167,1.823 1.583,1.823 false 1.354,1.396 1.354,1.823 false 1.083,0.854 1.083,0.625 1.083,0.625 0.677,0.625 false 0.948,1.083 0.948,0.625 false 1.583,1.74 1.76,1.896 0.177,0.156 10 false *a 0.479,0.531 0.656,0.688 0.177,0.156 10 false *a

Remove the bolt and camshaft timing gear assembly.

Text in Illustration
*a Do Not Remove

NOTICE:
·

Be sure not to remove the other 4 bolts.

·

When reusing the camshaft timing gear assembly, release the lock pin first, then install the camshaft timing gear assembly.