Home › Engine / Hybrid System › 1NZ-FXE (ENGINE MECHANICAL) › CYLINDER HEAD
RM2170E _51 Engine / Hybrid System _057005 1NZ-FXE ENGINE MECHANICAL _0277950 CYLINDER HEAD G

1NZ-FXE ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 11101 1.INSPECT CYLINDER HEAD FOR FLATNESS

a.
A380675

A380676E01
0.271,0.438 0.583,0.635 0.313,0.198 10 false *a 0.25,2.177 0.563,2.375 0.313,0.198 10 false *b 0.24,3.323 0.552,3.521 0.313,0.198 10 false *c

Using a precision straightedge and feeler gauge, measure the warpage of the contact surfaces where the cylinder head sub-assembly contacts the cylinder block and manifold.

Text in Illustration
*a Cylinder Block Side
*b Intake Manifold Side
*c Exhaust Manifold Side

Maximum warpage:
Surface Specified Condition
Cylinder block side 0.05 mm (0.00197 in.)
Intake manifold side 0.10 mm (0.00394 in.)
Exhaust manifold side 0.10 mm (0.00394 in.)


If the warpage is greater than the maximum, replace the cylinder head sub-assembly.


Hide 11101 2.INSPECT CYLINDER HEAD FOR CRACKS

a.
A088721

Using a dye penetrant, check the intake ports, exhaust ports and cylinder head sub-assembly surface for cracks.

If cracked, replace the cylinder head sub-assembly.


Hide 13711 3.INSPECT INTAKE VALVE

a.
A121380E09
1.884,0.993 2.059,1.166 0.175,0.173 10 *a

Using a vernier caliper, measure the overall length of the intake valve.

Text in Illustration
*a Overall Length

Standard overall length:

89.25 mm (3.51 in.)


Minimum overall length:

88.95 mm (3.50 in.)


If the overall length is less than the minimum, replace the intake valve.


b.
A121378

Using a micrometer, measure the diameter of the valve stem.

Standard valve stem diameter:

4.970 to 4.985 mm (0.19567 to 0.19626 in.)


If the valve stem diameter is not as specified, check the oil clearance.


c.
A194996E11
0.552,1.594 0.771,1.76 0.219,0.167 10 false *a

Using a vernier caliper, measure the valve head margin thickness.

Text in Illustration
*a Margin Thickness

Standard margin thickness:

1.0 mm (0.0394 in.)


Minimum margin thickness:

0.7 mm (0.0276 in.)


If the margin thickness is less than the minimum, replace the intake valve.


Hide 13715 4.INSPECT EXHAUST VALVE

a.
A121383E09
1.932,0.968 2.106,1.133 0.174,0.165 10 *a

Using a vernier caliper, measure the overall length of the exhaust valve.

Text in Illustration
*a Overall Length

Standard overall length:

87.90 mm (3.46 in.)


Minimum overall length:

87.60 mm (3.45 in.)


If the overall length is less than the minimum, replace the exhaust valve.


b.
A121381

Using a micrometer, measure the diameter of the valve stem.

Standard valve stem diameter:

4.965 to 4.980 mm (0.19547 to 0.19606 in.)


If the valve stem diameter is not as specified, check the oil clearance.


c.
A121382E13
0.613,1.323 0.769,1.492 0.156,0.169 10 *a

Using a vernier caliper, measure the valve head margin thickness.

Text in Illustration
*a Margin Thickness

Standard margin thickness:

1.15 mm (0.0453 in.)


Minimum margin thickness:

0.85 mm (0.0335 in.)


If the margin thickness is less than the minimum, replace the exhaust valve.


Hide 5.INSPECT COMPRESSION SPRING

a.
A194990

Using a vernier caliper, measure the free length of the compression spring.

Standard free length:

59.77 mm (2.35 in.)



b.
A194991E06
2.466,0.137 2.625,0.288 0.159,0.150 10 *a 0.963,0.907 1.127,1.073 0.164,0.165 10 *1 1.72,1 1.152,1 false

Using a steel square, measure the deviation of the compression spring.

Text in Illustration
*1 Steel Square
*a Deviation

Maximum deviation:

1.6 mm (0.0630 in.)



Hide 6.INSPECT VALVE GUIDE BUSH OIL CLEARANCE

a.
A088733

Using a caliper gauge, measure the inside diameter of the valve guide bush.

Bush inside diameter:

5.01 to 5.03 mm (0.197 to 0.198 in.)



b.

Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.

Standard oil clearance:
Valve Guide Bush Specified Condition
Intake 0.025 to 0.060 mm (0.000984 to 0.00236 in.)
Exhaust 0.030 to 0.065 mm (0.00118 to 0.00256 in.)


Maximum oil clearance:
Guide Bush Specified Condition
Intake 0.08 mm (0.00315 in.)
Exhaust 0.10 mm (0.00394 in.)


If the oil clearance is greater than the maximum, replace the valve and valve guide bush (see page Engine / Hybrid System>1NZ-FXE (ENGINE MECHANICAL)>CYLINDER HEAD>REPLACEMENT).


Hide 7.INSPECT VALVE SEATS

a.

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the valve seat.


c.
A194998E10
1.708,1.708 1.896,1.875 0.188,0.167 10 false *a

Check the valve face and seat according to the following procedure.

Text in Illustration
*a Width

i.

If Prussian blue appears 360° around the valve face, the valve face is concentric. If not, replace the valve.


ii.

If Prussian blue appears 360° around the valve seat, the guide and valve face are concentric. If not, resurface the valve seat.


iii.

Check that the valve seat contact is in the middle of the valve face with the valve seat width between 1.0 and 1.4 mm (0.0394 to 0.0551 in.).



Hide 13751 8.INSPECT VALVE LIFTER

a.
P016860

Using a micrometer, measure the valve lifter diameter.

Standard lifter diameter:

30.966 to 30.976 mm (1.2191 to 1.2195 in.)



Hide 13751 9.INSPECT VALVE LIFTER OIL CLEARANCE

a.
A088724

Using a caliper gauge, measure the valve lifter bore diameter of the cylinder head sub-assembly.

Standard lifter bore diameter:

31.009 to 31.025 mm (1.2208 to 1.2215 in.)



b.

Subtract the lifter diameter measurement from the lifter bore diameter measurement.

Standard oil clearance:

0.033 to 0.059 mm (0.00130 to 0.00232 in.)


Maximum oil clearance:

0.1 mm (0.00394 in.)


If the oil clearance is greater than the maximum, replace the valve lifter. If necessary, replace the cylinder head sub-assembly.


Hide 13511 10.INSPECT CAMSHAFT

a.

Inspect the camshaft for runout.

i.

Place the camshaft on V-blocks.


ii.
A088725

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.03 mm (0.00118 in.)


If the circle runout is greater than the maximum, replace the camshaft.



b.

Inspect the cam lobes.

i.
A037113

Using a micrometer, measure the cam lobe height.

Standard cam lobe height:

42.261 to 42.461 mm (1.6638 to 1.6717 in.)


Minimum cam lobe height:

42.16 mm (1.6598 in.)


If the cam lobe height is less than the minimum, replace the camshaft.



c.

Inspect the camshaft journals.

i.
A037114

Using a micrometer, measure the journal diameter.

Standard journal diameter:
Journal Specified Condition
No. 1 journal 34.449 to 34.465 mm (1.3563 to 1.3569 in.)
Other journals 22.949 to 22.965 mm (0.90350 to 0.90413 in.)


If the journal diameter is not as specified, check the oil clearance.



Hide 13512 11.INSPECT NO. 2 CAMSHAFT

a.

Inspect the camshaft for runout.

i.

Place the camshaft on V-blocks.


ii.
A088725

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.03 mm (0.00118 in.)


If the circle runout is greater than the maximum, replace the No. 2 camshaft.



b.

Inspect the cam lobes.

i.
A037113

Using a micrometer, measure the cam lobe height.

Standard cam lobe height:

44.046 to 44.146 (1.7341 to 1.7380 in.)


Minimum cam lobe height:

43.90 mm (1.7283 in.)


If the cam lobe height is less than the minimum, replace the No. 2 camshaft.



c.

Inspect the camshaft journals.

i.
A037114

Using a micrometer, measure the journal diameter.

Standard journal diameter:
Journal Specified Condition
No. 1 journal 34.449 to 34.465 mm (1.3563 to 1.3569 in.)
Other journals 22.949 to 22.965 mm (0.90350 to 0.90413 in.)


If the journal diameter is not as specified, check the oil clearance.



Hide 12.INSPECT CAMSHAFT THRUST CLEARANCE


b.
A088726

Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard thrust clearance:

0.040 to 0.095 mm (0.00157 to 0.00374 in.)


Maximum thrust clearance:

0.11 mm (0.00433 in.)


If the thrust clearance is greater than the maximum, replace the camshaft. If necessary, replace the camshaft bearing caps and the cylinder head sub-assembly.


Hide 13.INSPECT CAMSHAFT OIL CLEARANCE

NOTICE:

Do not turn the camshafts.


a.

Clean the camshaft bearing caps and the camshaft journals.


b.

Place the camshafts on the cylinder head sub-assembly.


c.
A088727E05
1.271,1.406 1.844,1.781 true 1.865,1.708 2.042,1.865 0.177,0.156 10 true *1

Lay a strip of Plastigage across each of the camshaft journals.

Text in Illustration
*1 Plastigage




f.
A088728E04
1.313,1.396 1.635,1.719 1.635,1.719 1.813,1.719 true 1.823,1.635 1.979,1.792 0.156,0.156 10 true *1

Measure the Plastigage at its widest point.

Text in Illustration
*1 Plastigage

Standard oil clearance:

0.035 to 0.072 mm (0.00138 to 0.00283 in.)


Maximum oil clearance:

0.115 mm (0.00453 in.)


If the oil clearance is greater than the maximum, replace the camshaft. If necessary, replace the camshaft bearing caps and the cylinder head sub-assembly.

NOTICE:

Completely remove the Plastigage.