Home › Engine / Hybrid System › 1NZ-FXE (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › 2011.12–2017.06
RM2170E _51 Engine / Hybrid System _057005 1NZ-FXE ENGINE MECHANICAL _0277945 CYLINDER HEAD GASKET A

1NZ-FXE ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the cylinder head sub-assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).


PROCEDURE

Hide 11115 2.INSTALL CYLINDER HEAD GASKET

a.
A265783E01
0.164,0.673 0.322,0.831 0.158,0.158 10 *a 1.589,0.066 1.746,0.224 0.158,0.158 10 *1 0.164,1.401 0.322,1.559 0.158,0.158 10 *a 0.652,0.419 0.534,0.762 0.534,0.762 0.349,0.762 false 0.652,1.827 0.534,1.485 0.534,1.485 0.349,1.485 false 1.032,0.508 1.388,0.152 1.388,0.152 1.573,0.152 false 3.064,0.473 3.221,0.631 0.158,0.158 10 *1 2.78,1.068 2.938,1.226 0.158,0.158 10 *b 2.603,0.819 2.862,0.559 2.862,0.559 3.047,0.559 false

Apply seal packing to a new cylinder head gasket as shown in the illustration.

Text in Illustration
*1 Cylinder Head Gasket
*a Apply Seal Packing To The Inner Corners
*b 4.5 to 5.5 mm (0.177 to 0.217 in.)
V100145

Seal Packing Black

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:

Install the cylinder head sub-assembly within 3 minutes and tighten the cylinder head bolts within 15 minutes after applying seal packing.



b.
A267001E01
0.733,0.197 0.892,0.352 0.159,0.155 10 *a

Place the cylinder head gasket on the cylinder block with the Lot No. facing upward.

Text in Illustration
*a Lot Number

NOTICE:
·

Remove any oil from the contact surface.

·

Be careful of the installation direction.




Hide 11101 3.INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
·

Perform "Inspection After Repairs" after replacing the cylinder head sub-assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).

·

The cylinder head bolts are tightened in 2 progressive steps.



a.

Place the cylinder head sub-assembly on the cylinder block.

NOTICE:
·

Ensure that no oil is on the mounting surface of the cylinder head sub-assembly.

·

Place the cylinder head sub-assembly gently in order not to damage the cylinder head gasket.




b.

Apply a light coat of engine oil to the threads and under the heads of the 10 cylinder head bolts.

NOTICE:

Ensure that no engine oil drips from any of the cylinder head bolts.



c.

Step 1:

i.
U159034E03
0.354,0.125 0.479,0.271 0.125,0.146 10 false 8 1.406,1.698 1.563,1.854 0.156,0.156 10 false 1 0.885,1.698 1.01,1.844 0.125,0.146 10 false 6 0.302,1.698 0.479,1.844 0.177,0.146 10 false 10 1.958,1.698 2.104,1.854 0.146,0.156 10 false 3 2.479,1.698 2.604,1.844 0.125,0.146 10 false 7 0.875,0.125 1,0.271 0.125,0.146 10 false 4 1.417,0.125 1.542,0.271 0.125,0.146 10 false 2 1.948,0.125 2.073,0.271 0.125,0.146 10 false 5 2.479,0.125 2.604,0.271 0.125,0.146 10 false 9

Using several steps, uniformly install and tighten the 10 cylinder head bolts and 10 washers with an 8 mm bi-hexagon wrench in the order shown in the illustration.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)



d.

Step 2:

i.
A268868E01
1.123,0.398 1.351,0.554 0.227,0.156 10 90° 1.109,1.608 1.271,1.765 0.162,0.156 10 *a 2.647,0.398 2.874,0.554 0.227,0.156 10 90° 1.656,1.117 1.508,1.697 1.508,1.697 1.304,1.697 false

Mark each cylinder head bolt head with paint as shown in the illustration.

Text in Illustration
*a Paint Mark
V100135

Engine Front


ii.

Further tighten the cylinder head bolts 90°, and then an additional 90° as shown in the illustration.



e.

Check that the paint mark is now at a 180° angle to the front.


f.

After tightening the cylinder head bolts, wipe off the seal packing material that seeped out from the contact surface between the cylinder head sub-assembly and cylinder block.


Hide 4.INSTALL CAMSHAFT

a.

Apply a light coat of engine oil to the camshaft and cylinder head sub-assembly journals.


b.
A268218E01
1.574,0.748 1.723,0.892 0.150,0.144 10 *b 1.649,1.574 1.798,1.718 0.150,0.144 10 *c 2.245,1.683 2.395,1.827 0.150,0.144 10 *a 0.99,0.828 1.568,0.828 false 0.476,1.405 0.476,1.657 0.476,1.657 1.636,1.657 false 1.458,1.333 1.458,1.657 false 2.545,0.819 2.327,0.819 2.327,0.819 2.327,1.681 false 2.52,1.304 2.327,1.304 false

Place the camshaft and No. 2 camshaft on the cylinder head sub-assembly with the timing mark on the camshaft timing gear assembly and camshaft timing sprocket facing upward.

Text in Illustration
*a Timing Mark
*b Timing Mark (Rectangle)
*c Mark (Circle)

HINT:

There are 3 marks on the camshaft timing sprocket. Make sure that the timing mark (rectangle) is at the top.



c.
U159094E03
0.385,0.667 0.583,0.667 0.583,0.667 0.833,1.198 false 1.219,1.5 1.219,1.563 1.219,1.563 3.104,1.563 true 1.729,1.5 1.729,1.563 false 2.229,1.5 2.229,1.563 false 2.729,1.49 2.729,1.552 false 1.219,1.833 1.219,1.771 1.219,1.771 3.104,1.771 true 1.719,1.833 1.719,1.771 false 2.229,1.833 2.229,1.771 false 2.719,1.833 2.719,1.771 false 1.667,0.51 1.792,0.656 0.125,0.146 10 false 1 0.396,2.25 0.521,2.396 0.125,0.146 10 false 5 2.188,0.521 2.313,0.667 0.125,0.146 10 false 2 1.156,0.51 1.281,0.656 0.125,0.146 10 false 3 2.698,0.51 2.823,0.656 0.125,0.146 10 false 4 1.677,2.688 1.802,2.833 0.125,0.146 10 false 1 2.188,2.677 2.313,2.823 0.125,0.146 10 false 2 1.167,2.677 1.292,2.823 0.125,0.146 10 false 3 2.708,2.677 2.833,2.823 0.125,0.146 10 false 4 0.208,0.583 0.365,0.729 0.156,0.146 10 false *1 3.104,1.479 3.26,1.625 0.156,0.146 10 true *2 3.104,1.688 3.26,1.833 0.156,0.146 10 true *2

Check the front marks and numbers on the No. 1 camshaft bearing cap and 8 No. 2 camshaft bearing caps, then temporarily install them with the 19 bolts.

Text in Illustration
*1 No. 1 Camshaft Bearing Cap
*2 No. 2 Camshaft Bearing Cap


d.

Uniformly tighten the 19 bolts in the sequence shown in the illustration.

Torque:
No. 2 camshaft bearing cap : 13 N*m (129 kgf*cm, 9 ft.*lbf)
No. 1 camshaft bearing cap : 23 N*m (234 kgf*cm, 17 ft.*lbf)

NOTICE:

Uniformly tighten the bolts while keeping the camshaft level.



Hide 13506 5.INSTALL CHAIN SUB-ASSEMBLY

a.
A265768E03
1.625,1.365 0.833,1.365 true 0.635,1.26 0.833,1.479 0.198,0.219 10 true *a 1.927,1.865 2.281,2.021 0.354,0.156 10 false 10.3°

Set the crankshaft in the position shown in the illustration.

Text in Illustration
*a Timing Mark

HINT:

The crankshaft will be set to 90° ATDC and the timing mark will be at the location shown in the illustration.



b.
A265769E03
1.063,0.823 1.5,0.823 true 0.458,1.323 0.458,1.646 0.458,1.646 1.583,1.646 true 1.427,1.406 1.427,1.646 true 2.583,1.313 3.073,1.313 true 2.625,0.792 3.083,0.49 true 1.219,0.073 1.448,0.219 0.229,0.146 10 false 10° 1.51,0.75 1.677,0.896 0.167,0.146 10 false *b 3.104,0.396 3.271,0.542 0.167,0.146 10 false *a 3.094,1.229 3.281,1.406 0.188,0.177 10 true *a 1.594,1.563 1.76,1.708 0.167,0.146 10 false *c 2.854,0.073 3.083,0.219 0.229,0.146 10 false 10°

Set the camshaft timing gear assembly and camshaft timing sprocket in the positions shown in the illustration.

Text in Illustration
*a Timing Mark
*b Timing Mark (Rectangle)
*c Mark (Circle)

HINT:

There are 3 marks on the camshaft timing sprocket. Make sure to set the timing mark (rectangle) to 10° as shown in the illustration. Make sure to set the camshaft timing gear assembly to 10° as shown in the illustration. This is the location of the camshafts when the crankshaft is 20° ATDC.



c.
A265770E03
1.938,1.25 1.938,1.906 true 1.854,1.906 2.01,2.063 0.156,0.156 10 false *a 2.573,1.25 2.938,1.406 0.365,0.156 10 true 30.3°

Set the crankshaft in the position shown in the illustration.

Text in Illustration
*a Timing Mark

HINT:

The crankshaft will be set to 20° ATDC and the timing mark will be at the location shown in the illustration.



d.

Install the No. 1 chain vibration damper with the 2 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


e.
A265771E03
2.031,2.865 2.5,2.865 true 1.583,1.146 1.583,1.469 1.583,1.469 0.365,1.469 true 0.51,1.01 0.51,1.469 true 1.135,0.448 0.458,0.448 true 2.448,0.74 3.135,0.74 true 1.177,0.302 1.177,0.146 1.177,0.146 2.677,0.146 false 2.521,0.313 2.521,0.146 false 1.927,2.781 2.333,2.219 true 2.688,0.042 2.844,0.188 0.156,0.146 10 false *d 3.156,0.656 3.313,0.802 0.156,0.146 10 false *a 2.375,2.125 2.531,2.271 0.156,0.146 10 false *a 2.521,2.781 2.677,2.927 0.156,0.146 10 false *e 0.292,0.365 0.448,0.51 0.156,0.146 10 false *b 0.188,1.385 0.344,1.531 0.156,0.146 10 false *c

Align the timing marks of the camshaft and crankshaft with the mark plates of the timing chain sub-assembly and install the timing chain sub-assembly.

Text in Illustration
*a Timing Mark
*b Timing Mark (Rectangle)
*c Mark (Circle)
*d Orange Mark Plate
*e Yellow Mark Plate

HINT:
·

To prevent the No. 2 camshaft from springing back, turn it using a wrench and set it at the mark on the chain.

·

There are 3 marks on the camshaft timing sprocket. Make sure to align the mark plate with the timing mark (rectangle).




f.

Install the chain tensioner slipper.


g.

Install the No. 1 chain tensioner assembly with the 2 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


h.

Remove the hexagon wrench from the No. 1 chain tensioner assembly.


i.
A267436E03
1.052,0.438 0.375,0.438 true 1.01,0.292 1.01,0.135 1.01,0.135 2.667,0.135 false 2.333,0.292 2.333,0.135 false 2.396,0.74 3.094,0.74 true 1.604,1.052 1.604,1.469 1.604,1.469 0.354,1.469 true 0.51,1.104 0.51,1.469 true 2.354,3.156 2.052,2.802 true 1.948,2.698 2.198,2.042 true 0.198,0.354 0.344,0.51 0.146,0.156 10 false *b 0.177,1.385 0.323,1.542 0.146,0.156 10 false *c 2.688,0.052 2.833,0.208 0.146,0.156 10 false *d 3.115,0.646 3.26,0.802 0.146,0.156 10 false *a 2.229,1.938 2.375,2.094 0.146,0.156 10 false *a 2.635,2.677 2.99,2.833 0.354,0.156 10 false 10.3° 2.385,3.115 2.531,3.271 0.146,0.156 10 false *e

Turn the crankshaft approximately 20° counterclockwise to set it to TDC. Make sure that the timing marks and mark plates are correctly positioned.

Text in Illustration
*a Timing Mark
*b Timing Mark (Rectangle)
*c Mark (Circle)
*d Orange Mark Plate
*e Yellow Mark Plate

HINT:

There are 3 marks on the camshaft timing sprocket. Make sure that the timing mark (rectangle) is at the top.



Hide 17167 8.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 15100 11.INSTALL TIMING CHAIN COVER