Home › Drivetrain › P510 (HYBRID TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE › 2011.12–2017.06
RM2170E _52 Drivetrain _057013 P510 HYBRID TRANSMISSION / TRANSAXLE _0277994 TRANSMISSION CONTROL CABLE A

P510 HYBRID TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  INSTALLATION  


PROCEDURE

Hide 33829K 1.INSTALL NO. 2 TRANSMISSION CONTROL CABLE CLAMP

HINT:

Perform this procedure only when replacement of the No. 2 transmission control clamp is necessary.


a.
C251103E02
0.427,0.906 1.573,0.5 false 1.708,0.635 1.271,0.844 false 1.781,0.865 1.906,1.01 false 1.094,0.771 1.26,0.938 0.167,0.167 10 false *a 0.24,0.833 0.406,1 0.167,0.167 10 false *1 1.885,1.01 2.052,1.177 0.167,0.167 10 false *b

Install the No. 2 transmission control clamp to the body with the nut.

Text in Illustration
*1 Dash Silencer
*a Pushing Against The Dash Silencer
*b Arrow

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

NOTICE:
·

Install the No. 2 transmission control clamp so that its arrow mark points to the front of the vehicle.

·

Make sure that the transmission control cable support stopper is pushing against the dash silencer.




Hide 33820B 2.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Pass the transmission control cable into the vehicle and install the transmission control cable assembly to the body using the 3 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Install the transmission control cable assembly to the transmission control cable clamp and transmission control cable support.


c.

Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.


d.
C250073E02
3.004,0.797 3.169,0.962 0.165,0.165 10 *a 2.654,0.098 2.819,0.263 0.165,0.165 10 *b

Rotate the control shaft lever clockwise until it stops, and then from that position rotate it counterclockwise by 2 notches to set it to the N position.

Text in Illustration
*a P Position
*b N Position


e.

Install the transmission control cable assembly onto the transmission control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


f.
C195134E04
0.526,1.814 0.703,1.977 0.177,0.163 10 *1 2.894,0.51 3.071,0.673 0.177,0.163 10 *2 0.724,1.909 1.242,1.59 false 2.881,0.614 2.221,0.859 false 1.371,0.344 1.547,0.507 0.177,0.163 10 *a 2.15,0.023 2.326,0.186 0.177,0.163 10 *b

Rotate the nut of the transmission control cable assembly approximately 180° in the direction shown in the illustration, and while holding the nut, push in the lock.

Text in Illustration
*1 Nut
*2 Lock
*a Rotate Approximately 180°
*b Push In


g.
C250999E01
0.278,2.267 0.428,2.437 0.149,0.170 10 A 1.202,2.267 1.351,2.437 0.149,0.170 10 A 0.7,2.031 0.870,2.202 0.170,0.170 10 *b 2.433,2.009 2.603,2.180 0.170,0.170 10 *2 2.007,0.097 2.178,0.268 0.170,0.170 10 *1 1.032,0 1.203,0.170 0.170,0.170 10 *a 2.623,2.09 2.695,2.09 2.695,2.09 2.767,2.309 false 1.997,0.19 1.863,0.19 1.863,0.19 1.529,0.657 false

Install the transmission control cable assembly to the shift lever plate.

Text in Illustration
*1 Shift Lever Plate
*2 Lock
*a Install
*b Projecting Part

NOTICE:
·

Install the cable outer with the projecting part facing upwards.

·

After installation, make sure that the cable outer lock is projecting from A as shown in the illustration.

·

Make sure that the transmission control cable assembly are securely locked.




h.
C249909

Confirm that the shift lever is in N, and then install the cable end to the shift lever assembly.

NOTICE:
·

Securely install the cable end to the shift lever assembly.

·

Install the cable end so that its adjustment lock section is on the driver side.




Hide 58041A 4.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR SUB-ASSEMBLY

a.

Install the No. 1 floor heat insulator sub-assembly with the 2 bolts and nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 6.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 8.INSPECT FOR EXHAUST GAS LEAK