Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2015.11
RM2170E _53 Suspension _057019 TIRE PRESSURE MONITORING _0278018 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  B1247  Tire Pressure Monitor Receiver Communication Stop  


DESCRIPTION

The main body ECU (multiplex network body ECU) and tire pressure warning ECU and receiver are connected using 2 direct lines that they use to communicate with each other.

DTC No. DTC Detection Condition Trouble Area
B1247 In diagnostic mode, an applicable RDA signal cannot be received within 10 seconds after a PRG signal is sent from the main body ECU (multiplex network body ECU).
·

Tire pressure warning ECU and receiver

·

Wire harness or connector

·

Main body ECU (multiplex network body ECU)



WIRING DIAGRAM

C277674E10
0.156,2.906 1.896,3.26 1.74,0.354 10 false Tire Pressure Warning ECU and Receiver 5.167,2.625 6.865,3 1.698,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 1.323,0.51 1.521,0.656 0.198,0.146 10 false IG 5.698,1.094 6.177,1.385 0.479,0.292 10 false RDA 5.708,1.583 6.146,1.844 0.438,0.26 10 false PRG 5.469,1.5 5.677,1.813 0.208,0.313 10 false 5 5.438,0.979 5.646,1.188 0.208,0.208 10 false 16 1.188,1.073 1.521,1.24 0.333,0.167 10 false RDA 1.198,1.573 1.521,1.729 0.323,0.156 10 false PRG 1.594,0.406 1.688,0.542 0.094,0.135 10 false 1 1.594,0.969 1.698,1.146 0.104,0.177 10 false 4 1.604,1.469 1.771,1.656 0.167,0.188 10 false 5 1.219,2.135 1.552,2.292 0.333,0.156 10 false GND 1.594,2.031 1.875,2.281 0.281,0.25 10 false 12 3.885,0.542 5.073,0.938 1.188,0.396 10 false from IG Circuit 0.156,2.708 0.448,2.854 0.292,0.146 10 false M48 5.146,2.469 5.479,2.635 0.333,0.167 10 false G59 2.229,0.698 3.344,0.99 1.115,0.292 10 false ECU-IG NO. 1

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver after the ECU has been replaced.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the M48 tire pressure warning ECU and receiver connector.


b.

Disconnect the G59 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M48-4 (RDA) - G59-16 (RDA) Always Below 1 Ω
M48-4 (RDA) or G59-16 (RDA) - Body ground Always 10 kΩ or higher




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF TIRE PRESSURE WARNING ECU AND RECEIVER)
a.
U183580E02
1.219,1.219 0.813,1.708 0.813,1.708 0.813,1.823 false 2.198,1.354 2.625,1.26 2.625,1.26 2.74,1.26 false 0.365,1.125 0.698,1.292 0.333,0.167 10 false M48 0.104,0.104 0.313,0.292 0.208,0.188 10 false *a 0.719,1.844 0.938,2.042 0.219,0.198 10 false IG 2.792,1.177 3.135,1.344 0.344,0.167 10 false GND

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M48-12 (GND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M48-1 (IG) - Body ground Power switch on (IG) 10 to 16 V



Text in Illustration
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


OK

3.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER
a.

Replace the tire pressure warning ECU and receiver (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER>REMOVAL).



NEXT

4.CHECK DTC OUTPUT (B1247)
4.CHECK DTC OUTPUT (B1247)

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check for DTCs (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1247 is not output.




OK

END

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)