Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2015.11
RM2170E _53 Suspension _057019 TIRE PRESSURE MONITORING _0278018 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2179/79  Tire Pressure Monitor ECU Communication Stop  


DESCRIPTION

The main body ECU (multiplex network body ECU) sends signals to the tire pressure warning ECU and receiver via a direct line.

DTC No. DTC Detection Condition Trouble Area
C2179/79 Communication between the main body ECU (multiplex network body ECU) and tire pressure warning ECU and receiver is interrupted for 10 seconds or more.
·

Main body ECU (Multiplex network body ECU)

·

Wire harness or connector

·

Tire pressure warning ECU and receiver



WIRING DIAGRAM

C240095E26
2.188,1.115 2.583,1.333 0.396,0.219 10 false PRG 2.583,1 2.875,1.26 0.292,0.26 10 false 4 4.635,1.115 5.031,1.281 0.396,0.167 10 false PRG 4.438,0.99 4.604,1.156 0.167,0.167 10 false 5 4.448,1.979 4.74,2.167 0.292,0.188 10 false M48 4.729,1.979 6.5,2.417 1.771,0.438 10 false Tire Pressure Warning ECU and Receiver 0.479,1.969 0.76,2.135 0.281,0.167 10 false G59 0.802,1.969 2.469,2.396 1.667,0.427 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver after the ECU has been replaced.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the M48 tire pressure warning ECU and receiver connector.


b.

Disconnect the G59 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M48-5 (PRG) - G59-4 (PRG) Always Below 1 Ω
M48-5 (PRG) or G59-4 (PRG) - Body ground Always 10 kΩ or higher




OK

2.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER
a.

Replace the tire pressure warning ECU and receiver (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER>REMOVAL).



NEXT

3.CHECK DTC OUTPUT
3.CHECK DTC OUTPUT

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check for DTCs (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC C2179/79 is not output.




OK

END

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)