Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › from 2015.11
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the ABS warning light remains on:

·

The skid control ECU (brake booster with master cylinder assembly) connector is disconnected from the brake booster with master cylinder assembly.

·

There is a malfunction in the skid control ECU (brake booster with master cylinder assembly) internal circuit.

·

There is an open in the harness between the combination meter assembly and the skid control ECU (brake booster with master cylinder assembly).

·

The ABS control system is defective.


HINT:

In some cases, the intelligent tester cannot be used when the skid control ECU (brake booster with master cylinder assembly) is malfunctioning.


WIRING DIAGRAM

C248086E14
0.688,0.75 1.094,0.896 0.406,0.146 10 false CANL 0.688,1.281 1.094,1.427 0.406,0.146 10 false CANH 1.177,0.656 1.354,0.792 0.177,0.135 10 false 32 1.177,1.177 1.354,1.313 0.177,0.135 10 false 31 0.083,5.844 0.302,5.99 0.219,0.146 10 false G1 0.344,5.844 1.583,6.177 1.24,0.333 10 false Combination Meter Assembly 1.938,1.896 3.344,2.094 1.406,0.198 10 false from IG1 NO. 1 Relay 4.229,2.031 5.146,2.177 0.917,0.146 10 false ECU-IG NO. 1 6.146,0.74 6.552,0.885 0.406,0.146 10 false CA1L 6.146,1.292 6.573,1.438 0.427,0.146 10 false CA1H 6.146,1.854 6.396,2 0.25,0.146 10 false IG1 6.146,2.385 6.563,2.531 0.417,0.146 10 false GND 5.01,5.844 7.094,6.198 2.083,0.354 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 6.146,2.896 6.563,3.042 0.417,0.146 10 false GND2 6.146,3.396 6.563,3.542 0.417,0.146 10 false GND3 6.146,3.896 6.563,4.042 0.417,0.146 10 false GND4 6.146,4.417 6.563,4.563 0.417,0.146 10 false GND5 6.146,4.927 6.563,5.073 0.417,0.146 10 false GND6 5.854,0.635 6.031,0.771 0.177,0.135 10 false 38 5.854,1.167 6.083,1.302 0.229,0.135 10 false 37 5.854,1.75 6.083,1.885 0.229,0.135 10 false 16 5.854,2.271 6.083,2.406 0.229,0.135 10 false 28 5.854,2.729 6.083,2.865 0.229,0.135 10 false 27 5.854,3.271 6.083,3.406 0.229,0.135 10 false 26 5.854,3.802 6.083,3.938 0.229,0.135 10 false 25 5.854,4.302 6.083,4.438 0.229,0.135 10 false 24 5.854,4.813 6.083,4.948 0.229,0.135 10 false 23 4.688,5.844 5.01,5.99 0.323,0.146 10 false A41

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
DTC is not output. A
DTC is output. B




A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake booster with master cylinder assembly) connector is securely connected.

OK:

The connector is securely connected.




OK

3.CHECK AUXILIARY BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK AUXILIARY BATTERY
a.

Check the auxiliary battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Auxiliary battery Power switch on (IG) 11 to 14 V
Auxiliary battery Power switch on (ready) 11 to 15.5 V




OK

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG

CHARGE OR REPLACE AUXILIARY BATTERY

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
U183563E01
0.196,0.187 0.401,0.345 0.205,0.158 10 *a 0.265,0.857 0.553,1.015 0.288,0.158 10 A41 1.363,1.865 1.102,2.711 false 0.978,2.754 1.335,2.911 0.357,0.158 10 IG1

Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A41-16 (IG1) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))



OK

5.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
U183556E01
0.196,0.187 0.401,0.345 0.205,0.158 10 *a 0.265,0.857 0.553,1.015 0.288,0.158 10 A41 2.279,1.803 2.279,0.999 false 2.381,1.803 2.731,0.666 false 2.17,1.803 1.82,0.666 false 2.031,0.806 2.440,0.963 0.409,0.158 10 GND4 1.554,0.488 1.963,0.645 0.409,0.158 10 GND5 2.493,0.488 2.902,0.645 0.409,0.158 10 GND3 2.476,1.801 3.025,0.982 false 2.815,0.806 3.225,0.963 0.409,0.158 10 GND2 2.08,1.801 1.53,0.982 false 1.251,0.806 1.660,0.963 0.409,0.158 10 GND6 2.648,1.994 2.942,2.761 false 2.776,2.782 3.134,2.940 0.357,0.158 10 GND

Turn the power switch off (lock).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-28 (GND) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A41-27 (GND2) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A41-26 (GND3) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A41-25 (GND4) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A41-24 (GND5) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A41-23 (GND6) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))



OK

6.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

6.INSPECT COMBINATION METER ASSEMBLY
a.

Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.


b.

Perform the Active Test of the combination meter assembly (meter CPU) using the intelligent tester (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).


c.

Check the combination meter assembly.

OK:

The ABS warning light turns on or off in accordance with intelligent tester operation.


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE COMBINATION METER ASSEMBLY