Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2014.12–2015.11
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1210/36  Zero Point Calibration of Yaw Rate Sensor Undone  C1336/98  Zero Point Calibration of Acceleration Sensor Undone  


DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).

If there are any problems in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTCs U0123/62 (Lost Communication with Yaw Rate Sensor Module) and U0124/95 (Lost Communication with Lateral Acceleration Sensor Module) will be stored.

These DTCs (C1210/36 and C1336/98) will also be stored when calibration has not been completed.

DTC No. INF Code DTC Detection Condition Trouble Area
C1210/36 - Yaw rate sensor zero point calibration is incomplete.
·

Zero point calibration undone

·

Yaw rate and acceleration sensor (Airbag sensor assembly)

·

Skid control ECU (Brake booster with master cylinder assembly)


(Perform zero point calibration and check for DTCs. If no DTCs are output again, the sensor is normal.)
C1336/98 - Either of the following is detected:
1.

The vehicle is driven normally without zero point calibration completed.

2.

After completing zero point calibration, zero point voltage of the sensor is not within the range of 2.38 to 2.62 V.


·

Zero point calibration undone

·

Yaw rate and acceleration sensor (Airbag sensor assembly)

·

Skid control ECU (Brake booster with master cylinder assembly)


(Perform zero point calibration and check for DTCs. If no DTCs are output again, the sensor is normal.)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).

·

When replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION).



HINT:

When U0123/62 and/or U0124/95 is output together with C1210/36 and/or C1336/98, inspect and repair trouble areas indicated by U0123/62 and/or U0124/95 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>U0073/94).


PROCEDURE

1.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
a.

Perform zero point calibration of the yaw rate and acceleration sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION).



NEXT

2.RECONFIRM DTC
2.RECONFIRM DTC
a.

Turn the power switch off (lock).



c.

Turn the power switch on (ready).


d.

Drive the vehicle at a speed of 30 km/h (18 mph) or more, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1210/36 and/or C1336/98 are output. A
DTCs C1210/36 and C1336/98 are not output. B


HINT:
·

The DTCs are recorded because zero point calibration has not been completed.

·

End the procedure if the same DTCs are not recorded after completion of zero point calibration.





A

3.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION

B

END

3.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Turn the power switch off (lock).


b.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION).

OK:

The sensor is tightened to the specified torque.

The sensor is not tilted.




OK

4.REPLACE AIRBAG SENSOR ASSEMBLY

NG

4.REPLACE AIRBAG SENSOR ASSEMBLY
a.

Replace the yaw rate and acceleration sensor (airbag sensor assembly) (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL).

NOTICE:

Check the yaw rate and acceleration sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).




NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC

b.

Turn the power switch on (ready).


c.

Drive the vehicle at a speed of 30 km/h (18 mph) or more, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1210/36 and/or C1336/98 are output (for LHD). A
DTCs C1210/36 and/or C1336/98 are output (for RHD). B
DTCs C1210/36 and C1336/98 are not output. C




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

END