Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2014.12–2015.11
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1231/31  Steering Angle Sensor Circuit Malfunction  


DESCRIPTION

The skid control ECU receives steering angle sensor signals via the CAN communication system. When a malfunction occurs in the communication line with the steering angle sensor (spiral cable with sensor sub-assembly), DTC U0126/63 (Lost Communication with Steering Angle Sensor Module) is stored.

DTC No. INF Code DTC Detection Condition Trouble Area
C1231/31 701 While steering angle sensor communication is enabled, a malfunction signal output is received during the sensor self-check (sensor malfunction). Steering angle sensor (Spiral cable with sensor sub-assembly) internal malfunction
↑ 702 While steering angle sensor communication is enabled, a malfunction signal output is received during the sensor self-check (internal malfunction). ↑
↑ 703 While steering angle sensor communication is enabled, a malfunction signal output is received during the sensor self-check (+B malfunction). ↑

WIRING DIAGRAM

C167662E87
0.063,4.01 0.344,4.177 0.281,0.167 10 false G30 0.896,3.26 1.208,3.427 0.313,0.167 10 false ESS 0.792,0.604 1.198,0.771 0.406,0.167 10 false CANL 0.792,1.177 1.208,1.344 0.417,0.167 10 false CANH 0.906,1.896 1.198,2.063 0.292,0.167 10 false BAT 1.01,2.563 1.24,2.729 0.229,0.167 10 false IG 1.281,0.521 1.479,0.708 0.198,0.188 10 false 3 1.281,1.094 1.469,1.281 0.188,0.188 10 false 4 1.281,1.802 1.406,1.99 0.125,0.188 10 false 6 1.281,2.479 1.385,2.667 0.104,0.188 10 false 5 1.281,3.146 1.385,3.333 0.104,0.188 10 false 2 2.25,2.094 2.688,2.25 0.438,0.156 10 false DOME 2.01,2.781 2.917,2.938 0.906,0.156 10 false ECU-IG NO. 1 3.906,1.938 5.292,2.104 1.385,0.167 10 false from Auxiliary Battery 3.896,2.615 5.333,2.781 1.438,0.167 10 false from IG1 NO. 1 Relay 5.792,1.115 6,1.292 0.208,0.177 10 false 37 4.708,4 4.979,4.146 0.271,0.146 10 false A41 6.042,0.615 6.469,0.792 0.427,0.177 10 false CA1L 6.042,1.198 6.469,1.375 0.427,0.177 10 false CA1H 5.792,0.51 5.969,0.688 0.177,0.177 10 false 38 5.021,4 7.094,4.375 2.073,0.375 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.396,4.01 2.563,4.365 2.167,0.354 10 false Steering Angle Sensor (Spiral Cable with Sensor Sub-assembly) 2.208,1.813 2.313,2 0.104,0.188 10 false 2 2.635,1.813 2.74,2 0.104,0.188 10 false 1

CAUTION / NOTICE / HINT

HINT:
·

When U0126/63 is output together with C1231/31, inspect and repair the trouble areas indicated by U0126/63 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>U0073/94).

·

When a speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) is malfunctioning, DTCs for the steering angle sensor (spiral cable with sensor sub-assembly) may be output even when the steering angle sensor (spiral cable with sensor sub-assembly) is normal. When DTCs for a speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) are output together with DTCs for the steering angle sensor (spiral cable with sensor sub-assembly), inspect and repair the speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) first, and then inspect and repair the steering angle sensor (spiral cable with sensor sub-assembly).



PROCEDURE

1.CHECK DTC

b.

Turn the power switch off (lock).


c.

Turn the power switch on (IG) again and check that no CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).


d.

Drive the vehicle at a speed of 35 km/h (22 mph) and turn the steering wheel to the right and left check that no speed sensor and/or yaw rate and acceleration sensor DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1231/31 is output. A
CAN communication system DTC is output. B
Speed sensor and/or yaw rate and acceleration sensor DTC is output. C
DTC C1231/31 is not output. D


HINT:
·

When DTCs indicating CAN communication system malfunctions are output, repair the CAN communication system before repairing each corresponding sensor.

·

If there is a malfunction in the speed sensor or yaw rate and acceleration sensor (airbag sensor assembly), an abnormal value may be output although the steering angle sensor (spiral cable with sensor sub-assembly) is normal.

·

If speed sensor and the yaw rate and acceleration sensor DTCs are output simultaneously, repair the sensors and inspect the steering angle sensor (spiral cable with sensor sub-assembly).





A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

B

C

D

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
U183508E01
0.323,1.291 0.613,1.447 0.290,0.156 10 G30 0.194,0.209 0.413,0.364 0.218,0.156 10 *a 2.125,2.358 1.629,1.188 false 2.368,2.358 2.864,1.188 false 1.5,0.991 1.781,1.146 0.281,0.156 10 IG 2.686,0.991 2.988,1.146 0.302,0.156 10 BAT

Turn the power switch off (lock).


b.

Remove the steering wheel and the column cover.


c.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.

Disconnect the steering angle sensor (spiral cable with sensor sub-assembly) connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G30-5 (IG) - Body ground Power switch on (IG) 11 to 14 V
G30-6 (BAT) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Angle Sensor (Spiral Cable with Sensor Sub-assembly))



OK

3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.
U183509E01
0.323,1.291 0.671,1.447 0.348,0.156 10 G30 0.194,0.209 0.413,0.364 0.218,0.156 10 *a 1.389,2.358 1.884,1.188 false 1.707,0.991 2.008,1.146 0.302,0.156 10 ESS

Turn the power switch off (lock).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G30-2 (ESS) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Steering Angle Sensor (Spiral Cable with Sensor Sub-assembly))

HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)