The skid control ECU receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.
The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).
If there are any problems in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTCs U0123/62 (Lost Communication with Yaw Rate Sensor Module) and U0124/95 (Lost Communication with Lateral Acceleration Sensor Module) are stored.
These DTCs are also output when calibration has not been completed.
DTC C1279/79 will be cleared when the yaw rate and acceleration sensor (airbag sensor assembly) sends a yaw rate and/or acceleration signal or when Test Mode ends. DTC C1279/79 is output only in Test Mode.
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1234/34 | 711 | While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Sensor 1 (GL1) malfunction). | Yaw rate and acceleration sensor (Airbag sensor assembly) internal malfunction |
| ↑ | 712 | While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Sensor 2 (GL2) malfunction). | ↑ |
| ↑ | 713 | While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Zero point calibration malfunction). | ↑ |
| ↑ | 714 | While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Two-value comparison malfunction). | ↑ |
| C1243/43 | 561 | An acceleration sensor malfunction occurs 16 times or more when the vehicle speed drops from above 30 km/h (19 mph) to 0 km/h (0 mph). | Yaw rate and acceleration sensor (Airbag sensor assembly) internal stuck malfunction |
| ↑ | 562
563 564 565 |
A stuck acceleration sensor value is determined. | ↑ |
| C1244/44 | 571 | Either of the following is detected:
1.
Difference between GL1 and GL2 does not become less than 0.4 G for 60 seconds or more after reaching 0.6 G when the vehicle is stopped. 2.
A malfunction signal from the acceleration sensor is received. |
·
Yaw rate and acceleration sensor (Airbag sensor assembly) installed improperly ·
Yaw rate and acceleration sensor (Airbag sensor assembly) |
| C1245/45 | 581 | Difference between longitudinal G calculated from the acceleration sensor value and that calculated from the vehicle speed exceeds 0.35 G for 60 seconds or more. | ·
Yaw rate and acceleration sensor (Airbag sensor assembly) installed improperly ·
Yaw rate and acceleration sensor (Airbag sensor assembly) |
| C1381/97 | 601 | While yaw rate and acceleration sensor communication is enabled, a supply voltage malfunction signal is received from the sensor for 10 seconds. | ·
Yaw rate and acceleration sensor (Airbag sensor assembly) supply voltage shut down ·
Yaw rate and acceleration sensor (Airbag sensor assembly) ·
Skid control ECU (Brake booster with master cylinder assembly) |
| C1279/79 | - | Detected only during Test Mode. | ·
Sensor installation ·
Yaw rate and acceleration sensor (Airbag sensor assembly) |
When replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION).
When U0123/62 and/or U0124/95 is output together with C1234/34, C1243/43, C1244/44, C1245/45, and/or C1381/97, inspect and repair the trouble areas indicated by U0123/62 and/or U0124/95 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>U0073/94).
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off (lock).
Turn the power switch on (ready).
Drive the vehicle at a speed of 30 km/h (19 mph) or more, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.
Turn the power switch on (IG) again and check that no CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).
Check if DTC C1210/36 (Zero Point Calibration of Yaw Rate Sensor Undone) or C1336/98 (Zero Point Calibration of Acceleration Sensor Undone) is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs (C1210/36, C1336/98 and CAN communication system DTC) are not output. | A |
| CAN communication system DTC is output. | B |
| DTCs C1210/36 and/or C1336/98 are output. | C |
A
B
(See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
C
Turn the power switch off (lock).
Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION).
The sensor is tightened to the specified torque.
The sensor is not tilted.
OK
NG
(See pageVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION)
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the yaw rate and acceleration sensor (airbag sensor assembly) connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G18-21 (IG2) - Body ground | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly)) |
OK
NG
Turn the power switch off (lock).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G18-25 (E1) - Body ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| G18-26 (E2) - Body ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| *a | Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly)) |
Check the yaw rate and acceleration sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).
OK
NG