The skid control ECU detects decreases in the accumulator pressure according to the data from the accumulator pressure sensor, and then starts and stops the pump motor by operating the motor relay.
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1252/52 | 311 | The pump motor is operating continuously for 178 seconds or more. (When relay malfunction is 98 seconds or more.) | ·
Short in motor circuit or motor monitor circuit ·
Motor relay stuck ·
Accumulator pressure sensor malfunction in brake actuator (Brake booster with master cylinder assembly) ·
Skid control ECU (Brake booster with master cylinder assembly) |
| C1253/53 | 321 | With the IG1 terminal voltage 9.5 V or more, the motor drive monitor remains off for 0.2 seconds or more after a motor drive on request. | ·
Open in motor circuit or motor monitor circuit ·
Skid control ECU (Brake booster with master cylinder assembly) |
| ↑ | 322 | The motor drive monitor remains on for 2 seconds or more after a motor drive off request. | ·
Short in motor circuit or motor monitor circuit ·
Skid control ECU (Brake booster with master cylinder assembly) |
| ↑ | 323 | The skid control ECU internal motor drive logical inconsistency continues for 2 seconds or more. | Skid control ECU (Brake booster with master cylinder assembly) |
| ↑ | 324 | An open circuit in both skid control ECU internal motor relays 1 and 2. | ·
Open in motor circuit or motor monitor circuit ·
Skid control ECU (Brake booster with master cylinder assembly) |
| ↑ | 325 | An open circuit in both skid control ECU internal motor relays 1 and 3. | ↑ |
| ↑ | 326 | An open circuit in both skid control ECU internal motor relays 2 and 3. | ↑ |
| ↑ | 327 | An open circuit in skid control ECU internal motor relay 1. | ↑ |
| ↑ | 328 | An open circuit in skid control ECU internal motor relay 2. | ↑ |
| ↑ | 329 | An open circuit in skid control ECU internal motor relay 3. | ↑ |
When replacing the skid control ECU (brake booster with master cylinder assembly) or brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Select the Active Test on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| ECB* Motor Relay | ABS motor relay | Relay ON/OFF | - |
*: Electronically Controlled Brake System
Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| ECB* Motor Relay | ABS motor relay / ON or OFF | ON: Relay on
OFF: Relay off |
- |
*: Electronically Controlled Brake System
Check the operating condition of the ABS motor relay when operating it using the intelligent tester.
| Result | Proceed to |
|---|---|
| ABS motor relay in the Data List turns ON/OFF using the Active Test. | A |
| ABS motor relay in the Data List does not change using the Active Test. | B |
A
B
Turn the power switch off (lock).
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the brake booster pump assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A45-1 (BM1) - A45-2 (GND1) | Always | Below 10 Ω |
| A46-2 (BM2) - A46-1 (GND2) | Always | Below 10 Ω |
| A45-1 (BM1) - A46-2 (BM2) | Always | Below 1 Ω |
| A45-2 (GND1) - A46-1 (GND2) | Always | Below 1 Ω |
| *a | Component without harness connected
(Brake Booster Pump Assembly) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A45-2 (GND1) - Body ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| A46-1 (GND2) - Body ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| *a | Front view of wire harness connector
(to Brake Booster Pump Assembly) |
OK
NG
Reconnect the brake booster pump assembly connectors.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Accumulator Sensor | Accumulator pressure sensor /
Min.: 0.00 V, Max.: 5.00 V |
Specified value: 2.90 to 4.20 V | When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator |
Wait for 30 seconds without depressing the brake pedal.
Check that the accumulator pressure sensor output value change is within the specified range.
Accumulator pressure sensor output value change is less than 0.55 V.
OK
NG
Turn the power switch off (lock).
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (IG).
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1252/52 and C1253/53 are not output. | A |
| DTCs C1252/52 and/or C1253/53 are output (for LHD). | B |
| DTCs C1252/52 and/or C1253/53 are output (for RHD). | C |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
Turn the power switch off (lock).
Check that the ABS MTR NO. 1 (30 A) and ABS MTR NO. 2 (30 A) fuses are normal.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A41-1 (MRI1) - Body ground | Always | 11 to 14 V |
| A41-2 (MRI2) - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the brake booster pump assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A41-29 (MRO1) - A45-1 (BM1) | Always | Below 1 Ω |
| A41-29 (MRO1) - Body ground | Always | 10 kΩ or higher |
| A41-30 (MRO2) - A46-2 (BM2) | Always | Below 1 Ω |
| A41-30 (MRO2) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Select the Active Test on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
The Active Test can be performed when the following conditions are met.
ABS main relay is on.
Shift lever is in P.
Parking brake is applied.
Vehicle speed is 0 km/h (0 mph).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| ECB* Solenoid (SMC/SRC/SCC) | Switching solenoid valve (SMC/SRC/SCC) | Solenoid ON/OFF | Operation sound of solenoid (clicking sound) can be heard |
*: Electronically Controlled Brake System
Perform the Active Test of the solenoid using the intelligent tester.
Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Wheel Cylinder Pressure Sensor | Wheel cylinder pressure sensor / Min.: 0.00 V, Max.: 5.00 V | When brake pedal released: 0.10 to 0.90 V | Reading increases when brake pedal is depressed |
Check that the output value of the wheel cylinder pressure sensor does not increase.
The output value of the wheel cylinder pressure sensor does not increase.
If the output value increases, there may be brake fluid leaks in the brake actuator.
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D