Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2014.12–2015.11
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1365/54  Accumulator Pressure Sensor Malfunction  


DESCRIPTION

The accumulator pressure sensor is built into the brake actuator (brake booster with master cylinder assembly).

The skid control ECU detects the accumulator pressure from the data sent from the accumulator pressure sensor, and then starts and stops the pump motor by operating the motor relay.

This DTC may be stored if the accumulator pressure drops due to frequent braking (this is not a malfunction).

DTC No. INF Code DTC Detection Condition Trouble Area
C1365/54 331 Sensor supply voltage (VACC) is 4.54 V or less, or 5.46 V or more for 0.8 seconds or more. Brake booster with master cylinder assembly
↑ 332 Accumulator pressure sensor output voltage (PACC) is less than 8%, or 88% or more of sensor supply voltage for 0.8 seconds or more (less than 0.4 V, or 4.4 V or more for 0.8 seconds or more). ↑
↑ 333 Fluctuation of sensor output is out of specification (the difference between the present value and last value is 7.5 MPa (77.0 kgf/cm2, 1088 psi)) for 0.8 seconds or more. ↑
↑ 334 With the vehicle driven at 6 km/h (4 mph) or more and output value of the accumulator pressure sensor 19.7 MPa (200.8 kgf/cm2, 2857 psi) or less, the pump motor does not operate for 12 seconds or more. ↑

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly) or brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ACCUMULATOR PRESSURE SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Accumulator Sensor Accumulator pressure sensor /
Min.: 0.00 V, Max.: 5.00 V
Specified value: 2.90 to 4.20 V When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator


d.

Wait for 30 seconds without depressing the brake pedal.


e.

Check that the accumulator pressure sensor output value change is within the specified range.

OK:

Accumulator pressure sensor output value change is less than 0.55 V.


Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

2.RECONFIRM DTC

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

2.RECONFIRM DTC
a.

Turn the power switch off (lock).



c.

Perform a road test.


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1365/54 is not output. A
DTC C1365/54 is output (for LHD). B
DTC C1365/54 is output (for RHD). C




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY