Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2014.12–2015.11
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1311/11  Open in Main Relay 1 Circuit  C1312/12  Short in Main Relay 1 Circuit  


DESCRIPTION

The ABS main relay supplies power to the changeover solenoid and the linear solenoid.

The ABS main relay remains on for approximately 2 minutes after the power switch is turned off (lock) and the input of brake pedal operation signals stops, and supplies power to the system to keep it ready to operate.

DTC No. INF Code DTC Detection Condition Trouble Area
C1311/11 1 Either of the following is detected:
1.

When the power switch is on (ready):

The ABS main relay contact is not turned ON (BS terminal voltage 3.5 V or more) for 0.2 seconds or more when ABS main relay ON is requested while IG1 terminal voltage is 9.5 V or more.

2.

When the power switch is off (lock):

The ABS main relay contact is not turned ON (BS terminal voltage 3.5 V or more) for 0.2 seconds or more when ABS main relay ON is requested.


·

Open or short in ABS main relay circuit

·

Skid control ECU (Brake booster with master cylinder assembly)


C1312/12 2 The ABS main relay contact is turned ON (BS terminal voltage 3.5 V or more) for 4.5 seconds or more when ABS main relay OFF is requested from the ECU.
·

Short in ABS main relay circuit

·

ABS main relay internal stuck

·

Skid control ECU (Brake booster with master cylinder assembly)



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS MAIN RELAY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Select the Active Test on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
ECB* Main Relay ABS main relay Relay ON/OFF -

*: Electronically Controlled Brake System



ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ECB* Main Relay ABS main relay / ON or OFF ON: Relay on
OFF: Relay off
-

*: Electronically Controlled Brake System

e.

Check that the condition of the ABS main relay observed on the intelligent tester changes according to tester operation.

Result:
Result Proceed to
ABS main relay in the Data List turns ON/OFF using the Active Test. A
ABS main relay in the Data List does not change using the Active Test. B




A

2.CHECK HARNESS AND CONNECTOR (BS TERMINAL)

B

4.CHECK HARNESS AND CONNECTOR (BI TERMINAL)
2.CHECK HARNESS AND CONNECTOR (BS TERMINAL)
a.
U183559E01
0.196,0.187 0.401,0.345 0.205,0.158 10 *a 0.265,0.857 0.553,1.015 0.288,0.158 10 A41 2.678,1.821 2.914,2.719 false 2.799,2.766 3.087,2.923 0.288,0.158 10 BS

Turn the power switch off (lock).


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A41-15 (BS) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BS CIRCUIT)

3.RECONFIRM DTC
a.

Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.



c.

Turn the power switch on (IG).


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1311/11 and C1312/12 are not output. A
DTCs C1311/11 and/or C1312/12 are output (for LHD). B
DTCs C1311/11 and/or C1312/12 are output (for RHD). C




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BI TERMINAL)
a.
U183560E02
2.469,1.729 2.76,2.813 false 0.198,0.188 0.385,0.344 0.188,0.156 10 false *a 0.281,0.885 0.573,1.042 0.292,0.156 10 false A41 2.688,2.823 2.865,2.979 0.177,0.156 10 false BI

Turn the power switch off (lock).


b.

Check that the ABS NO. 1 (20 A) and ABS NO. 2 (10 A) fuses are normal.


c.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.

Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A41-14 (BI) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))



OK

5.CHECK HARNESS AND CONNECTOR (BS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BI CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (BS TERMINAL)
a.
U183559E01
0.196,0.187 0.401,0.345 0.205,0.158 10 *a 0.265,0.857 0.553,1.015 0.288,0.158 10 A41 2.678,1.821 2.914,2.719 false 2.799,2.766 3.087,2.923 0.288,0.158 10 BS

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A41-15 (BS) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (BS CIRCUIT)