Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › from 2015.11
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1241/41  Low Battery Positive Voltage  C1242/42  Open in IG1 / IG2 Power Source Circuit  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU power source voltage drops, or there is insufficient voltage to operate the ABS main relay, the skid control ECU will store these DTCs.

These DTCs may also be stored if the auxiliary battery voltage drops below 9.5 V.

HINT:

DTC C1256/56 (Accumulator Low Pressure) may also be memorized if there is a drop in power source voltage.


DTC No. INF Code DTC Detection Condition Trouble Area
C1241/41 101 Any of the following conditions when the BS terminal voltage is 9.3 V or less:
1.

Vehicle not decelerated (brake pedal is not depressed) for 3 seconds or more.

2.

While depressing the brake pedal, linear solenoid current does not satisfy 1.34 A.

3.

Vehicle decelerated (brake pedal is depressed) for 0.06 seconds.


·

Improperly connected connector, deformation or corrosion of terminals

·

Auxiliary battery

·

Hybrid control system (Charging circuit)

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 102 Either of the following conditions when the ECU internal voltage is 6.3 V or less:
1.

When main relay ON is requested, voltage of the relay connection does not exceed 3.5 V for 0.22 seconds or more.

2.

Sensor supply voltage is 4.75 V or less, or 5.25 V or more for 0.06 seconds.

3.

Accumulator pressure sensor output voltage is 4.54 V or less, or 5.46 V or more for 0.06 seconds.


↑
↑ 551 When driving at 3 km/h (1.9 mph) or more, IG1 terminal voltage is 9.5 V or less, or VM1 voltage is 8.6 V or less for 10 seconds or more. ↑
↑ 552 When VM1 voltage is 8.6 V or less, sensor supply voltage is low for 60 seconds or more. ↑
↑ 553 VM1 voltage is 16.6 V or more for 0.8 seconds. ↑
C1242/42 111 Voltage is not applied to the IG1 terminal (less than 3.5 V), and applied to the IG2 terminal (9.5 V or more) for 4 seconds or more.
·

Open or short in IG1 circuit

·

Improperly connected connector, deformation or corrosion of terminals

·

Smart entry and start system (IG start circuit)

·

Auxiliary battery

·

Hybrid control system (Charging circuit)

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 112 Voltage is not applied to the IG2 terminal (less than 3.5 V), and applied to the IG1 terminal (9.5 V or more) for 4 seconds or more.
·

Open or short in IG2 circuit

·

Improperly connected connector, deformation or corrosion of terminals

·

Smart entry and start system (IG start circuit)

·

Auxiliary battery

·

Hybrid control system (Charging circuit)

·

Skid control ECU (Brake booster with master cylinder assembly)



WIRING DIAGRAM

C256729E02
0.604,0.813 1.99,0.969 1.385,0.156 10 false from Auxiliary Battery 5.938,0.76 6.188,0.927 0.25,0.167 10 false BI 5.656,5.927 5.896,6.073 0.24,0.146 10 false 23 5.938,1.365 6.25,1.531 0.313,0.167 10 false BS 5.938,3.146 6.354,3.313 0.417,0.167 10 false GND 5.938,3.708 6.354,3.875 0.417,0.167 10 false GND2 5.938,4.292 6.354,4.458 0.417,0.167 10 false GND3 5.938,4.896 6.354,5.063 0.417,0.167 10 false GND4 5.938,5.469 6.354,5.635 0.417,0.167 10 false GND5 5.938,6.073 6.354,6.24 0.417,0.167 10 false GND6 3.917,0.927 4.688,1.083 0.771,0.156 10 false ABS NO. 2 4.052,0.635 4.156,0.781 0.104,0.146 10 false 1 4.427,0.635 4.531,0.781 0.104,0.146 10 false 2 5.938,1.948 6.25,2.115 0.313,0.167 10 false IG1 5.938,2.563 6.25,2.729 0.313,0.167 10 false IG2 3.948,1.531 4.688,1.688 0.74,0.156 10 false ABS NO. 1 0.594,1.99 1.969,2.219 1.375,0.229 10 false from IG1 NO. 1 Relay 4.052,1.833 4.156,1.979 0.104,0.146 10 false 1 4.427,1.833 4.531,1.979 0.104,0.146 10 false 2 3.833,2.125 4.74,2.281 0.906,0.156 10 false ECU-IG NO. 1 4.948,7.021 7.104,7.385 2.156,0.365 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.646,7.021 4.917,7.167 0.271,0.146 10 false A41 5.656,5.344 5.896,5.49 0.24,0.146 10 false 24 5.656,4.76 5.896,4.906 0.24,0.146 10 false 25 5.656,4.167 5.896,4.313 0.24,0.146 10 false 26 5.656,3.583 5.896,3.729 0.24,0.146 10 false 27 5.656,3.021 5.896,3.167 0.24,0.146 10 false 28 5.656,0.635 5.875,0.781 0.219,0.146 10 false 14 5.656,1.229 5.896,1.375 0.24,0.146 10 false 15 5.656,1.833 5.875,1.979 0.219,0.146 10 false 16 5.656,2.427 5.875,2.573 0.219,0.146 10 false 12 0.99,2.604 2.021,2.823 1.031,0.219 10 false from IG2 Relay 4.052,2.427 4.156,2.573 0.104,0.146 10 false 1 4.427,2.427 4.531,2.573 0.104,0.146 10 false 2 3.958,2.719 4.604,2.875 0.646,0.156 10 false IG2 NO. 2

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK SMART ENTRY AND START SYSTEM (for Start Function)
a.

Check if smart entry and start system (for start function) DTCs are output (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC is not output. A
DTC is output. B




A

2.CHECK HYBRID CONTROL SYSTEM

B

2.CHECK HYBRID CONTROL SYSTEM
a.

Check if hybrid control system DTCs are output (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC is not output. A
DTC is output. B




A

3.CHECK DTC

B

3.CHECK DTC
a.

Check that no main relay DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Main relay malfunction DTC is not output. A
Main relay malfunction DTC is output. B




A

4.CHECK AUXILIARY BATTERY

B

4.CHECK AUXILIARY BATTERY
a.

Check the auxiliary battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Auxiliary battery Power switch on (IG) 11 to 14 V
Auxiliary battery Power switch on (ready) 11 to 15.5 V




OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

CHARGE OR REPLACE AUXILIARY BATTERY

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
U183555E01
0.196,0.187 0.380,0.345 0.184,0.158 10 *a 0.265,0.857 0.553,1.015 0.288,0.158 10 A41 1.361,1.823 1.067,2.778 false 0.929,2.791 1.238,2.948 0.309,0.158 10 IG1 2.659,1.823 2.953,2.778 false 2.88,2.791 3.105,2.948 0.225,0.158 10 BS 2.275,1.676 1.872,0.72 false 2.484,1.676 2.887,0.72 false 2.819,0.531 3.045,0.688 0.225,0.158 10 BI 1.716,0.531 2.024,0.688 0.309,0.158 10 IG2

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A41-14 (BI) - Body ground Always 11 to 14 V
A41-15 (BS) - Body ground Always 11 to 14 V
A41-16 (IG1) - Body ground Power switch on (IG) 11 to 14 V
A41-12 (IG2) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))



OK

6.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

6.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
U183556E01
0.196,0.187 0.401,0.345 0.205,0.158 10 *a 0.265,0.857 0.553,1.015 0.288,0.158 10 A41 2.279,1.803 2.279,0.999 false 2.381,1.803 2.731,0.666 false 2.17,1.803 1.82,0.666 false 2.031,0.806 2.440,0.963 0.409,0.158 10 GND4 1.554,0.488 1.963,0.645 0.409,0.158 10 GND5 2.493,0.488 2.902,0.645 0.409,0.158 10 GND3 2.476,1.801 3.025,0.982 false 2.815,0.806 3.225,0.963 0.409,0.158 10 GND2 2.08,1.801 1.53,0.982 false 1.251,0.806 1.660,0.963 0.409,0.158 10 GND6 2.648,1.994 2.942,2.761 false 2.776,2.782 3.134,2.940 0.357,0.158 10 GND

Turn the power switch off (lock).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-28 (GND) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A41-27 (GND2) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A41-26 (GND3) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A41-25 (GND4) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A41-24 (GND5) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A41-23 (GND6) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))



OK

7.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

7.RECONFIRM DTC
a.

Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.



c.

Turn the power switch on (ready).


d.

Perform a road test.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1241/41 and C1242/42 are not output. A
DTCs C1241/41 and/or C1242/42 are output (for LHD). B
DTCs C1241/41 and/or C1242/42 are output (for RHD). C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY