The skid control ECU acquires the steering angle sensor zero point every time the power switch is turned on (IG) and the vehicle is driven at 35 km/h (22 mph) or more for approximately 5 seconds. The ECU also stores previous zero points.
DTCs C1439/66 and C1445/66 will be cleared when the power switch is turned off (lock).
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1439/66 | 752 | After the steering angle sensor zero point calibration is cleared due to, for example, fluctuations in the power source, the steering angle sensor zero point calibration cannot be obtained for 0.048 seconds of continuous driving. | ·
Steering angle sensor (Spiral cable with sensor sub-assembly) ·
Yaw rate and acceleration sensor (Airbag sensor assembly) ·
Skid control ECU (Brake booster with master cylinder assembly) |
| C1445/66 | 753 | Steering angle sensor zero point calibration cannot be obtained when the vehicle is driven without a record of steering angle sensor zero point calibration at a speed of 35 km/h (22 mph) or more for 60 seconds or more. | ·
Steering angle sensor (Spiral cable with sensor sub-assembly) ·
Yaw rate and acceleration sensor (Airbag sensor assembly) ·
Skid control ECU (Brake booster with master cylinder assembly) |
Before proceeding with the inspection, explain to the customer that the output DTC is related to temporary loss of the steering angle zero point calibration, such as when the power source voltage drops when the auxiliary battery is removed, and confirm that this condition occurred.
When DTC U0073/94, U0123/62, U0124/95 and/or U0126/63 is output together with DTC C1439/66 and/or C1445/66, inspect and repair the trouble areas indicated by DTC U0073/94, U0123/62, U0124/95 and/or U0126/63 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>U0073/94).
When the speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) has a malfunction, DTCs for the steering angle sensor (spiral cable with sensor sub-assembly) may be output even when the steering angle sensor (spiral cable with sensor sub-assembly) is normal. When DTCs for the speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) are output together with other DTCs for the steering angle sensor (spiral cable with sensor sub-assembly), inspect and repair the speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) first, and then inspect and repair the steering angle sensor (spiral cable with sensor sub-assembly).
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off (lock).
Turn the power switch on (IG) again and check that no CAN communication system DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).
Drive the vehicle and turn the steering wheel to the right and left at a speed of 35 km/h (22 mph) and check that no speed sensor, yaw rate and acceleration sensor and steering angle sensor DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1439/66 and/or C1445/66 are output. | A |
| CAN communication system DTC is output. | B |
| Speed sensor, yaw rate and acceleration sensor and/or steering angle sensor DTC is output. | C |
| DTCs C1439/66 and C1445/66 are not output. | D |
When DTCs indicating CAN communication system malfunctions are output, repair the CAN communication system before repairing each corresponding sensor.
If there is a malfunction in the speed sensor or yaw rate and acceleration sensor (airbag sensor assembly), an abnormal value may be output although the steering angle sensor (spiral cable with sensor sub-assembly) is normal.
If the speed sensor and the yaw rate and acceleration sensor DTCs are output simultaneously, repair the sensors and inspect the steering angle sensor (spiral cable with sensor sub-assembly).
If the same DTC C1439/66 and/or C1445/66 is not output again, the DTC may have been stored due to a temporary loss of the steering angle zero point calibration, such as when the power source voltage drops.
A
B
(See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
C
D
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for at least 5 seconds.
Check that the steering wheel is centered correctly while driving straight ahead.
If the front wheel alignment and steering position are adjusted as a result of an off-centered position of the steering wheel, acquire yaw rate and acceleration sensor zero point again after the adjustments are completed.
The steering wheel is centered correctly.
OK
NG
Turn the power switch off (lock).
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (ready).
Drive the vehicle and turn the steering wheel to the right and left at the speed of 35 km/h (22 mph) or more.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1439/66 and C1445/66 are not output. | A |
| Yaw rate and acceleration sensor and/or steering angle sensor DTC is output | B |
If the same DTC C1439/66 and/or C1445/66 is not output again, the DTC may have been stored due to a temporary loss of the steering angle zero point calibration, such as when the power source voltage drops.
A
B